Panasonic Pv Gs50 Operating Instructions Manual

							41
ªMulti-Picture Mode
Strobe Multi-Picture Mode 1:
You can capture and record 9 consecutive small still pictures.
Manual Multi-Picture Mode 
2:
You can manually capture and record 9 small still pictures.
After setting [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >> 
[EFFECT1] >> [MULTI].....
1Set [MULTI-PICTURES] >> [SCAN MODE] >> 
[STROBE] or [MANUAL].
When [STROBE] is selected:
≥Set the [SPEED] to a desired strobe speed.
[FAST]: You can capture 9 consecutive still pictures 
within approximately 1 second
[NORMAL]: You can capture 9 consecutive still pictures 
within approximately 1.5 seconds
[SLOW]:You can capture 9 consecutive still pictures 
within approximately 2 seconds
≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to 
[ON], the intervals at which the 9 still pictures are taken are 
longer at the beginning and end than in the middle of the swing 
strobe period, and it is useful for analyzing swing motion, etc., 
in sports.
When [MANUAL] is selected:
≥You can select a desired scene one at a time up to 9 small 
pictures.
2Exit the menu by pressing the [MENU] Button.
3Press the [MULTI] Button.
≥If [MANUAL] is selected, press the [MULTI] Button at each 
scene you want to capture.
4Press the Recording Start/Stop Button or the 
[PHOTO SHOT] Button to record on the Cassette.
Deleting all the captured Multi-Pictures
While 9 multi-pictures are displayed, press the [MULTI] Button.
≥If [MANUAL] has been selected, press the [MULTI] Button after 
9 pictures are displayed.
To Display the Multi-Pictures again
Press the [MULTI] Button for 1 second or longer.
To Delete Multi-Pictures one by one
(When pictures were captured in [MANUAL])
When the [MULTI] Button is pressed for 1 second or longer while the 
still pictures are displayed, the picture captured last is deleted. If you 
keep pressing the [MULTI] Button, the pictures are deleted 
continuously.
≥After still pictures are deleted, they cannot be displayed again.
≥For other notes, see page 87.
1
21, 24
MENUPUSHMF / VOL / JOG W.B / SHUTTER / IRIS
PHOTO
SHOT
4
MULTI
P-IN-P3
CAMERA
PV-GS50P.book  41 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							42
VCR Mode
Playing Back
The recorded scene can be played back immediately after 
recording.
1Rotate the [OFF/ON/MODE] Switch and set the 
Palmcorder in the VCR Mode.
≥The [VCR] Lamp lights up. 1
2
Press the [6] Button to rewind the tape.
≥Rewind the tape to the point where you want to start playback.
≥When the tape reaches the beginning, rewinding stops 
automatically.
3Press the [1] Button to start playback.
To Stop Playback
Press the [∫] Button 2.
≥If a cassette recorded with copyright protection signals is played 
back, the screen becomes blue or mosaic-like noise patterns 
appear.
ªAdjusting the Sound Volume
Until the [VOLUME] Indication 3 appears, keep pressing the 
[PUSH] Dial 
4. Then, rotate the [PUSH] Dial to adjust the volume. 
After the adjustment, press the [PUSH] Dial to make the [VOLUME] 
Indication disappear.
To adjust the volume with the Remote Controller, press the [T] or [W] 
Button to display the [VOLUME] Indication. Press the [T] Button to 
increase the volume or press the [W] Button to decrease the volume. 
The [VOLUME] Indication goes off 2 or 3 seconds after the 
adjustment is finished.
≥When the Playback Zoom Function is in use, the sound volume 
cannot be adjusted.
≥For other notes, see page 88.
3
1
14
CAMERAVCRCARD
P. B
OFFONMODE
PUSHMF / VOL / JOG W.B / SHUTTER / IRIS
SEARCHBACK
LIGHT
FADEMAGIC
PIX
3
2 2
PV-GS50P.book  42 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							43
Finding a Scene You Want to Play Back
ªCue/Review Playback
Cue Playback A
Press the [5] Button 1 during playback.
Review Playback B
Press the [6] Button 2 during playback.
≥If the Button is held continuously, it remains as Cue Playback or 
Review Playback until you release it.
ªHyper Check Function
If you press the [5] Button during fast-forwarding of the tape or the 
[6] Button during rewinding of the tape, Cue Playback or Review 
Playback continues for as long as the Button is held down.
