Sharp Ux Cc500 5 In 1 Communication Center With Expandable C Operation Manual

							Clearing Paper Jams
119
10. Trouble-
shooting
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed properly during transmission or copying, 
or DOCUMENT JAMMED appears in the display, first try pressing  . If 
the document doesnt feed out, remove it as explained below.
Important:
Do not try to remove a jammed document without releasing it as explained 
below. This may damage the feeder mechanism.
START/MEMORY
1Press 
 and slowly open the operation 
panel until it is half open.
2Flip up the green levers on each side of 
the white roller.
3Gently remove the document.
•Be careful not to tear the document.
1
2

(
3
3
						

							Clearing Paper Jams
120
1Open the operation panel (press 
).
2Gently pull the jammed paper out of 
the machine, making sure no torn 
pieces of paper remain in the print 
compartment or rollers.
3Rotate the front gear until the film is taut, and then close the operation 
panel (press down on both sides to make sure it clicks into place).
Clearing jammed printing paper
4Flip down the green levers on each side of the white roller. Rotate the 
front gear until the film is taut, and then close the operation panel (press 
down on both sides to make sure it clicks into place).
1
2

(
3
3
						

							Ordering Parts
121
Ordering Parts
To order parts, contact the parts distribution center located nearest 
you. When ordering a part, use the part order number shown below. 
Operation manual  TINSE4273XHTZ
Setup Guide TCADZ3323XHZA
Handset cord QCNWG209BXHGY
Telephone line cord QCNWG208BXHZZ
Handset DUNTK468BXHGY
Paper tray CPLTP3183XHR7
Paper tray extension  LPLTP3184XHZZ
Gears CGERH2566XH01
NGERH2568XHZZ
AC adapter RADPA2027XHZZ
Cordless handset charger RUNTZ2100XHE2
Part distribution centers 
Tritronics, Inc. 
1306 Continental Drive 
Abingdon, MD 21009Tel: 1-800-638-3328 
Fax: 1-800-888-FAXD 
Tritronics, Inc. 
1015 NW 52nd Street 
Ft. Lauderdale, FL 33309Tel:1-800-365-8030 
Fax: 1-800-999-FAXD
Fox International, Ltd. 
23600 Aurora Road 
Bedford Heights, OH 44146Tel: 1-800-321-6993 
Fax: 1-800-445-7991
Andrews Electronics 
25158 Avenue Stanford 
Santa Clarita, CA 91355Tel: 1-800-274-4666 
Fax: 1-805-295-5126
Sharp Accessories and 
Supply Center 
2130 Townline Road 
Peoria, IL 61615Tel: 1-800-642-2122

