Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

CO Flexible Port Assignment2-61
Chapter 2 - Features and Operation
Programming Steps
If the CO Line numbers need to be relocated to different ports, pressFLASHand dial[42].
The following message displays:
Buttons 1 through 18 indicate Ports 1 through 144. When the relocation program is initially
entered, Button #1 is lit to indicate that the user is programming the CO Line numbers.
To change the CO Line number assigned to any port:
1. Dial the position number on the display (01 through 08).
2. Then dial...

2-62CO Line - Access
Chapter 2 - Features and Operation
CO Line - Access
Description
Through programming, telephones are allowed or denied access to particular outside lines or
line groups. Refer to“Line Group Access - Station”on page 2-68,“Flexible Button”on page 2-138,
and“CO Line Group Programming”on page 2-69.
Operation
To access an outside line:
1. Press idle CO line button, POOL button,
-or-
Dial CO line group access code or LCR code: 9, 801-823, 88+LLL (LLL = CO Line number).
2. Dial desired...

CO Line Attributes2-63
Chapter 2 - Features and Operation
CO Line Attributes
Initialize CO Line Attributes
Description
CO Line parameters may be initialized to set all data fields to their original, default values. The
following data fields are returned to their default value upon initializing the CO Line
Attributes.
Table2-4:COLineAttributeDefaults
Program
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
FLASH 40
PA G E A1 DTMF/Dial Pulse Programming DTMF
2CO/PBXProgramming CO
3 Universal...

2-64CO Line Attributes
Chapter 2 - Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button (FLASH 80, Button #2). The following
message displays:
2. Press the HOLD button. A confirmation tone sounds.
FLASH 40
PA G E C1 Flash Timer Programming 10=1.0 sec
2 Ring Delay Timer 00=Disabled
3 Wink Timer 140 ms
4 Release Timer 020=200 ms
5 Reseize Timer 200=200 ms
6 Guard Timer 05=.5 sec
7 Seize Timer 010=0.1 sec
8 Preset Forward Timer 10 sec
9 DID Collect Timer 015=150 ms
10 T-1...

CO Line Attributes2-65
Chapter 2 - Features and Operation
PrintCOLineAttributes
Description
The Print CO Line Attributes command dumps the entire database as a permanent record
which can serve as a hardcopy of the database The system baud rate must match that of the
printer or receiving device.
When printing the CO Line attributes the following data prints:

2-66CO Line DTMF Sending
Chapter 2 - Features and Operation
Programming Steps
1. Press the CO LINE ATTRIBUTES flexible button(FLASH 85, Button #2). The following
message displays:
2. To print data for:

CO Line DTMF Sending2-67
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit. The following message displays to indicate current
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the DTMF/DIAL PULSE flexible button(FLASH 40, Page A, Button #1).
5. Enter a 0 or 1 that corresponds with the following entries:
[0] = Dial Pulse
[1] = DTMF
6. Press HOLD to save the entry. A...

2-68CO Line Group
Chapter 2 - Features and Operation
CO Line Group
Description
Outside lines can be placed in one of twenty-four groups if the customers business requires
such grouping. Stations are then individually assigned access to these groups and given the
ability to dial on particular lines.
Line Group Access - Station
Description
A station can access any combination of outside line groups, or a station may not be allowed
access to outside lines. CO line groups are used primarily by single line...

CO Line Group2-69
Chapter 2 - Features and Operation
6. To add a Line Group, enter a valid number (00, or 01–23) to designate the outside line
groups that the station can access, press 1, and then press HOLD to save the entry. A
confirmation tone sounds and the display updates.
7. To delete a Line Group, enter a valid number (00, or 01-23), press 0, and then press HOLD.
A confirmation tone sounds and the display updates.
DEFAULT…Stations are allowed access to Group 1.
CO Line Group Programming...

2-70CO Line - Identification
Chapter 2 - Features and Operation
4. Press the CO LINE GROUP flexible button(FLASH 40, Page A, Button #8).
5. Enter a valid number on the dial pad (0-23) which corresponds to Groups 0-23.
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…All lines are placed in Line Group 1.
CO Line - Identification
Description
The CO Line Identification feature allows entering a name into the database for each
individual line (trunk) connected to...