Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

ISDN2-161
Chapter 2 - Features and Operation
Programming Steps
1. PressFLASHand dial[40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible Button #19 (Page A) is lit.
4. Press the Page B flexible button (Button #20). The following message displays:
XXX-XXX = CO Line Range
5. Press the...

2-162ISDN
Chapter 2 - Features and Operation
SPID
Description
When you order an ISDN line, your phone company will give you a Service Provider Identifier
(SPID) for every phone number that you have. Each ISDN BRI line typically has two phone
numbers and thus two SPIDs. The SPID is an eight to 24-digit number that identifies the
services that you ordered.
Programming Steps
1. PressFLASHand dial[40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only...

ISDN Programming - Page A2-163
Chapter 2 - Features and Operation
ISDN Programming - Page A
Description
This section describes the procedures and steps necessary to program ISDN attributes. When
entering the ISDN attributes portion of the database, the programmer may decide to enter
information for a range of slots or one specific slot. Range programming lets the programmer
change a specific parameter or a few parameters for an entire range of slots, leaving intact
the remaining data fields that do not...

2-164ISDN Programming - Page A
Chapter 2 - Features and Operation
Basic Rate Interface (BRI) CO Type
Description
Changes to BRI CO Type area are not possible at this time (setting = NI1).
Programming Steps
1. PressFLASHand dial[45]. The following message displays:
2. Enter a valid number for the range of slots being programmed. If only one slot is being
programmed, enter that number twice (02 02 = Slot 2, Cabinet 0).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates....

ISDN Programming - Page A2-165
Chapter 2 - Features and Operation
DEFAULT…NI2 is the PRI CO type.
Framing
Description
Framing options include T1, ESF, and D4.
Programming Steps
1. Press the FRAMING flexible button(FLASH 45, Page A, Button #3).
2. To view a Framing setting, enter a valid number (0-2).
0=T1
1 = ESF
2=D4
DEFAULT…ESF is the framing setting.
NT / TE Mode
Description
The mode can be set for either network termination (NT) or terminal equipment (TE). Use the
NT setting only when using the PRI...

2-166ISDN Programming - Page A
Chapter 2 - Features and Operation
Power
Do not change the Power setting unless advised to do so by Technical Support.
Programming Steps
1. Press the POWER flexible button(FLASH 45, Page A, Button #5).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT - Power is disabled.
Directory Number - PRI
Description
The Directory Number is the main number...

ISDN Programming - Page A2-167
Chapter 2 - Features and Operation
2. Enter a valid number (000-127) on the dial pad.
3. Press the HOLD button. A confirmation tone sounds and the display updates.
Leading 1
Description
0 disables the leading 1 from being sent to the CO when users dial national long distance
numbers. 1 enables the leading 1 to be sent to the CO on national long distance numbers. If
enabled, and the user does not dial a 1, the 1 will automatically be applied.
Programming Steps
1. Press the...

2-168ISDN Programming - Page A
Chapter 2 - Features and Operation
7/8 Digit Number Plan
Description
The 7/8 Digit Number Plan is the specific plan that a particular Central Office uses for 7-digit
and 8-digit calls.
Programming Steps
1. Press the 7/8 DIGIT NUMBER PLAN flexible button(FLASH45,PageA,Button#10).
2. Enter a 0 or 1 on the dial pad to select the desired Number Plan.
[0] = Selects ITU number plan
[1] = Selects CO number plan
3. Press the HOLD button. A confirmation tone sounds and the display...

ISDN Programming - Page A2-169
Chapter 2 - Features and Operation
DEFAULT…Calling Number is enabled.
Loopback
Description
Do not change the Loopback setting unless advised to do so by Technical Support.
Programming Steps
1. Press the LOOPBACK flexible button(FLASH45,PageA,Button#12).
2. Enter a valid number (0-2) on the dial pad.
[0] = Normal mode
[1] = Near end mode
[2] = Far end mode
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT…Loopback setting is normal....

2-170ISDN Programming - Page B
Chapter 2 - Features and Operation
11-Digit Number Plan
Description
The 11 Digit Number Plan is the specific plan that a particular Central Office uses for 11-digit
calls.
Programming Steps
1. Press the 11 DIGIT NUMBER PLAN flexible button(FLASH 45, Page A, Button #14).
2. Enter a 0, 1, or 2 on the dial pad to select the desired Number Plan.
[0] = Selects ITU number plan
[1] = Selects CO number plan
[2] = Unknown
3. Press the HOLD button. A confirmation tone sounds and the...