Home > Triad > Telephone > Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Here you can view all the pages of manual Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide. The Triad manuals for Telephone are available online for free. You can easily download all the documents as PDF.

Page 331

Voice Mail In-Band Features2-301
Chapter 2 - Features and Operation
Programming Steps
PressFLASHand dial[67]. The following message displays:
Voice Mail In-Band Digits
Description
The Voice Mail In-Band Digits feature enables and disables station in-band signaling.
Incoming CO callers can be Station Call Forwarded into voice mail only when the ringing CO
line is programmed to ring at one station. CO lines programmed to ring at an Attendant
station, call forward into the voice mail system (if programmed...

Page 332

2-302Voice Mail In-Band Features
Chapter 2 - Features and Operation
2. Enter a 0 or 1 to Enable/Disable this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…VM Transfer/Forward feature is enabled.
Vo i c e M a i l B r o k e r
Description
The Voice Mail Broker Calls feature modifies the operation of voice mail ports when disabled.
Broker operation is unavailable when using supervised transfers to stations. When enabled,
the...

Page 333

Voice Mail In-Band Features2-303
Chapter 2 - Features and Operation
Remote Voice Mail Programming
Description
This feature is used to specify the pilot hunt number of the centralized voice mail system in a
networking system. Refer to“Remote Voice Mail Programming”on page C-26.
Voice Mail Modem Access
Description
You can program Vodavi voice mail systems (other than MiniVoice or PathFinder) using the
telephone system modem.
Programming Steps
To enable or disable the VM port:
1. Press the VM PORT flexible...

Page 334

2-304 Voice Mail One-Touch Recording
Chapter 2 - Features and Operation
Conditions
»The use of this feature requires the use of a straight-thru modem cable connected from
the voice mail system to one of three ports on theXTSsystem. Use either port 5 on the
MPB2 or ports 3 or 4 on the optional SIU.
Voice Mail One-Touch Recording
Description
The Voice Mail One-Touch Recording feature allows the station user, while on an internal/
external call, to press a button and have the system record the conversation...

Page 335

Voice Mail One-Touch Recording 2-305
Chapter 2 - Features and Operation
Conditions
»If the user hangs up without terminating the record function, the system performs the
exit procedure as described in step 3 above.
»If the user presses the TRANS, CAMP ON, MSG, or FWD buttons during recording, pressing
the button is ignored.
»During the recording setup, pressing the CONF button is ignored.
»If a VM port isnot availablewhen the station user wants to record, the user receives the
following display (lasts...

Page 336

2-306Voice Mail Outpulsing Table
Chapter 2 - Features and Operation
Programming Steps
1. Press the ONE-TOUCH RCD WARNING TONE flexible button(FLASH 06, Button #10).The
following message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…Recording Warning Tone is enabled.
Voice Mail Outpulsing Table
Voice Mail In-Band Signaling
Description
Entries in one of the eight Voice...

Page 337

Voice Mail Outpulsing Table2-307
Chapter 2 - Features and Operation
Suggested Uses:

Page 338

2-308 Voice Over the Internet Protocol
Chapter 2 - Features and Operation
Voice Mail Disconnect Table
Description
A disconnect signal can be programmed into theXTSsystem to notify the VM system that a
call has been abandoned. This is accomplished through in-band signaling. If a CO or Intercom
disconnect signal is detected, theXTSsystem sends a series of DTMF digits programmed in
the voice mail disconnect table to the voice mail port. This can be any digit stream up to
12 digits including [
✳] and [#]....

Page 339

Vo l u m e C o n t r o l2-309
Chapter 2 - Features and Operation
Vo l u m e C o n t r o l
Operation
DIGITAL AND ELECTRONIC TELEPHONES
The volume control on the Digital Key Telephone controls ringing, handset, and
speakerphone volumes. It also affects the receive volume of the Wanderer cordless unit. The
volume on 8-button digital telephones is controlled by dialing feature code 638 and then
using [#] to increase volume or [✳]todecreasevolume.
The volume control on the Electronic Key Telephone consists of...

Page 340

2-310Vo l u m e C o n t r o l
Chapter 2 - Features and Operation
Using the handset on a CO call ...
Receiving a page announcement ...
Receiving an incoming tone ringing Intercom or CO call ...
.
 SINGLE LINE TELEPHONE
The volume control on the Single Line Telephone is located on the right side of the
telephone. The slider switch options are HI for loud volume, LO for low volume, and OFF to
turn the ringer off. Two-line models have a volume switch for each line. Certain models do
not have an OFF option....
Start reading Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Related Manuals for Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

All Triad manuals