Samsung LE 32C650 User Manual

							21English
03
Basic Features
Picture In Picture ( ¦PIP)
PIP t
Watches simultaneously the TV tuner and one external video source. PIP (Picture-in-Picture) does not function in the same mode. 
NOTE ✎
If you turn the T V off while watching in  xPIP mode, the PIP window will disappear.
You may notice that the picture in the PIP window  xbecomes slightly unnatural when you use the main screen to view a game or karaoke.
While  xInternet@TV is in operation, the PIP function cannot be used.
PIP settings x
Main pictureSub picture
Component, HDMI1/DVI, HDMI2, HDMI3, HDMI4, PCTV
PIP (Off / On) ■: Activate or deactivate the PIP function.
Channel ■: Select the channel for the sub-screen.
Size ( ■Õ / Ã): Select a size for the sub-picture.
Position ( ■à / – / — / œ): Select a position for the sub-picture.
Sound Select (Main / Sub) ■: You can choose the desired sound (Main / Sub) in PIP mode.
Support Menu
Self Diagnosis
Self Diagnostic might take few seconds, this is part of the normal operation of the TV.
Picture Test (Yes / No) ■: Use to check for picture problems and if the problem continues to occur check the colour pattern. 
Sound Test (Yes / No) ■: Use the built-in melody sound to check for sound problems. 
If you hear no sound from the T V’s speakers,  ✎before performing the sound test, make sure Speaker Select is set to T V speaker in the Sound menu.
The melody will be heard during the test even if  ✎Speaker Select is set to External Speaker or the sound is muted by pressing the MUTE button.
Signal Information ■: (digital channels only) HDTV channel’s reception quality is either perfect or the channels are unavailable. Adjust your antenna to increase signal strength. 
Troubleshooting ■: If the TV seems to have a problem, refer to this description.
If none of these troubleshooting tips apply, contact  ✎the Samsung customer service centre.
Software Upgrade
Software Upgrade can be performed via a broadcasting signal or by downloading the latest firmware from samsung.com to a USB memory device.
Current Version the software already installed in the TV.  
Software is represented as “Year/Month/Day_Version”. ✎
Software Upgrade
Current Version 2010/01/18_000001
U Move    E Enter    R return
By USB 
  ►
By Online
By Channel
Standby Mode Upgrade    : 2 hours later
Alternative Software          ----/--/--_------
Installing the Latest Version
By  ■USB: Insert a USB drive containing the firmware upgrade file, downloaded from www.samsung.com, into the TV. Please be careful not to disconnect the power or remove the USB drive until upgrades are complete. The TV will be turned off and on automatically after completing the firmware upgrade. When software is upgraded, video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can easily reset them after the upgrade.
BN68-02631G_Eng.indb   212010-03-03   �� 8:38:17 
						

							22English
Basic Features
By Online ■: Upgrade the software using the Internet.
First, configure your network. For detailed  ✎procedures on using the Network Setup, refer to the “Network Connection” instructions.
If the Internet connection does not operate  ✎properly, the connection may be broken. Please retry downloading. If the problem persists, download by USB and upgrade.
By Channel ■: Upgrade the software using the broadcasting signal.
If the function is selected during the software  ✎transmission period, software will be automatically searched and downloaded. 
The time required to download the software is  ✎determined by the signal status.
Standby Mode Upgrade ■: A manual upgrade will be automatically performed at selected time. Since the power of the unit is turned on internally, the screen may be turned on slightly for the LCD product. This phenomenon may continue for more than 1 hour until the software upgrade is complete.
Alternative  ■Software (backup): Displays the Software version downloaded through By Online. During the software upgrading, When the Upgrade will discontinue from last step, this function be activated.
HD Connection Guide
Refer to this information when connecting external devices to the TV.
Contact Samsung
View this information when your TV does not work properly or when you want to upgrade the software. You can find information regarding our call centres, and how to download products and software.
BN68-02631G_Eng.indb   222010-03-03   �� 8:38:17 
						

							23English
04
Advanced Features
Display Modes (D-Sub and HDMI/DVI Input)
Optimal resolution is 1920 X 1080 @ 60 Hz
ModeResolutionHorizontal Frequency (KHz)Vertical Frequency (Hz)Pixel Clock Frequency (MHz)Sync Polarity (H / V)
IBM640 x 35031.46970.08625.175+/-720 x 40031.46970.08728.322-/+
MAC640 x 48035.00066.66730.240-/-832 x 62449.72674.55157.284-/-1152 x 87068.68175.062100.000-/-
VESA CVT
720 x 57635.91059.95032.750-/+1152 x 86453.78359.95981.750-/+1280 x 72056.45674.77795.750-/+1280 x 96075.23174.857130.000-/+
VESA DMT
640 x 48031.469 59.94025.175 -/-640 x 48037.86172.80931.500-/-640 x 48037.50075.00031.500-/-800 x 60037.87960.31740.000+/+800 x 60048.07772.18850.000+/+800 x 60046.87575.00049.500+/+1024 x 76848.36360.00465.000-/-1024 x 76856.47670.06975.000-/-1024 x 76860.02375.02978.750+/+1152 x 86467.50075.000108.000+/+1280 x 102463.98160.020108.000+/+1280 x 102479.97675.025135.000+/+1280 x 80049.70259.81083.500-/+1280 x 80062.79574.934106.500-/+1280 x 96060.00060.000108.000+/+1280 x 72045.00060.00074.250+/+1360 x 76847.71260.01585.500+/+1440 x 90055.93559.887106.500-/+1440 x 9001600 X 120070.63575.00074.98460.000136.750162.000-/++/+1680 x 105065.29059.954146.250-/+
VESA GTF1280 x 720 52.500 70.00089.040-/+ 1280 x 102474.62070.000128.943-/-VESA DMT / DTV CEA1920 x 1080p67.500 60.000148.500 +/+
NOTE ✎
For HDMI/DVI cable connection, you must use the  xHDMI IN 1(DVI) jack.
The interlace mode is not supported. x
The set might operate abnormally if a non-standard video format is selected. x
Separate and Composite modes are supported. SOG(Sync On Green) is not supported. x
Connecting to a PC
Using an HDMI/DVI Cable / a D-sub Cable
Advanced Features
R-AUDIO-LPRPBY
AUDIO OUT
R-AUDIO-LPRPBY
AUDIO OUT
R-AUDIO-LPRPBY
DVI OUT
R-AUDIO-LPRPBY
PC OUT
BN68-02631G_Eng.indb   232010-03-03   �� 8:38:19          
						

							24English
Advanced Features
Network Connection
You can set up your TV so that it can access the Internet through your local area network (LAN) using a wired or wireless connection.
Connecting to a Wired Network ¦
You can attach your TV to your LAN using cable in three ways:
You can attach your TV to your LAN by connecting the LAN port on the back\
 of your TV to an external modem using a Cat  yyy5 cable. See the diagram below.
You can attach your TV to your LAN by connecting the LAN port on the back\
 of your TV to a IP Sharer which is connected  yyyto an external modem. Use Cat 5 cable for the connection. See the diagram below.
Depending on how your network is configured, you may be able to attach your TV to your LAN by connecting the LAN \
 yyyport on the back of your TV directly to a network wall outlet using a Cat 5 cable. See the diagram belo\
w. Note that the wall outlet is attached to a modem or router elsewhere in your house.
If you have a Dynamic Network, you should use an ADSL modem or router that supports Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS values your TV needs to access the Internet so you do not have to enter them manually. Most home networks are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you must enter the IP address, subnet mask, gateway, and DNS values manually on your TV’s Cable Setup Screen when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, contact your Internet Service Provider (ISP). If you have a Windows computer, you can also get these values through your computer.
You can use ADSL modems that support DHCP if your network requires a Static IP address. ADSL modems that  ✎support DHCP also let you use Static IP addresses.For information on the procedures to use a static IP address, contact your Internet Service Provider.
The Modem Port on the WallExternal Modem(ADSL / VDSL / Cable TV)TV Rear Panel
LAN CableModem Cable
The Modem Port on the WallExternal Modem(ADSL / VDSL / Cable TV)IP Sharer(having DHCP server)TV Rear Panel
LAN CableLAN CableModem Cable
The LAN Port on the WallTV Rear Panel
LAN Cable
BN68-02631G_Eng.indb   242010-03-03   �� 8:38:20 
						

							25English
04
Advanced Features
Network Setup (Auto)
Use the Automatic Network Setup when connecting your TV to a network that supports DHCP. To set up your TV’s cable network connection automatically, follow these steps:
How to set up automatically
1.   Connect your TV to your LAN as described in the previous section.
2.   Turn on your TV, press the Menu button on your remote, use the ▲ or ▼ button to select Setup, and then press the ENTERE button.
3.   Use the ▲ or ▼ button to select Network in the Setup menu, and then press the ENTERE button. The Network screen appears.
4. On the Network screen, select Network Type.
5.  Set Network Type to Wired.
6.   Select Network Setup. The Network Setup screen appears.
 
7. Set Internet Protocol Setup to Auto.
8.  Auto acquires and enters the needed Internet values automatically.
9.   Wait two minutes, and then press the RETURN button on your remote.
10.  If the Network Function has not acquired the network connection values, go to the directions for Manual.
Network Setup (Manual)
Use the Manual Network Setup when connecting your TV to a network that requires a Static IP address.
Getting the Network Connection Values
To get the Network connection values on most Windows computers, follow these steps:
1.  
Right click the Network icon on the bottom right of the screen.
2. In the pop-up menu that appears, click Status.
3.   On the dialog that appears, click the Support tab.
4.    On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
To set up your TV’s cable network connection manually, follow these steps:
1.    Follow Steps 1 through 6 in the “How to set up automatically” procedure.
2.  Set Internet Protocol Setup to Manual.
3.    Press the ▼ button on your remote to go to the first entry field.
4.    Enter the IP Address, Subnet Mask, Gateway, and DNS Server values. Use the number buttons on your remote to enter numbers and the arrow buttons to move from one entry field to another.
5.  When done, press the RETURN button on your remote.
6.    Select Network Test to check the Internet connectivity.
Network
Network Type   : Wired    ►
Network Setup
Network test
SWl(Samsung Wireless link)  : Off
SWl connect
U Move    E Enter    R return
Network Setup
Internet Protocol Setup  : Auto     ►
   IP Address  :       
   Subnet Mask :       
   Gateway :       
DNS  : Auto
   DNS Server  :       
U Move    E Enter    R return
BN68-02631G_Eng.indb   252010-03-03   �� 8:38:20 
						

							26English
Advanced Features
Connecting Wireless Network ¦
To connect your TV to your network wireless, you need a wireless router or modem and a Samsung Wireless LAN Adapter (WIS09ABGN), which you connect to your TV’s back or side panel USB jack. See the illustration below.
Samsung’s Wireless LAN adapter is sold separately and is offered by select retailers, Ecommerce sites and Samsungparts.com. Samsung’s Wireless LAN adapter supports the IEEE 802.11A/B/G and N communication protocols. Samsung recommends using IEEE 802.11N. When you play video over a IEEE 802.11B/G \
connection, the video may not play smoothly.
NOTE ✎
You must use the “Samsung Wireless L AN Adapter” (WIS09ABGN) to use a wireless network. x
Samsung’s Wireless L AN adapter is sold separately. The WIS09ABGN Wireless L AN adapter is offered by select  xretailers, Ecommerce sites and Samsungparts.com.
To use a wireless network, your T V must be connected to a wireless IP sharer. If the wireless IP sharer supports  xDHCP, your T V can use a DHCP or static IP address to connect to the wireless network.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer  xis currently being used by another device nearby, this will result in interference and communication failure.
If you apply a security system other than the systems listed blow, it will not work with the T V. x
If Pure High-throughput (Greenfield) 802.11n mode is selected and the Encryption type is set to WEP, TKIP or  xTKIPAES (WPS2Mixed) for your AP, Samsung T Vs will not support a connection in compliance with new Wi-Fi certification specifications.
If your AP supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button  xConfiguration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode.
Keep the Samsung Wireless L AN Adaptor at a distance from the T V. If you watch the T V with the adaptor connected  xnearby, images may appear corrupted for some channels.
If your router, modem, or device is not, it may not connect to the T V via the “Samsung Wireless L AN Adapter.” x
Connection Methodsxx x: You can setup the wireless network connection on six ways.
–  Configuration
–  PBC (WPS)
–  Auto Setup (Using the Auto Network Search function)
–  Manual Setup
–  SWL (Samsung Wireless Link)
–  Ad-Hoc
All of Samsung Wireless LAN Adapter shoud be connected directly to the TV’s USB port. USB HUB are not supported. x
or
The LAN Port onthe Wall
LAN Cable
Wireless IP sharer
Samsung WirelessLAN Adapter
TV Side Panel
BN68-02631G_Eng.indb   262010-03-03   �� 8:38:21 
						

							27English
04
Advanced Features
Network Setup  
(Samsung Auto Configuration)
This function is available in APs (Access Points) that support Samsung Auto Configuration. If there is no such AP, you can connect through PBC (WPS) or manually.
This function is available when  ✎SWL(Samsung Wireless Link) set to Off.
You can check for equipment that supports Samsung  ✎Auto Configuration on www.samsung.com.
How to set up using Samsung Auto Configuration
1. Place the AP and TV next to each other and turn them on.
Because the booting times of applications differ,  ✎you may have to wait for approximately 2 minutes.
If the L AN cable connected the WAN port of AP  ✎during Samsung Auto Configuration, you are able to complete until Internet connection test. If you do not connect, Samsung Auto configuration will check only
2.   After 2 minutes, connect the Samsung Wireless LAN Adaptor to the TV. When the Samsung Wireless LAN Adaptor is established, the pop-up window appears.
3.   As soon as a connection is established, place the AP in parallel with the Samsung Wireless LAN Adaptor giving a gap no larger than 25cm.
4. Wait until the connection is automatically established.
If the connection fails, reset the AP and then try  ✎again.
If Samsung Auto Configuration does not connect  ✎your T V to your AP, a pop-up window appears on the screen notifying you of the failure. Reset the AP, and then try again. If the connection fails again, choose one of the other connection setup methods, PBC (WPS), auto, or manual.
5.   After the connection is established, locate the sharer at the desired location.
If the AP settings have been changed or it is the  ✎first time you use the new AP after purchase, you need to set up again beginning from Step 1.
Network Setup (PBC (WPS))
How to set up using PBC (WPS)
If your router has a PBC (WPS) button, follow these steps:
1.   Connect your TV to your LAN as described in the previous section.
2.   Turn on your TV, press the MENU button on your remote, use the ▲ or ▼ button to select Setup, and then press the ENTERE button.
3.   Use the ▲ or ▼ button to select Network in the Setup menu, and then press the ENTERE button.
4. On the Network screen, select Network Type.
5. Set Network Type to Wireless.
6.   Select Network Setup. The Network Setup screen appears.
7. Press the Red button on your remote.
8.    Press the PBC (WPS) button on your router within 2 minutes. Your TV player automatically acquires all the network setting values it needs and connects to your network.
9.   After the network connection is set up, press the RETURN button to exit the Network Setup screen.
Network Setup (Auto)
Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Security Key. The Security Key is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked to enter when you set up security for your wireless network. If you use this method of setting up the network connection, and have a Security Key for your wireless network, you will have to enter the Pass Phrase during the setup process.
How to set up automatically
To set up the wireless connection automatically, follow these steps:
1.   Follow Steps 1 through 6 in the “How to set up PBC (WPS)” above.
2.   Press the ▼ button to select Internet Protocol Setup, and then press the ENTERE button. Press the ▲ or ▼ button to select Auto, and then press the ENTERE button.
Network Setup
Select a network   : Not Selected ►Internet Protocol Setup : Auto 
   IP Address  :       
   Subnet Mask :       
   Gateway :       DNS  : Auto
   DNS Server  :       
U Move    E Enter    R return
BN68-02631G_Eng.indb   272010-03-03   �� 8:38:22 
						

