Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Toll Restriction2-281
Chapter 2 - Features and Operation
4. Press the HOLD button to save the entry. A confirmation tone sounds and the display
now updates.
5. When all entries for one table are complete, press the flexible button for the next table.
To erase a bin number:
1. Enter a valid bin number.
2. Press the HOLD button.
Deny Table
Description
Each Deny Table contains ten bin numbers. Each bin number may be up to eight-digits
including {Do Not Care} digits. Entries in the Deny Table represent...

2-282Toll Restriction
Chapter 2 - Features and Operation
Special Table
Description
The Special Tables provide greater flexibility in designing a toll plan for a particular site.

Toll Restriction2-283
Chapter 2 - Features and Operation
To enter office codes in a special table:
1. Press the SPECIAL TABLE (#1 to #4) flexible button(FLASH 70, Buttons #5 to #8)that
corresponds to the area code programmed above. The following message displays:
XXX = Area Code
2. Enter the office codes that are to be allowed or removed as follows:
XXX [1] = Allow Code
XXX [0] = Remove Code from the list
(XXX = An office code from 200 to 999)
3. Press HOLD after every code entered. A confirmation tone...

2-284Toll Restriction
Chapter 2 - Features and Operation
To view entries in a special table:
Six 3-digit codes allowed display in ascending order starting with the lowest entry.
Press the DISPLAY TABLES button again, the next 6 entries display. This continues until all
codes are displayed.
XXX= Area Code
YYY= Allowed Office Code
Initialize Exception Tables
Description
The Exception Tables parameters, including the Allow/Deny Tables and the Special Tables,
may be initialized setting all tables to their...

Toll Restriction2-285
Chapter 2 - Features and Operation
Print Exception Tables
Description
The Print Exception Tables command dumps the entire database as a permanent record
which can serve as a hardcopy of the database. The system baud rate must match that of the
printer or receiving device.
When printing information from the Exception Tables, the following data prints:

2-286Toll Restriction
Chapter 2 - Features and Operation
Programming Steps
1. Press the EXCEPT TABLES flexible button(FLASH 85, Button #5). The following message
displays:
2. To print the Except Tables, press the HOLD button. The following message displays:
When the system finishes sending the requested information to the printer, a
confirmation tone sounds.
Toll Restriction Related Items
CO/PBX Lines
When CO lines are marked as PBX lines the system first checks the PBX code table for a valid
match. If...

Uniform Call Distribution2-287
Chapter 2 - Features and Operation
Two (2) options are available to help alleviate this problem:
1. Shorten the SLT receiver timer [FLASH 01] [Button 12]. This frees up DTMF receivers faster,
but may not provide the desired toll restriction for SLT stations.
2. Enable LCR and force LCR on SLT stations.
When the LCR database is set up, the 3-digit table allows entry of the number of digits to
expect. When a SLT dials the appropriate number of digits, LCR releases the DTMF...

2-288 Universal Day/Night Answer
Chapter 2 - Features and Operation
Universal Day Answer (UDA)
Description
UDA-assigned CO lines can signal over external page port(s). External Day ringing is
programmed on a system-wide basis in administrative programming. Stations that do not
have access to a line during the day can answer that line while the System is in the day mode
by dialing a UDA code [#5]. To use this feature, a LOOP button or an appearance of the trunk
must be present on the station.
Programming...

Universal Day/Night Answer2-289
Chapter 2 - Features and Operation
»If External Day ring is disabled, or the system is not in the day mode, external page
ringing is disabled.
»Ringing CO lines not assigned CO line group access for a particular SLT may be answered
in a UDA service. Dialing privileges are unavailable on CO lines to which an SLT does not
have access. CO lines without UDA status may not be answered or accessed via UDA
procedures.
»If two single-line telephones attempt to retrieve one ringing...

2-290Vo i c e M a i l
Chapter 2 - Features and Operation
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…UNA is enabled.
Vo i c e Ma i l
Description
Up to 8 Voice Mail groups can be configured in theXTSsystem. Each group can contain up to
24 Voice Mail designated ports, each of which interfaces with a port on an SLT card (or DIDB if
using a Digital Voice Mail).
An externally provided Voice...