(
3
3
						

							FCC Regulatory Information
122
FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted 
by the ACTA.  On the rear of this equipment is a label that contains, among other 
information, a product identifier in the format US:AAAEQ##TXXXX.  If requested, this 
number must be provided to the telephone company. 
A plug and jack used to connect this equipment to the premises wiring and telephone 
network must comply with the applicable FCC Part 68 rules and requirements adopted 
by the ACTA.  A compliant telephone cord and modular plug is provided with this 
product.  It is designed to be connected to a compatible modular jack that is also 
compliant.  See installation instructions for details. This equipment connects to the 
telephone network through a standard USOC RJ-11C network interface jack. 
The REN is used to determine the number of devices that may be connected to a 
telephone line.  Excessive RENs on a telephone line may result in the devices not 
ringing in response to an incoming call. In most but not all areas, the sum of RENs 
should not exceed five (5.0).  To be certain of the number of devices that may be 
connected to a line, as determined by the total RENs, contact the local telephone 
company.  For products approved after July 23, 2001, the REN for this product is part of 
the product identifier that has the format US:AAAEQ##TXXXX.  The digits represented 
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).  For earlier 
products, the REN is separately shown on the label. 
If this equipment causes harm to the telephone network, the telephone company will 
notify you in advance that temporary discontinuance of service may be required.  But if 
advance notice isnt practical, the telephone company will notify the customer as soon 
as possible.  Also, you will be advised of your right to file a complaint with the FCC if you 
believe it is necessary. 
The telephone company may make changes in its facilities, equipment, operations or 
procedures that could affect the operation of the equipment. If this happens the 
telephone company will provide advance notice in order for you to make necessary 
modifications to maintain uninterrupted service. 
If trouble is experienced with this equipment, or for repair or warranty information, 
please contact  Sharp’s Customer Assistance Center. The number is 1-877-794-8675. If 
the equipment is causing harm to the telephone network, the telephone company may 
request that you disconnect the equipment until the problem is resolved.
This equipment may not be used on coin service provided by the telephone company. 
Connection to party line service is subject to state tariffs.  Contact the state public utility 
commission, public service commission or corporation commission for information. 
If your home has specially wired alarm equipment connected to the telephone line, 
ensure the installation of this equipment ID does not disable your alarm equipment.  If 
you have questions about what will disable alarm equipment, consult your telephone 
company or a qualified installer.
This equipment is hearing-aid compatible. 
When programming and/or making test calls to emergency numbers: 
♦Remain on the line and briefly explain to the dispatcher the reason for the call. 
♦Perform such activities in the off-peak hours, such as early morning or late evening. 

(
3
3
						

							123
SHARPDate Revised: .Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (1/2)MSDS No. B-1026
Section 1. Product and Company Identification
Product Name :IMAGING FILM UX-5CR
Supplier Identification :Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Manufacturer :DAINIPPON PRINTING CO. LTD.
591-2, Kamihirose, Higashikubo, Sayamashi, Saitama, 350-1321 JAPAN
Emergency telephone number :+81-42-952-9666
Local suppliers are listed below. Please contact the nearest supplier for additional information.
Section 2. Ingredients
IngredientsCAS No.ProportionOSHA PELACGIH TLVOtherPolyethylene terephthalate film25038-59-9 47 ~ 52% - - None
Coating layer substances
Carbon Black 1333-86-4 7 ~ 10% 3.5 mg/m
33.5 mg/m3None
Ester wax 8015-86-9 2 ~ 7% - - None
Parraffin Wax 8002-74-2 10 ~ 14% - 2.0 mg/m
3None
Microcrystalline wax 63231-60-7 16 ~ 22% - - None
Ethylene Vinyl Acetate Copolymer24937-78-8 1 ~ 5% - - None
Others 1 ~ 6% - - None
Section 3. Hazardous Identification
Route(s) of Entry:Inhalation? Skin? Ingestion?
NO NO Possible but very unusual
Signs and Symptoms of Exposure:None
Medical Conditions Aggravated by Exposure:None
POTENTIAL HEALTH EFFECTS:
Inhalation:None
Skin Contact:None
Eye Contact:None
Ingestion:None
Section 4. First-Aid Measures
Inhalation: No applicableSkin Contact: In case of contact, usually special care in not necessary. If it dirties skin, clear with water and soap.Eye Contact: In case of contact, immediately flush eyes with plenty of water. If necessary, then care for medical attention.Ingestion: Immediately make vomit it and rinse mouth with water. If necessary, then care for medical attention.
Section 5. Fire-Fighting Measures
Flash Point:about 250°Cforink
Autoignition:None
Flammability Limits:Not applicable
Extinguishing Media:CO2, Water, Dry chemicals, Foam
Firefighting:None
Fire and Explosion Hazard:None
Hazardous Combustion Products:None (Country) (Name and Telephone Number)
U.S.A. Sharp Electronics Corporation
Telephone number for information: 1-800-237-4277
Canada Sharp Electronics of Canada Ltd.
Telephone number for information : 905-890-2100
Emergency telephone number : 1-800-255-3924