ªVariable Speed Search Function
The speed of Cue Playback or Review Playback can be varied.
1During playback, press the [1] Button.
≥[1k!] Indication appears. C
2
Rotate the [PUSH] Dial and select a desired search 
speed.
The following 6 playback speeds are available for the Variable Speed 
Search Function in both the fast-forwarding and rewinding directions. 
1/5k (slow playback, SP mode only), 1/3k (slow playback, LP mode 
only),1k, 2k, 5k, 10k, and 20k.
≥The same setting can be performed using the Remote Controller’s 
[VAR.SEARCH] Button, the [π] Button and the [∫] Button.
Resuming Normal Playback
Press the [1] Button.
≥During Cue or Review Playback, fast-moving images may show 
mosaic-like noise patterns. This is not a malfunction.
≥The sound is muted during search.
≥The Variable Speed Search feature is not available when the 
Repeat playback is active.
ªRepeat Playback
If you hold down the [1] Button for 5 seconds or longer, the 
Palmcorder switches to Repeat Playback Mode, and the [R !] 
Indication appears
 D. (To cancel Repeat Playback Mode, set the 
[OFF/ON/MODE] Switch to [OFF].)
C
A
B
D
2
R
PUSHMF / VOL / JOG W.B / SHUTTER / IRIS
SEARCH SEARCHBACK
LIGHT
1 21
VCR
PV-GS50P.book  43 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							44
Slow Motion Playback
This Palmcorder can play back at a slow speed.
1Press the [1] Button.
2Press the [E] Button or the [D] Button on the Remote 
Controller.
≥When the [E] Button is pressed, Slow Motion Playback 
proceeds in the reverse direction, while pressing the [D] 
Button starts Slow Motion Playback in the forward direction.
Scenes recorded in the SP mode are played back at approximately 
1/5th of the normal speed.
Scenes recorded in the LP mode are played back at approximately 
1/3rd of the normal speed.
Resuming Normal Playback
Press the [1] Button.
~~~~~~~~~~~~~~~~~~~~~~
Still Playback/Still Advance Playback
This Palmcorder is capable of still picture playback and 
frame-advance playback.
1Press the [1] Button.
2Press the [;] Button.
≥The playback image stops in the Still Playback Mode.
3Press the [E] Button or the [D] Button on the Remote 
Controller.
≥With each press of the [E] Button, still pictures advance in the 
reverse direction. With each pressing of the [
D] Button, still 
pictures advance in the forward direction. If either one of the 
buttons is pressed continuously, still pictures advance 
continuously one frame at a time until the button is released.
Resuming Normal Playback
Press the [1] Button or [;] Button.
ªJog Playback
By rotating the Jog Dial ([PUSH] Dial) 1 of the Palmcorder in the 
Still Playback Mode, still pictures can be advanced one frame at a 
time in the forward or reverse direction.
≥If the Palmcorder is left in the Still Playback Mode for more than 
5 minutes, the Palmcorder switches to the Stop Mode to protect 
the video heads from excessive wear and tear.
1
2 1
33
ZOOM
INDEX INDEX
SELECTSTORESTOP
KL∫
OSDCOUNTER
V/REWSTILL ADV
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSEFF/W
STILL ADV
MENU
61 5;ED
VAR.
SEARCHP.B.
ZOOM
PUSHMF / VOL / JOG W.B / SHUTTER / IRIS
1SEARCHBACK
LIGHT
FADESTILL
2
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VA R .
SEARCHP.B.
ZOOM
1
22
PV-GS50P.book  44 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							45
BLANK11
MENUPUSHMF / VOL / JOG W.B / SHUTTER / IRIS
Finding the End of a Recording (Blank Search Function)
The Blank Search Function helps you to locate the end of a 
recording on the Cassette quickly.
1Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] 
>> [BLANK SEARCH] >> [YES].
≥The [BLANK] Indication 1 appears.
≥Approximately 1 second before the last recorded scene, the 
Palmcorder switches to the Still Playback Mode.
≥If there is no blank portion left on the cassette, the Palmcorder 
stops at the end of the tape.
Canceling Blank Search prior to completion
Press the [∫] Button.
~~~~~~~~~~~~~~~~~~~~~~Playback Zoom Function
A part of the image can be enlarged up to 10 times during playback.
1During playback, press the [P.B. ZOOM] Button on 
the Remote Controller.
≥The center of the image is enlarged to approximately double 
the size.
Changing the Zoom Magnification
2Change the magnification by pressing the [W] or [T] 
Button on the Remote Controller.
≥You can increase the magnification up to 10k.
Changing the enlarged area of an image
3Press the Arrow Button (π, ∑, ∏, ∫) on the Remote 
controller that points to the area you want to enlarge.
Canceling the Playback Zoom Function
Press the [P.B. ZOOM] Button on the Remote Controller.
≥For other notes, see page 88.
ZOOM 2t
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
2
1
3
VCR
PV-GS50P.book  45 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							46
Index Search Functions
To facilitate searching of desired scene, this Palmcorder 
automatically records index signals during recording, as explained in 
the following.
PhotoShot Index Signal
These signals are automatically recorded whenever still pictures are 
taken in PhotoShot Mode (l 30).
When recording still pictures using the Continuous PhotoShot Mode 
(l 30), the index signal is not recorded.
Scene Index Signal
Scene Index Signals are automatically recorded when you start 
recording after inserting a Cassette.
However, if the Palmcorder is switched from the VCR Mode to 
Camera Mode, or if the date and time is set before the start of 
recording, the index signal is not recorded.
≥If [SCENE INDEX] of [RECORDING SETUP] Sub-Menu on the 
[CAMERA FUNCTIONS] Main-Menu is set to [2HOUR], an index 
signal is recorded when Recording is restarted after a lapse of 
2 hours or longer. If it is set to [DAY], an index signal is recorded 
when recording is restarted after the date has changed since the 
last recording. (While the index signal is recorded, the [INDEX] 
indication 
A flashes for a few seconds.)
ªPhotoShot Index Search
1
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] 
>> [SEARCH] >> [PHOTO].
2Press the [9] Button or the [:] Button on the 
Remote Controller.
≥With each press of the corresponding button, still pictures recorded 
in PhotoShot Mode are searched.
≥After pictures with sounds are played back for 4 seconds, the 
Palmcorder switches to the Still Playback Mode.
ªScene Index Search
1
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] 
>> [SEARCH] >> [SCENE].
2Press the [9] Button or the [:] Button on the 
Remote Controller.
≥When the corresponding button is pressed once, the [S 1] 
Indication B appears, and searching of the subsequent scene 
marked with an index signal starts. Each time the button is pressed 
after the start of Scene Index Search, the indication changes from 
[S 2] to [S 9], and the beginning of the scene corresponding to the 
selected number will be searched. After reaching the desired 
scene, playback starts automatically.
≥Up to 9 scene numbers can be selected.
Top Scan
If the [9] Button or the [:] Button is pressed for more than 
2 seconds, the Palmcorder will scan for scenes (or PhotoShots) and 
play back the first few seconds of each. (To cancel, press the [
1] 
Button 1 or the [∫] Button 2.)
≥For other notes, see page 88.
INDEX
S   1
A
B
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VA R .
SEARCHP.B.
ZOOM2
1
2
1MENUPUSHMF / VOL / JOG W.B / SHUTTER / IRIS
PV-GS50P.book  46 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							47
Playback Digital Effect Functions
During playback, special Digital Effects can be added to the 
Recording. The digital effects that may be applied in the process of 
recording (except Picture in Picture Mode) will be the same as these 
added effects.
1Press the [1] Button.
2Press the [SELECT] Button on the Remote Controller 
and select desired Digital Effect.
≥When the [SELECT] Button is pressed repeatedly, the Digital 
Effect selection changes.
MULTI )WIPE )MIX )STROBE )NEGA )SEPIA )B/W 
)TRAIL ) SOLARI )MOSAIC ) MIRROR
≥The same setting can also be set using the [DIGITAL EFFECT] 
on the [VCR FUNCTIONS] Main-Menu.
Suspending Playback Digital Effect Temporarily
Press the [OFF/ON] Button 1 to suspend or restart the digital 
effect. When the digital effect is paused temporarily, the selected 
effect’s indication flashes.
Canceling the Digital Effect
Press the [SELECT] Button on the Remote Controller repeatedly 
until the Digital Effect Indication is cleared.
≥For other notes, see page 88.
ªPlayback with Wipe Mode and Mix Mode
1
Press the [1] Button to start playback.
2Press the [SELECT] Button on the Remote Controller 
and select [WIPE] or [MIX].
3Press the [STORE] Button for the moment you want 
to save as a still picture.
≥The [WIPE] or [MIX] Indication changes to [B] or [C] 
and the image is saved.
4Press the [OFF/ON] Button in the scene in which you 
want to use the Wipe or Mix effect.
≥The scene changes as a result of the Wipe or Mix effect.
≥The Wipe Function and Mix Function can be used only from the 
Remote Controller during playback.
≥If the [OFF/ON] Button is pressed while Wipe Function or Mix 
Function is used, the effect will stop temporarily at that point. 
Pressing the [OFF/ON] Button again will bring back the effect.
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S E
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
1
2
1
WIPE
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVO Lr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP. B .
ZOOM
1
2
3
4
MIX
VCR
PV-GS50P.book  47 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							48 ªPlaying Back with Multi-Picture Mode 
Strobe Multi-Picture Mode [STROBE] 1:
You can capture 9 consecutive still pictures from playback images.
Manual Multi-Picture Mode [MANUAL] 
2:
Selecting a desired still picture one at a time, you can capture 9 still 
pictures.
Index Multi-Picture Mode ([PHOTO], [SCENE]) 
3:
You can capture 9 screens of pictures to which index signals are 
attached.
After setting [VCR FUNCTIONS] >> [DIGITAL EFFECT] >> 
[EFFECT SELECT] >> [MULTI]...
1Set [MULTI-PICTURES] >> [SCAN MODE] >> 
[STROBE] or [MANUAL] or [PHOTO] or [SCENE], 
whichever mode you prefer.
When [STROBE] is selected:
≥Set the [SPEED] to a desired strobe speed.
[FAST]: You can capture 9 consecutive still pictures 
within approximately 1 second
[NORMAL]:You can capture 9 consecutive still pictures 
within approximately 1.5 seconds
[SLOW]:You can capture 9 consecutive still pictures 
within approximately 2 seconds
≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to 
[ON], the intervals at which the 9 still pictures are taken are 
longer at the beginning and end than in the middle of the swing 
strobe period, and it is useful for analyzing swing motion, etc., 
in sports.
2Exit the Menu by pressing the [MENU] Button.
3Play back the tape.
≥If you select Index mode, it is not necessary to play back the 
tape.
4Press the [MULTI] Button.
≥If [STROBE] is selected: 9 screens are automatically 
captured from the point at which the Button is pressed.
≥If [MANUAL] is selected: press the [MULTI] Button at each 
scene you want to capture. When 9 screens are captured, the 
tape will stop.
≥If [PHOTO] or [SCENE] is selected: From the point at which 
the Button is pressed, 9 screens of pictures to which index 
signals are attached are captured in the playback direction. 
After 9 screens are captured, the tape will stop, but, if there are 
8 or less pictures to be captured, the tape will stop at its end.
Deleting All the Captured Multi-Pictures
While displaying the multi-pictures that have been captured, press 
the [MULTI] Button.
≥If [MANUAL] has been selected, press the [MULTI] Button after 
9 screens are displayed.
To Display the Multi-Pictures again
Press the [MULTI] Button for 1 second or longer.
1
2
3
BACK
LIGHT
FADE
MULTI
P-IN-P4 31, 2
1
MENU
PUSHMF / VOL / JOG W.B / SHUTTER / IRIS
PV-GS50P.book  48 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							49
PUSHMF / VOL / JOGW.B / SHUTTER / IRIS
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
DATE/
TIME
RESET TITLE T
W
sVOLr¥REC MULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
61 5
;ED
VA R .
SEARCHP.B.
ZOOM
1
To Delete Multi-Pictures one by one (When Pictures 
have been captured in Manual Mode)
When the [MULTI] Button is pressed for 1 second or longer while the 
still pictures are displayed, the picture that was captured last is 
deleted. If you continue to press the Button, the pictures are deleted 
consecutively.
≥After still pictures are deleted one at a time, they cannot be 
displayed again.
To Stop Capturing Pictures midway (When Pictures 
have been captured in Index Mode)
Press the [∫] Button.
To Search the tape position of a desired picture among 
the playback pictures displayed on 9 screens
1After displaying pictures in Multi-Picture Mode, 
rotate the [PUSH] Dial to select the image whose tape 
position you want to search.
≥The selected picture is marked with a red frame.
2Press the Index Button [:] or [9] 1 on the 
Remote controller.
≥Still picture playback takes place at the selected picture.
≥For other notes, see page 88.
~~~~~~~~~~~~~~~~~~~~~~Playing Back on Your TV
By connecting your Palmcorder to your TV, the recorded scenes can 
be viewed on your TV screen.
≥Before connecting them, turn off the power of both the Palmcorder 
and TV.
1Connect the [AV IN/OUT] Jack of the Palmcorder to 
the Video and Audio Input Jacks of the TV.
≥Using the A/V Cable 1 (supplied), make a connection with the 
TV. If the TV has an S-Video Jack, connect an S-Video Cable 
(supplied) 
2, too.
≥When plugging the pin plug of the A/V cable into the [AV IN/
OUT] Jack, plug it in as far as it goes.
Making the Indications Appear on the TV screen
Press the [OSD] Button 3 on the Remote Controller.
≥Be sure to select the proper input on your TV. (If necessary, 
consult your TV’s operating instructions.)
≥If you play back a Cassette recorded with copyright protection 
signals, the screen becomes blue or mosaic-like noise patterns 
appear.
≥If you set [AV JACK] on the [AV IN/OUT SETUP] Sub-Menu to [IN/
OUT], nothing will be shown on the TV screen except during 
playback.
≥Picture size may be displayed differently when playing back a 
Cinema picture on a wide-screen TV with [B/W] or [SEPIA] of 
Playback Digital Effect.
ZOOM
SO
OSD
COUNTER
V/REW
STILL ADV
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV61 5
;ED
3
1
AV IN / OUT
PHONES
S-VIDEO
IN / OUT
1
2
[VIDEO IN]
[AUDIO IN] [S-VIDEO IN]
REMOTE / MIC
(PLUG IN POWER)
VCR
PV-GS50P.book  49 ページ  ２００３年２月１７日　月曜日　午後６時３０分 
						

							50
Audio Dubbing
You can add music or narration to the recorded Cassette.
≥If you perform audio dubbing onto a tape that was recorded with 
[AUDIO REC] on the [RECORDING SETUP] Sub-Menu of the 
[CAMERA FUNCTIONS] Main-Menu set to [16bit], the original 
sound is erased.
 (If you want to preserve the original sound, use 
the [12bit] Mode when recording.)
≥Audio Dubbing cannot be performed onto recordings made in LP 
Mode. (l27)
1Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> 
[AV JACK] >> [IN/OUT].
2Continuing the aforesaid setup, select 
[A.DUB INPUT] >> [MIC] or [AV IN].
≥Set to [AV IN] when external device is used, and to [MIC] when 
an external or built-in microphone is used.
3Switch the Palmcorder over to the Still Playback 
Mode where you want to add new sound track.
4Press the [A.DUB] Button on the Remote Controller.
≥[A.DUB;] Indication appears. 1
5
To start Audio Dubbing, press the [;] Button on the 
Remote Controller.
≥[A.DUB!] Indication appears. 2
To Stop Audio Dubbing
Press the [;] Button on the Remote Controller.
The Palmcorder is in the Still Playback Mode again.
To dub audio while listening to a pre-recorded sound
When pausing the audio dubbing, set the [12bit AUDIO] on the 
[PLAYBACK FUNCTIONS] Sub-Menu to [ST2] and you can check 
the pre-recorded sound. When a microphone is used for audio 
dubbing, use headphones to listen to the pre-recorded sound while 
dubbing the audio. (When using headphones, set [AV JACK] on the 
[AV IN/OUT SETUP] Sub-Menu to [OUT/PHONES].) When the line 
input is used, you can dub audio while listening to a pre-recorded 
sound from the speaker.
Playing Back the Sound Recorded with Audio Dubbing
(For 12 bit Audio Recording)
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[12bit AUDIO] >> [ST2] or [MIX].
ST1: Play back only the original sound.
ST2: Play back only the sound added by Audio Dubbing.
MIX: Play back both the original sound and the sound added by 
Audio Dubbing simultaneously.
≥For other notes, see page 88.
A.DUB;
A.DUB!
1
24
3, 5
ZOOM
INDEX INDEX
SELECT
STOPKL∫
OSD
COUNTER
V/REW
STILL ADV
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S E
FF/W
STILL ADV61 5
;ED
VAR.
SEARCHP. B .
ZOOM
1, 2MENUPUSHMF / VOL / JOG W.B / SHUTTER / IRIS
PV-GS50P.book  50 ページ  ２００３年２月１７日　月曜日　午後６時３０分