Home
>
Triad
>
Telephone
>
Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide
Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide
Here you can view all the pages of manual Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide. The Triad manuals for Telephone are available online for free. You can easily download all the documents as PDF.
Page 261
Ring Down/Hot Line/Off-Hook Preference 2-231 Chapter 2 - Features and Operation Off-Hook Preference Programming (Via a Station) If your phone is programmed for Off-Hook Preference and you were given the ability to enable or change the prime flexible button: 1. Dial [691] on the dial pad. 2. Dial the desired button number. Refer to the following chart. To disable Off-Hook Preference: 1. Dial [691] on the dial pad. 2. Dial [00] on the dial pad. SINGLE LINE TELEPHONES When establishing an Off-hook...
Page 262
2-232Save Number Redial (SNR) Chapter 2 - Features and Operation Save Number Redial (SNR) Description Any number dialed on an outside line can be saved permanently and used at any time. This number is saved until a new number is stored. Operation To save the last number dialed: 1. After placing an outside call, keep handset off-hook. 2. Press the SPEED button twice. To dial a number that was saved (using the steps above): 1. Press the SPEED button. 2. Dial the [ ✳]button.
Page 263
Single Line Telephone2-233 Chapter 2 - Features and Operation Single Line Telephone Compatibility Description TheXTSsupports industry standard 2500-type (DTMF) single line telephone (SLT) instruments. When the Single Line Interface Board (SLIB) is installed in theXTS, a maximum of 240 single telephones can be supported. SLT DTMF Receiver Timer Description Single line telephones require the use of a DTMF receiver when going off-hook and dialing. When SMDR or toll restriction (via COS assignments) is...
Page 264
2-234Single Line Telephone Chapter 2 - Features and Operation Programming Steps 1. Press the SLT HOOK FLASH TIMER flexible button(FLASH 01, Button #14). The following message displays: 2. Enter a valid number on the dial pad that corresponds to 0.5-2.0 seconds in 1/10 second increments. 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. DEFAULT…SLT Hook Flash Timer is set at 10 (one second). SLT Hook Flash Bounce Timer Description The SLT Hook Flash Bounce Timer...
Page 265
Software Identification (MPB) 2-235 Chapter 2 - Features and Operation 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. DEFAULT … SLT Hook Flash Bounce Timer is set to 0.30 seconds. Software Identification (MPB) Description When a station dials feature code [610] on a display telephone, the system expects the next digits dialed to be a software identification code. This code is used to upgrade to a new version of software, e.g. upgrade from basic software to ACD...
Page 266
2-236Speakerphone Chapter 2 - Features and Operation Speakerphone Both Enhanced and Executive Digital Telephones are equipped with a speakerphone. Speakerphone Options Description The speakerphone can be programmed to work in one of three ways:
Page 267
Speakerphone2-237 Chapter 2 - Features and Operation 6. Enter a valid number (0-4) on the dial pad to identify the speakerphone operation. [0] = Works as normal speakerphone. Full speakerphone capabilities on CO lines and Intercom. [1] = Speakerphone enabled for intercom calls only. Speakerphone capabilities disabled for outgoing CO line calls (monitoring and on-hook dialing are still permitted). [2] = Permits toggling of speakerphone and headset operation via the [634] Headset code. [3] = Forces the...
Page 268
2-238Speed Dial Chapter 2 - Features and Operation Speed Dial Station Speed Dial Numbers Description A keyset user can associate up to 20 frequently dialed numbers as Station Speed Numbers (9000 to 9019). Telephone numbers can be up to 24 digits including pauses, flash commands, pulse-to-tone switchover, and no-display characters. A pause is automatically inserted after a flash. There are 3000 speed locations inXTSsystems for dividing among all telephones. Operation To use speed dial: 1. If an outside...
Page 269
Speed Dial2-239 Chapter 2 - Features and Operation Toeraseanexistingspeedbin: 1. Press the SPEED button twice. 2. Dial the speed bin location. 3. Press the SPEED button again. A confirmation tone sounds. SINGLE LINE TELEPHONE To use speed dial: 1. Lift handset. 2. Dial [668] on the dial pad. 3. Dial desired station or system speed bin number (9000-9999). 4. Replace the handset to end the call. To store speed dial numbers: 1. Lift handset. 2. Dial [661] on the dial pad. 3. Dial desired station speed...
Page 270
2-240Speed Dial Chapter 2 - Features and Operation 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 is lit. The display updates to reflect current programming for Page A: XXX-XXX = Station Range 4. Press the SPEED flexible button(FLASH 50, Page A, Button #6). The following message displays: 5. Enter a 0 or 1 on the dial pad to enable/disable this feature. [0] = Disabled [1] = Enabled 6. Press HOLD to save the entry. A confirmation tone sounds....