							28English
Advanced Features
3.   Press the ▲ button to go to Select a Network, and then press the ENTERE button. The Network function searches for available wireless networks. When done, it displays a list of the available networks.
4.   In the list of networks, press the ▲ or ▼ button to select a network, and then press the ENTERE button.
If the AP is set to Hidden (Invisible), you have  ✎to select Add Network and enter the correct Network Name (SSID) and Security Key to establish the connection.
5.   If the Security/PIN pop-up appears, go to Step 6. If the Network Connecting Screen appears, go to Step 10.
6.   Press the ▲ or ▼ button to select Security or PIN. For most home networks, you would select Security (for Security Key). The Security Screen appears.
ABCDEFG
HIJKLMN
OPQRSTU
VWXYZ
0~9
BC
Network Setup
U Move    E Enter    R return
Secunity Key
0 enteredNumber
Lower case
Delete
Space
7.    On the Security screen, enter your network’s Pass Phrase.
You should be able to find the Pass Phrase on  ✎one of the set up screens you used to set up your router or modem.
8.   To enter the Pass Phrase, follow these general directions:
–    Press the number buttons on your remote to enter numbers.
–   Use the direction buttons on your remote to move from button to button on the Security Key screen.
–   Press the Red button to change case or display symbols/characters.
–   To a enter letter or symbol, move to the letter or symbol, and then press the ENTERE button.
–   To delete the last letter or number you entered, press the Green button on your remote.
9.    When done, press the Blue button on your remote. The Network Connecting screen appears.
10.  Wait until the connection confirmation message is displayed, and then press the ENTERE button. The Network Setup screen re-appears.
11.   To test the connection, press the RETURN button to select Network Test, and then press the ENTERE button.
Network Setup (Ad-Hoc)
You can connect to a mobile device without an access point through the “Samsung Wireless LAN Adapter” by using a peer to peer network.
 This function is available when  ✎SWL(Samsung Wireless Link) is set to Off.
How to connect to new Ad-hoc
1.   Follow Steps 1 through 6 in the “How to set up using PBC (WPS)”. (P. 27)
2.   Choose Select a network. A list of devices/networks appears.
3.   While in the device list, press the Blue button on the remote.
The message  ✎Ad-hoc is a direct WI-Fi connection with cellphone or PC. The existing network system may have limited functionality. Do you want to change the network connection? is displayed.
4.   Input the generated Network Name (SSID) and Security Key into the device you want to connect.
How to connect an existing Ad-hoc device
1.   Follow Steps 1 through 6 in the “How to set up using PBC (WPS)”. (P. 27)
2.   Choose Select a network. Then, the device list will be displayed.
3. Select the device you want in the Device list.
4. If security key was applied, input the security key.
If network does not operate normally, check  ✎the Network Name (SSID) and Security Key again. An incorrect Security Key may cause a malfunction.
Network Setup (Manual)
If the other methods do not work, you need to enter the Network setting values manually.
Getting the Network Connection Values
To get the Network setting values on most Windows computers, follow these steps:
1.   Right click the Network icon on the bottom right of the screen.
2. In the pop-up menu, click Status.
3. On the dialog that appears, click the Support tab.
4.   On the Support tab, click the Details button. The Network settings are displayed.
BN68-02631G_Eng.indb   282010-03-03   �� 8:38:22 
						

