Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Hunt Groups2-151
Chapter 2 - Features and Operation
Calls directly to stations (by calling the extension number) within the hunt group do not hunt
but receive call progress tones from the extension.
Pilot All Ring Hunting --rings all idle stations in a particular Hunt group at one time.
Station (Circular) Hunting-- Transferred CO, and intercom calls that are presented to a busy,
or DND station, that are members of a Station Hunt Group, search sequentially (in the order
the extensions were entered in...

2-152Hunt Groups
Chapter 2 - Features and Operation
Programming Steps
1. Press the HUNT GROUPS flexible button (FLASH 80, Button #10). The following message
displays:
2. Press the HOLD button. A confirmation tone sounds.
PrintHuntGroupParameters
Description
The Print Hunt Group command dumps the entire database as a permanent record which can
serve as a hardcopy of the database. The system baud rate must match that of the printer or
receiving device.
Programming Steps
1. Press the HUNT GROUPS flexible...

Idle Speaker Mode2-153
Chapter 2 - Features and Operation
Idle Speaker Mode
Description
The Idle Speaker Mode feature allows you to select whether the first digit dialed is audible
over the digital telephone speaker. This feature is allowed or denied on a system-wide basis
in programming.
Programming Steps
1. Press the IDLE SPEAKER MODE flexible button(FLASH 05, Button #10).
2. Enter a 0 or 1 that corresponds with the following entries:
[0] = First digit dialed is audible (Disabled)
[1] = First digit...

2-154Intercom
Chapter 2 - Features and Operation
This feature can be programmed on any key station or DSS Console with an available flexible
button. If there is an available intercom button, a station calling that station cannot OHVO,
Camp On, or Override that station. Depending on the key station programming, intercom
ringing is muted or reminder ringing.
If all intercom buttons are in use, then the station may utilize the Camp On or Executive
Override features. By default, no intercom buttons are...

Intercom2-155
Chapter 2 - Features and Operation
»This feature can be programmed on any key station or DSS Console with an available
flexible button. If there is an available intercom button, the following actions cannot be
performed: Executive Override, ACD Supervisor Barge-In, OHVO, Camp On or Override.
»A call ringing to a station on an intercom button rings muted or reminder ringing,
depending on the stations tone ringing cadence.
»Up to five internal parties can be placed on hold. No recall timers...

2-156Intercom
Chapter 2 - Features and Operation
In the H mode(No LED), you hear three bursts of tone and an announcement.
Replyhandsfreeorliftthehandsetforprivacy.
 SINGLE LINE TELEPHONE
To place an intercom call:
1. Lift the handset.
2. Dial the intercom number.
You will hear ringing if the called station is in the“T”answering mode or two bursts of
tone if the called station is in the“H”or“P”positions.
3. Hang up to end the call.
To answer an intercom call:
Lift the handset,
-or-
If your SLT is...

Intercom2-157
Chapter 2 - Features and Operation
Programming Steps
1. Press the ICM HOLD BTN flexible button(FLASH 07, Button #19).
2. Enter a valid number (00-28) on the dial pad to correspond to one of the 29 available
options. (Refer toTable 2-13 on page 2-137.)
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…Intercom Hold Button flash rate is set for a Red 15 ipm Flash (09).
Intercom Signaling Select
Description
Users can control the method by which they...

2-158Inter-Digit Time-Out
Chapter 2 - Features and Operation
Inter-Digit Time-Out
The Inter-Digit Time-Out feature allows programming of the inter-digit time-out on a
system-wide basis. This feature applies to intercom and LCR calls. DISA inter-digit time-out
remains unaffected by this timer. The Inter-Digit Time-out setting is variable from
1-99 seconds.
Programming Steps
1. Press the INTER-DIGIT TIMEOUT flexible button(FLASH 01, Button #20). The following
message displays:
2. Enter a valid number on...

ISDN2-159
Chapter 2 - Features and Operation

2-160ISDN
Chapter 2 - Features and Operation
Programming Steps
1. PressFLASH 40, Page A, Button #16to enable or disable extended key telephone
service. The following message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
4. Reset the KSU,
-or-
Reset only the card using“config”without resetting the whole telephone switch. To do
this, typeconfigat theEnter...