Home
>
Triad
>
Telephone
>
Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide
Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide
Here you can view all the pages of manual Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide. The Triad manuals for Telephone are available online for free. You can easily download all the documents as PDF.
Page 201
ISDN Programming - Page B2-171 Chapter 2 - Features and Operation Programming Steps 1. PressFLASHand dial[45]. The following message displays: 2. Enter a valid number for the range of slots being programmed. If only one slot is being programmed, enter that number twice (02 02 = Slot 2, Cabinet 0). 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 (Page A) is lit. 4. Press button #20 to select Page B. The following message displays to indicate...
Page 202
2-172ISDN Programming - Page B Chapter 2 - Features and Operation Maximum Number Retransmission Description The Maximum Number of Retransmissions of a frame (N200) is a system parameter. Do not change the Maximum Number Retransmission setting unless advised to do so by Technical Support. Programming Steps 1. Press the MAX # RETRANSMSN flexible button(FLASH 45, Page B, Button #1). 2. Enter a valid number (0-9) on the dial pad. 3. Press the HOLD button. A confirmation tone sounds and the display updates....
Page 203
ISDN Programming - Page B2-173 Chapter 2 - Features and Operation Maximum TEI Request Description This feature is reserved for future use. Programming Steps 1. Press the MAX TEI RQST flexible button(FLASH 45, Page B, Button #3). 2. Enter a valid number (000-999) on the dial pad. 3. Press the HOLD button. A confirmation tone sounds and the display updates. DEFAULT…Maximum TEI Request setting is 003. Maximum XID Retransmission Description Do not change the Maximum number of XID Retransmissions setting...
Page 204
2-174ISDN Programming - Page B Chapter 2 - Features and Operation DEFAULT…T200 setting is 1 second. Minimum TEI ID Check Message Description The Minimum TEI ID Check Message feature sets the minimum time between retransmission of the TEI identity check messages. Do not change the Minimum TEI ID Check Message setting unless advised to do so by Technical Support. Programming Steps 1. Press the MIN TEI ID CHK MSG flexible button(FLASH 45, Page B, Button #6). 2. Enter a valid number (00-99 seconds) on the...
Page 205
ISDN Programming - Page B2-175 Chapter 2 - Features and Operation Programming Steps 1. Press the MSG EXCHANGE TIMER flexible button(FLASH45,PageB,Button#8). 2. Enter a valid number (00-99 seconds) on the dial pad. 3. Press the HOLD button. A confirmation tone sounds and the display updates. DEFAULT…Message Exchange Timer setting is 15 seconds. Minimum XID Retransmission Description The Minimum XID Retransmission setting establishes the minimum time between XID messages. Do not change the Minimum XID...
Page 206
2-176ISDN Programming - Page B Chapter 2 - Features and Operation Set-Up Timer Description The Set-up Timer setting establishes the response time to setup message. Do not change the Set-up Timer setting unless advised to do so by Technical Support. Programming Steps 1. Press the SET UP TIMER flexible button(FLASH 45, Page B, Button #11). 2. Enter a valid number (00-99 seconds) on the dial pad. 3. Press the HOLD button. A confirmation tone sounds and the display updates. DEFAULT…Set-up Timer setting is 10...
Page 207
ISDN Programming - Page B2-177 Chapter 2 - Features and Operation Release Request Description Do not change the Release Request setting unless advised to do so by Technical Support. Programming Steps 1. Press the RELEASE REQUEST flexible button(FLASH 45, Page B, Button #13). 2. Enter a valid number (00-99 seconds) on the dial pad. 3. Press the HOLD button. A confirmation tone sounds and the display updates. DEFAULT…Release Request Timer setting is 4 seconds. Link Disconnect Description Do not change the...
Page 208
2-178ISDN Programming - Page B Chapter 2 - Features and Operation Connect Request Description Do not change the Connect Request Timer setting unless advised to do so by Technical Support. Programming Steps 1. Press the CONNECT REQUEST flexible button(FLASH 45, Page B, Button #16). 2. Enter a valid number (00-99 seconds) on the dial pad. 3. Press the HOLD button. A confirmation tone sounds and the display updates. DEFAULT…Connect Request setting is 4 seconds. Restart Request Timer Description Do not...
Page 209
ISDN Programming - Page B2-179 Chapter 2 - Features and Operation Initialize ISDN/VoIP Parameters Description The ISDN/VoIP Parameters may be initialized setting all data fields to their original, default values. Table 2-15: ISDN Parameter Defaults Program CodeFlexible ButtonFeaturesDefault Value (after initialization) FLASH 45 PA G E AISDN PARAMETERS 1BRICOType NI1 2 PRI CO Type NI2 3Framing ESF 4 NT/TE Mode TE 5 Power Disabled 6 Directory Number None 7 Max Out I-Frames K 001 8 Leading 1 Enabled 9...
Page 210
2-180ISDN Programming - Page B Chapter 2 - Features and Operation Programming Steps 1. Press the ISDN/VOIP flexible button (FLASH 80, Button #15). The following message displays: 2. Press the HOLD button. A confirmation tone sounds. PAGE B 1 Maximum Number Retransmission 3 2 Maximum Octets 260 3 Maximum TEI ID Request 003 4 Maximum XID Retransmission 3 sec 5 T-200 01 sec 6 Minimum TEI ID Check Message 01 sec 7 Minimum TEI ID Request 02 sec 8 Message Exchange Timer 15 sec 9 Minimum XID Retransmission 3...