Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Networking Tables2-201
Chapter 2 - Features and Operation
To program a phone number into the translation table:
1. Press the PHONE NUMBER flexible button(FLASH 55, Button #2)to enter the desired
phone number into the translation table. Maximum length of a phone number is
14 characters, including spaces and dashes. For example, to enter 1-480-443-6000, press:
[1]+[#]+[1]+[3]+[4]+[#]+[8]+[#]+[0]+[#]+[1]+[3]+[4]+[#]+[4]+[#]+[3]+[#]+[1]+[3]+[6]+[#]
+[0]+[#]+[0]+[#]+[0]+[#] (Refer toFigure 2-3 on page 2-71for...

2-202Night Service
Chapter 2 - Features and Operation
Night Service
Description
TheXTScan be programmed so it is automatically placed into and out of night mode. A
programmable weekly time schedule lets the system administrator preset the time the
system goes into night mode, and the time night mode is removed on a daily basis, including
weekend operation.
The Attendant Night Service feature [631] provides a means to put the system in night mode
from any keyset or remove the system from night mode from...

Night Service2-203
Chapter 2 - Features and Operation
The default times for automatic night mode are:

2-204Off-Hook Signaling
Chapter 2 - Features and Operation
Manual Operation
The Attendant(s) can control the use of Night Mode manually by pressing the NIGHT (DND)
button [631]. An LED indicates when the system is in Night Mode operation (flashing =
Special Mode, off = Day Mode).
Night Class of Service (COS)
The system allows each station to be assigned a different COS for night operation. The night
COS goes into effect when the system is put into night mode manually or via the automatic
schedule....

Off-Hook Voice Over2-205
Chapter 2 - Features and Operation
The system defaults this option to muted ringing. CO calls may also be camped-on to a busy
station and receive muted ringing.
Off-Hook Voice Over
Description
Off-Hook Voice Over (OHVO) enables station users, off-hook on a CO or intercom call, to
receive a voice announcement through the handset receiver without completely
interrupting the existing call. Your voice is only heard through the handset of the called
party’s telephone. The Voice Over...

2-206Off-Hook Voice Over
Chapter 2 - Features and Operation
4. Press the OHVO flexible button(FLASH50,PageA,Button#9). The following message
displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…Off-Hook Voice Over is disabled for all stations.
Operation
To place an Off-hook Voice Over call:
When an OHVO station calls a busy OHVO station and a busy tone is received, the calling
OHVO...

Off-Hook Voice Over2-207
Chapter 2 - Features and Operation
The OHVO receiving station may press a preprogrammed Message button to respond to the
voice over announcement without being released from the current call (e.g., by pressing a
flexible button preprogrammed for the message IN MEETING, the calling station receives this
message on the LCD display). Refer to“Personal Messages”on page 2-214and to“Te x t
Messaging (Silent Response)”on page 2-273.
Option 3 --The OHVO receiving station may respond to...

2-208Outside Calls
Chapter 2 - Features and Operation
»If the receiving station is on-hook in speakerphone mode and a calling station initiates
OHVO, the receiving station receives a Camp On warning tone and normal Camp On
procedures are followed.
»The receiving station may send a message, and then press MUTE to talk to the calling
station. Each time a message is sent, the splash tone sounds and both displays are
updated.
»LEDs follow Camp On LED lamp sequences....

Paging2-209
Chapter 2 - Features and Operation
There are three External Paging Zones available. External paging requires a three-digit dialing
code and an externally provided amplifier and paging system. Each zone can have a relay
contact associated to it.
There are eight internal paging zones available. A station can be in any or all zones or in no
zone at all. Stations not assigned to a page group can still make page announcements, if
allowed in station programming. Stations can be assigned to a page...

2-210Paging
Chapter 2 - Features and Operation
3. Speak in normal tone of voice to deliver message.
4. Replace handset to terminate the page announcement.
Paging Access
Programming Steps
1. PressFLASHand dial[50]. Flexible button #24 (New Range) is lit and the following
message displays:
2. Enter the range of station numbers to be programmed. If only one station is being
programmed, enter that number twice (100 100).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates....