Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Conference2-91
Chapter 2 - Features and Operation
Conference Enable/Disable
Description
The Conference Enable/Disable feature allows administering of the system conference
feature on a per station basis for the ability of a station to initiate a conference.
Programming Steps
1. PressFLASHand dial[50]. Flexible button #24 (New Range) is lit and the following
message displays:
2. Enter the range of station numbers to be programmed. If only one station is being
programmed, enter that number twice (100...

2-92Conference
Chapter 2 - Features and Operation
Conference / DISA Timer
Description
The Conference/DISA Timer determines the time an unsupervised conference can continue
after the initiator of the conference has exited.
The Conference/DISA Timer setting is variable from 01-99 minutes. A 00 entry disables the
timer and no automatic disconnect occurs.
Programming Steps
1. Press the CONFERENCE/DISA TIMER flexible button(FLASH 01, Button #9). The following
message displays:
2. Enter a valid number on the...

Conference2-93
Chapter 2 - Features and Operation
5. If the next conference party is an outside line and a busy or wrong number is
encountered, press one of the conference parties on hold. This drops the busy or wrong
number party. Press the conference button again and repeat step 4.
6. When last party answers, press the CONF button twice. (All parties are connected.)
To exit a Conference (controller only) perform ONE of the following:
1 -- Press the ON/OFF button to ON, press MUTE, then replace the...

2-94 Cordless Key Telephone Unit Feature Button
Chapter 2 - Features and Operation
To set up a Conference with Personal Park:
1. While connected to an outside line, depress the hookswitch momentarily. The intercom
dial tone sounds.
2. Dial [438]. The first call is placed in personal park.
3. Dial desired number for second call.
4. Depress the hookswitch momentarily. The Intercom dial tone sounds.
5. Dial [664]. All three parties are conferenced.
6. Hang up to terminate the conference.
Conditions...

Database Administration2-95
Chapter 2 - Features and Operation
5. Press the CORDLESS KEY flexible button (Flash 50, Page B, Button #17) to assign the
FEAT Buttons. The following message displays:
XX = Assigned FEAT Button (01-24 = Button 1-24, 01-30 for Large Screen Display telephone)
00 = None
DEFAULT…No button (00) is assigned to the FEAT.
Database Administration
Administration Access
Description
The Administration Access feature allows a station to access Database Administration. Each
station can be...

2-96Database Administration
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
XXX-XXX = Station Range
4. Press the ADMIN ACCESS flexible button (FLASH 50, Page A, Button #18).Thefollowing
message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disable
[1] = Enable
6. Press HOLD to save the entry. A confirmation...

Database Printout (Dump)2-97
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…Admin Password is set for 3226.
Database Printout (Dump)
Description
Through a system programming command, either portions of or a complete database dump
can be printed using the RS-232C connector located on the Master Processor Board (MPB), on
theXTS.
The Print System Database command dumps the entire database as a permanent record
which can serve...

2-98Dial Pulse Sending
Chapter 2 - Features and Operation
Dial Pulse Sending
Description
Each CO interface circuit for outside lines can be programmed to send dial pulse or DTMF
signals. Dialing speed and break/make ratios are programmable.
Dial Pulse Parameters
Description
The Dial Pulse option lets the installer adjust the dial pulse ratio and speed when using dial
pulse (rotary) type signaling. By default, all lines are DTMF (tone) signaling. If pulse dialing is
required, the individual outside line...

Direct Inward Dialing2-99
Chapter 2 - Features and Operation
Programming Steps
1. Press the PULSE DIAL I/D TIMER flexible button(FLASH 02, Button #5). The following
message displays:
2. Enter a valid number on the dial pad that corresponds to 300-600 ms.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…Pulse Dial Ring Timer is set for 300 ms.
Pulse-to-Tone Switchover
Description
When commanded, the system changes the signaling on an outside line from dial pulse...

2-100Direct Inward Dialing
Chapter 2 - Features and Operation
When entering DID Table programming, buttons on a digital phone are defined as shown:
By default, all entries in the DID Table (000-999) have phone numbers assigned. Refer to
Table 2-6: DID & ICLID Default Table Entriesfor additional information.
The DID feature provides one-way direct inward dialing access to specific stations on specific
DID lines from the public telephone network, without going through an Attendant
answering position. DID...