Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

3
Attendant Features and
Operation
The Attendant and Attendant(s) with DSS/DLS features of theXTSSystem are listed and
described in alphabetical order. Attendant features are in addition to digital station
features.
The instructions in this chapter are based on the use of a digital display telephone. 

» » » » » » »  NOTES   » » » » » » » 

Introduction3-3
Chapter 3 - Attendant Features and Operation
Introduction
The instructions in this chapter are based on the use of a digital display telephone.
TheXTSSystem provides the following keys, indicators and features:
Handset and Speakerare located at the left side of the front panel. A handset is provided to
allow confidential conversation when desired. Lifting the handset from its cradle (going
off-hook) disengages the station’s built-in speaker.
The speaker is located directly below the...

3-4Attendant Features - Index
Chapter 3 - Attendant Features and Operation

911 Attendant Alert3-5
Chapter 3 - Attendant Features and Operation
911 Attendant Alert
Description
The 911 Attendant Alert feature allows Attendants with a 911 flexible button to be alerted of
internal stations placing 911 calls. The Attendant can store the sixteen most recent 911 calls.
Calling information includes the time/date of the call as well as the station number that
placed the call.
When the 911 system feature is enabled (FLASH 06), this identifies which CO lines are to be
used for placing 911...

3-6 Attendant CO Line External (Off-Net) Forward
Chapter 3 - Attendant Features and Operation
Attendant CO Line External (Off-Net) Forward
Description
The Attendant CO Line External (Off-Net) Forward feature lets the first Attendant station
forward incoming CO calls to an off-net location. The Attendant must have a direct
appearance of the CO line to be forwarded. Forwarding can be established on a per CO line
group basis or on an all CO line groups basis. In a speed dial bin, store the number of the...

Attendant Custom Message3-7
Chapter 3 - Attendant Features and Operation
Operation
Program the ten custom messages at the first Attendant station as follows:
1. Dial the Custom Message program code [694] on the dial pad. The following message
displays:
2. Enter a valid message bin number [21–30]. The following message displays after the bin
number has been selected.
3. Enter the custom message using the dial pad keys to enter the letters as shown in
Figure 2-14 on page 2-198
.

3-8Attendant Day/Night/Special
Chapter 3 - Attendant Features and Operation
Attendant Day/Night/Special
Description
The system’sAutomaticNightModeFeaturecanbeoverriddenbytheAttendantstation.The
Attendant station user can press their DND button to place the system into Night Mode.
Any designated Attendant can place the system into Night Service.
Operation
1. Press the preprogrammed NIGHT SERVICE button (631, DND by default) once to activate
the Night mode (LED is lit solid).
2. Press the DND button again...

Attendant Directory List Programming 3-9
Chapter 3 - Attendant Features and Operation
The first entry (000) in the Directory List is shown on the display.
AAA = Directory List entry number (000-199)
XXXX = Either:,
A 3- or 4-digit station number (100-8999)
-or-
A 3-digit local number/name translation table number
(600-799 minus assigned station numbers that would
overlap)
-or-
A 4-digit remote device number (1000-8999 minus
assigned station numbers that would overlap)
-or-
A 4-digit station speed bin...

3-10 Attendant Directory List Programming
Chapter 3 - Attendant Features and Operation
7. Press HOLD, then use [✳] or [#] to scroll to next entry.
-or-
Hang up to end programming.
To clear an entry:
1. Select desired entry.
2. Press TRANS.
3. Press FLASH.
4. Press SPEED. Confirmation tone sounds and entry is erased.
The following procedure is used to associate names to the Local Number/Name Translation
Table number only.
1. Enter desired three-digit Directory List number (000-199), or dial [...