Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Call Forward2-31
Chapter 2 - Features and Operation
Call Forward - External (Off-Net)
Description
Stations are allowed to forward intercom and transferred CO line calls to an off-net location.
The Call Forward Off-Net feature allows a station to reroute calls that would normally be lost.
Calls can be forwarded to home or another off-net site. Initially ringing CO calls cannot be
forwarded with this feature.
Operation
To activate Off-Net Call Forwarding:
1. Lift handset or press ON/OFF button.
2. Press...

2-32Call Forward
Chapter 2 - Features and Operation
Call Forward No Answer Timer
Description
The Call Forward No/Answer Timer is used when a station in the system specifies that no
answer calls be forwarded to another station. The timer determines how long an intercom or
transferred call rings before it is considered a no-answer call.
The call then forwards to the designated station for handling. The Call Forward No/Answer
Timer setting is variable from 000-600 seconds.
Programming Steps
1. Press the...

Call Forward - Preset2-33
Chapter 2 - Features and Operation
Call Forward Display
Description
When call forwarding is invoked, the LCD display normally indicates the call forwarding mode
at all times.
This feature is enabled/disabled in administrative programming on a system-wide basis.
Programming Steps
1. Press the CALL FWD DISPLAY STATUS flexible button(FLASH 06, Button #4).The
following message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable Call Forward Display.
[0] = Disabled
[1] =...

2-34Call Forward - Preset
Chapter 2 - Features and Operation
Preset Call Forward - Per CO Line-- The Preset Call Forward feature allows each CO line
to be preset call forwarded on a per CO line basis. This allows a CO line to initially ring at
multiple stations and forward to a predetermined destination. The destination can be a
station or Hunt Group. Each CO line has a Preset Forward Timer. Each CO line also has a
VMID field to allow specific VM digits to be sent when a CO line forwards to a VM group....

Call Forward - Preset2-35
Chapter 2 - Features and Operation
2. Enter the range of station numbers to be programmed. To program only one station,
enter the number twice (100 100).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit.
4. Pressbutton#21.ThedisplayupdatestoreflectcurrentprogrammingforPageC.
XXX-XXX = Station Range
Internal No Answer Destination
1. PressFLASH 50,Page C, Button #1. The following message displays:
2. Enter a...

2-36Call Forward - Preset
Chapter 2 - Features and Operation
External Busy Destination
1. PressFLASH 50,Page C, Button #4. The following message displays:
2. Enter a valid number and press HOLD.
3. To delete the entry, press the [#] key and then press HOLD.
No Answer Timer
1. PressFLASH 50,Page C, Button #5. The following message displays:
2. Enter a valid number (00-99) and press HOLD (00=disable).
DEFAULT…No Answer Timer is set at 10 seconds.
Conditions
»Station Forwarding overrides the Preset Forward...

Call Forward - Preset2-37
Chapter 2 - Features and Operation
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the PRESET FWD DESTINATION flexible button(FLASH 40, Page B, Button #5).The
following message displays:
6. Enter a valid forward destination on the dial pad.
[9020-9999] = System Speed Bins
[100-351] = Station Extensions
[440-447] = Voice Mail Groups 1-8
[450-457] = Hunt Groups 1-8
[550-557] = UCD Groups 1-8
[550-565] = ACD Groups...

2-38Call Forward - Preset
Chapter 2 - Features and Operation
Preset Forward Timer (Incoming Call to a Destination)
Description
The Preset Forward Timer determines the time an outside line rings before being forwarded
to a predetermined destination as programmed in FLASH 50, Page C, Buttons 1-4. If a forward
destination is programmed in the CO line field, the CO calls forward to that destination after
the CO preset forward timer expires. This forward occurs regardless of how many stations the
line is...

Calling Forward Override2-39
Chapter 2 - Features and Operation
Preset Forward Timer (Incoming Call to a Station)
Description
The Preset Forward Timer determines the time an outside line rings before being forwarded
to a predetermined station within the local system. This entry works with Preset Forward
station assignments in Station Programming. More than one station can be forwarded to the
same party.
This timer also governs the time the DISA call rings at a station before returning to intercom
dial...

2-40 CallingStationHandsfreeModeOverride
Chapter 2 - Features and Operation
Calling Station Handsfree Mode Override
Description
Enables a calling station to override a called station’s T intercom setting.
Operation
When placing a call to a station and handsfree is desired:
1. Dial [7#] on the dial pad.
2. Dial the extension number,
-or-
Press DSS button of desired station (call tone rings station).
Calling Station Tone Mode Override
Description
Enables a calling station to override a called station’s H...