(
3
3
						

							124
SHARP
Date Revised: .Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (2/2)MSDS No. B-1026
Section 6. Accidental Release Measures
Rumpling the product may cause the wax layer to peel off. Sweep up or vacuum. When sweeping, avoid
raising film or dust. If a vacuum is used , motor should be rated as dust tight. Wash any residue off skin with
soap and water. Garments may be wasted or dry cleaned after removal of loose film or dust.
Section 7. Handling and Storage
No special precautions for safety reason.
Store in cool, dry place ,avoid direct sunlight.
Section 8. Exposure Control/Personal Protection
Ventilation:None
Eye Protection:None
Protective Clothing:None
Gloves:None
Section 9. Physical and Chemical Properties
Description:Not applicable
Melting Point:71°CFreezing Point:None
Pressurized:NoneBoiling Point:None
pH:NoneSpecific Gravity (H20 = 1):about 1.2
Evaporation Rate:NegligibleWater Solubility:Not applicable
Volatility:None
Section 10. Stability and Reactivity
Stability:Stable
Conditions to Avoid:None
Incompatibility(Materials to Avoid):None
Hazardous Decomposition or Byproducts:CO, CO2, NOX and H2O
Hazardous Polymerization:Will not occur
Section 11. Toxicological Information
Acute Toxicity:None
Chronic Toxicity:None
Section 12. Ecological Information
No environmental effect at normal use.
Section 13. Disposal Consideration
Dispose by the same method of ordinary plastic products in accordance with all applicable regulations. Any
disposal practice must be in compliance with local, state and federal laws and regulations. If necessary,
contact government office and ensure conformity with disposal regulations.
Section 14. Transport Information
No specific precautionary transport measure for safety reasons.
As to storage conditions, see section 7.
Section 15. Regulatory Information
None
Section 16. Other Information
The information herein is given in good faith, but no warranty, if used any process.
Final determination of suitability of any material is the sole responsibility of the user.
Although certain information are described herein, we cannot guarantee, that these are the only hazard, which exist.Information on this data sheet represents our current data and best opinion as to the proper use in handling of
this product under normal conditions.
Restrictions: This information relates only to the specific material designated as supplied by the manufacturer. This
information is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy and
accepts no responsibilities for any typographical errors which may appear on these sheets. It is the
responsibility of the user to determine the suitability of this product for each particular use.

(
3
3
						

							125
Quick Reference Guide
Sending Faxes
Place your document 
(up to 10 pages) face 
down in the document 
feeder.
Normal Dialing 
1. Lift the handset or press  .
2. Dial the fax number. 
3. Wait for the reception tone (if a person 
answers, ask them to press their Start 
key). 
4. Press  .
Automatic Dialing
1. Press   or   until the desired 
destination appears in the display.
2. Press  .
Direct Keypad Dialing  
1. Dial the fax number. 
2. Press .
Recording an OGM
1. Press  , press   until desired 
OGM is displayed, and then 
 once.
2. Lift the handset, press  , and 
speak into the handset.
3. When finished, press  .
SPEAKER
START/MEMORY
START/MEMORY
START/MEMORY
REC/
MEMO
START/MEMORY
STOP
Receiving Faxes
Press   until the arrow in the 
display points to the desired reception 
mode.
FAX mode: The fax machine automatically 
answers and receives faxes.
TEL mode: Answer all calls (even faxes) 
by picking up the handset. To begin fax 
reception, press  .
TAD mode: Select this mode when you go 
out to receive both voice messages and 
fa xes.
Storing Auto Dial Numbers
1. Press   once and   twice.
2. Enter the full fax/phone number.
3. Press  .
4. Enter a name by pressing number keys.
 