							29English
04
Advanced Features
How to set up manually
To enter the Network settings into your TV, follow these steps:
1.   Follow Steps 1 through 6 in the “How to set up using PBC (WPS)”. (P. 27)
2.   Press the ▼ button to select Internet Protocol Setup, and then press ENTERE button. Press the ▲ or ▼ button to select Manual, and then press ENTERE button.
3.   Press the ▼ button to go to the first entry field (IP Address).
4. Use the number buttons to enter numbers.
5.   When done with each field, use the ► button to move successively to the next field. You can also use the other arrow buttons to move up, down, and back.
6.   Enter the IP Address, Subnet Mask, and Gateway values.
7. Press the ▲ or ▼ button to go to DNS.
8.   Press the ▼ button to go to the first DNS entry field. Enter the numbers as above.
9.   When done, press the ▲ button to go to Select a Network. Select your network, and then press ENTERE button.
10.  Go to Step 4 in the “How to set up automatically” (P. 27), and follow the directions from that point on.
Network Setup 
(SWL (Samsung Wireless Link))
This function lets you connect a Samsung device that supports the PBC (WPS) to your TV. You can connect devices to the TV even if a sharer is not connected to the TV.
To use the Internet@T V, the AP (access point) must be  ✎connected to the wireless network.
If a Samsung Wireless Lan Adapter is connected to the  ✎USB 2 port, the network may not operate normally. We recommend to connect to USB 1 (HDD) por t.
Only sharers using the 2.4 Ghz band are supported.   ✎Sharers using the 5 Ghz band are not supported.
SWL connect
You can directly connect a device that supports the PBC (WPS) to the TV.
This function is available when  ✎SWL(Samsung Wireless Link) is set to On.
How to connect Samsung Wireless link
For the procedures to establish a connection, refer to the following:
1.    Follow Steps 1 through 5 in the “How to set up using PBC (WPS)”. (P. 27)
2.   Select Samsung Wireless Link by using the ▼ button and press the ENTERE button to turn it On.
3.   Select SWL connect by using the ▼ button and press the ENTERE button.
4.   If the “Press the PBC button on the device which supports PBC button to connect within 120 seconds” message appears, press the PBC button on the device to connect.
For more information, refer to the wireless network  ✎setup manual of the device to be connected.
5.   If the device is connected properly to the TV after starting count on message box then message box will be disappeared automatically.
If the connection fails, please retry after 2 minutes. ✎
If Your TV Fails to Connect to the Internet
Your TV may not be able to connect to the Internet because your ISP has permanently registered the MAC address (a unique identifying number) of your PC or modem, which it then authenticates each time you connect to the Internet as a way of preventing unauthorized access. As your TV has a different MAC address, your ISP can not authenticate its MAC address, and your TV can not connect.
To resolve this problem, ask your ISP about the procedures required to connect devices other than a PC (such as your TV) to the Internet.
If your Internet service provider requires an ID or password to connect to the Internet, your TV may not be able to connect to the Internet. If this is the case, you must enter your ID or password when connecting to the Internet.
The internet connection may fail because of a firewall problem. If this is the case, contact your Internet service
provider.
If you cannot connect to the Internet even after you have followed the procedures of your Internet service provider, please contact Samsung Electronics.
BN68-02631G_Eng.indb   292010-03-03   �� 8:38:22 
						

							30English
Advanced Features
Media Play
Connecting a  ¦USB Device
1. Turn on your TV.
2. Connect a USB device containing photo, music and/or movie files to the\
 USB 1 (HDD) or USB 2 jack on the side of the TV.
3. When USB is connected to the TV, popup window appears. Then you can select Media Play.
 ¦Connecting to the PC through network
You can play pictures, music and videos saved on your PC or on your TV through a network connection in the Media Play mode.
 
If you use  ✎Media Play through saved file on your PC, you should download “PC Share Manager” and users manual from “www.samsung.com.”  
1. For more information on how to configure your network, refer to ‘Network Connection’.
You are recommended to locate both TV and PC in same subnet. The first 3 parts \
of the subnet address of the TV and  –the PC IP addresses should be the same and only the last part (the host address) should be changed. (e.g. IP Address: 123.456.789.**)
2. Using a LAN cable, connect between the external modem and the PC onto which the Samsung PC Share Manager program will be installed.
You can connect the TV to the PC directly without connecting it through a Sharer (Router). –
Enjoy photos, music and/or movie files saved on a USB Mass Storage Class (MSC) device and/or your PC.
External Modem (ADSL/VDSL/Cable TV)
LAN Cable
Wireless IP sharer
PCTV Side Panel
Samsung Wireless LAN Adapter
LAN
or
SUM Change Device View Devices    E Enter    R return
MediaPlay
Videos
USB Drive
TV Side Panel
or
BN68-02631G_Eng.indb   302010-03-03   �� 8:38:24