(To enter two letters in succession that 
require the same key, press   after 
entering the first letter.)
5. Press   and then  .
RESOLUTION/
RECEPTION MODE
START/MEMORY
FUNCTION
START/MEMORY
START/MEMORYSTOP
FAX TELJAN-02 10:30
FAX TELJAN-02 10:30
FAX TELJAN-02 10:30TAD
TAD TAD
RESOLUTION/
RECEPTION MODE
A =B =
C =
D =E =F =
G =H =I  =J =K =L =M =
N =O =P =Q =R =S =T =
U =V =W =X =Y =Z =
SPACE =

(
3
3
						

							126
Using the Cordless Phone
Making a phone call
1. Pick up the cordless handset and press 
.
2. When you hear the dial tone, dial the 
number. 
3. When you are ready to end the call, 
press . 
Making a phone call using automatic 
dialing
1. Press   once.
2.Press   or   to select the book.
3. Press   or   until the number you 
wish to dial appears in the display.
4. Press  .
Receiving a phone call
1. When the cordless handset rings, pick it 
up and press any key to answer.
2. When you are ready to end the call, 
press .
Receiving a fax using the cordless 
handset
If you hear a fax tone after answering a 
call on the cordless handset, or if the 
other party speaks to you and then 
wants to send a fax, press
 .
TALK
OFFOFF
SEARCH
TALK
OFFOFF
START
Storing auto dial numbers
1. Press  ,   or   to select 
the book, and then  .
2. Enter the full fax/phone number.
To clear a mistake, press  .
To insert a pause, press  .
3. Press .
4. Enter a name by pressing number keys.
 
(To enter two letters in succession that 
require the same key, press   after 
entering the first letter.)
5. Press   and then  .
Listening to messages 
1. Press . 
(For the general box, press  .)
2. Press   to listen to all your 
messages, or   to listen to only your 
new messages.
3. While listening, you can press 
, , , 
or .
4 When finished, press 
SEARCH
FUNCTION
/PAUSE
ERASE
HOLD
FUNCTION
/PAUSE
START
STARTOFFOFF
REMOTE
/FLASH
0
PQRS7PLAY
TUV8PLAY NEW
REPEAT0SKIPDELETE
STOPWXYZ9
OFFOFF
A =B =
C =
D =E =F =
G =H =I  =
J =
K =L =
M =
N =O =
P =
Q =R =S =
T =U =
V =
W =
X =Y =Z = SPACE =WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9TUV8
TUV8
TUV8TUV8TUV8TUV8
PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7MNO6MNO6MNO6MNO6MNO6
JKL5JKL5JKL5MNO6
JKL5JKL5JKL5GHI4GHI4GHI4GHI4GHI4GHI4
DEF3DEF3DEF3DEF3DEF3DEF3ABC2ABC2ABC2ABC2ABC2ABC21

(
3
3
						

							127
Guía de referencia rápida
Transmisión de mensajes telefax
Coloque el original 
(hasta 10 páginas) cara 
abajo en el alimentador 
de documentos.
Marcación normal  
1.
Levante el auricular u oprima: .
2.
Marque el número de telefax. 
3.
Espere hasta escuchar el tono de 
recepción (si contestara una persona, 
pídale oprimir su tecla Start). 
4. Oprima: .
Marcación automática
1. Oprima la tecla de flecha   o   
hasta que en el visor aparazca el destino 
deseado.
2. 
Oprima: .
Marcación directa por teclado  
1.
Marque el número de fax. 
2.Oprima: .
Grabacion de un mensaje de 
bienvenida
1. Oprima la tecla  , oprima   hasta 
que en el visor aparezca el mensaje de 
bienvenida deseado y, a continuación, 
oprima  una vez.
 
2. Levante el auricular, 
oprima la tecla  
 y hable en el microtel
éfono.
3. 
Oprima la tecla   cuando haya 
finalizado.
SPEAKER
START/MEMORY
START/MEMORY
START/MEMORY
REC/
MEMO
START/MEMORY
STOP
Recepción de mensajes telefax
Oprima  hasta que la flecha que 
hay en el display señale hacia el número de 
recepción deseado
Modo FAX: El aparato telefax contesta y 
transmite automáticamente mensajes telefax.
Modo TEL: Responda a todas las llamadas 
(incluso mensajes de fax), levantando el 
auricular. Para iniciar la recepción de fax, 
oprima
 .
Modo TAD: 
Seleccione este modo cuando 
salga para recibir tanto mensajes hablados 
como telefax.
Memorizar números marc. 
automática
1. Oprima  una vez y  dos veces.
2.Introduzca el número de telefax/teléfono 
completo.
3.Oprima: .
4. 
Ingrese el nombre oprimiendo las teclas 
numéricas. (Para ingresar sucesivamente 
dos letras que requieren la misma tecla, 
oprima
  después de ingresar la 
primera letra).
5. Oprima  y luego .
RESOLUTION/
RECEPTION MODE
START/MEMORY
FUNCTION
START/MEMORY
START/MEMORYSTOP
FAX TELJAN-02 10:30
FAX TELJAN-02 10:30
FAX TELJAN-02 10:30TAD
TAD TAD
RESOLUTION/
RECEPTION MODE
A =B =
C =
D =E =F =
G =H =I  =J =K =L =M =
N =O =P =Q =R =S =T =
U =V =W =X =Y =Z =
SPACE =

(
3
3
						

							128
Uso del teléfono inalámbrico
Hacer una llamada
1. Descuelgue el teléfono inalámbrico y 
oprima .
2. Marque los números cuando escuche el 
tono de línea.
3. Oprima   cuando esté listo para 
finalizar la llamada.  
Hacer una llamada usando la función de 
marcación automática
1. Oprima una vez  .
2. Oprima   o   para seleccionar el 
list
ín. 
3. Oprima   o   hasta que en el 
display aparezca el número que desea 
llamar.
4. Oprima  .
Recibir una llamada
1. Cuando suene el timbre del teléfono 
inalámbrico, descuélguelo y oprima una 
tecla cualquiera para contestar.
2. Oprima   cuando esté listo para 
finalizar la llamada.
Recibir un mensaje telefax usando el 
teléfono inalámbrico
Si después de atender una llamada con el 
teléfono inalámbrico escucha el tono de 
telefax o si el interlocutor desea remitirle 
un mensaje telefax, oprima  .
TALK
OFFOFF
SEARCH
TALK
OFFOFF
START
Memorizar números para marcación 
automática
1. Oprima la tecla  ,   o   
para seleccionar el list
ín y, a continuación, 
. 
2. Introduzca el número de teléfono/telefax 
completo.
Para borrar un error, oprima  .
Para introducir una pausa, oprima  .
3. Oprima   .
4. Introduzca un nombre mediante 
pulsación de las teclas numéricas.
(Para introducir dos letras consecutivas 
que requieran el mismo código, oprima 
 después de introducir la primera 
letra.
5. Oprima   y, a continuación, .
Escuchar los mensajes
1. Oprima .
(Para el buzón general, oprima   ).
2. Oprima   para escuchar todos sus 
mensajes o   para escuchar sólo los 
mensajes nuevos.  
3. Mientras hace la escucha puede pulsar 
, , , 
o .
4. Pulse   cuando haya terminado.  
SEARCH
FUNCTION
/PAUSE
ERASE
HOLD
FUNCTION
/PAUSE
START
STARTOFFOFF
REMOTE
/FLASH
0
PQRS7PLAY
TUV8PLAY NEW
REPEAT0SKIPDELETE
STOPWXYZ9
OFFOFF
A =B =
C =
D =E =F =
G =H =I  =
J =
K =L =
M =
N =O =
P =
Q =R =S =
T =U =
V =
W =
X =Y =Z = SPACE =WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9WXYZ9TUV8
TUV8
TUV8TUV8TUV8TUV8
PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7PQRS7MNO6MNO6MNO6MNO6MNO6
JKL5JKL5JKL5MNO6
JKL5JKL5JKL5GHI4GHI4GHI4GHI4GHI4GHI4
DEF3DEF3DEF3DEF3DEF3DEF3ABC2ABC2ABC2ABC2ABC2ABC21

(
3
3