Panasonic Network Camera Wv Sfv481 Operating Instructions

13.4.3  Configure settings relating to recording to an SD memory
card when an alarm occurs
Click “ SD memory card  >>” of “Camera action on alarm ” on the [ Alarm] tab of the  “Alarm” page. ( ®page 137)
Refer to page 70 for information on configuration for these settings.
Operating Instructions141
13 Configure the alarm settings [Alarm]   

13.4.4  Configure settings relating to Panasonic alarm protocol
notification when an alarm occurs Click “Panasonic alarm protocol notification >>” of “Camera action on alarm” on the [Alarm] tab of the
“Alarm” page. ( ®page 137)
Refer to page 150 for information on configuration for these settings.
142Operating Instructions
13 Configure the alarm settings [Alarm]   

13.4.5  Configure settings relating to HTTP alarm notification when
an alarm occurs Click “HTTP alarm notification >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page.
( ® page 137)
Refer to page 152 for information on configuration for these settings.
13.4.6  Configure settings relating to camera actions on alarm
action Click “Preset action on alarm >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page.
( ® page 137)
IMPORTANT
•Preset action upon alarm detection can...

Select an action to be taken when a terminal alarm 1 is detected from the following.
• Off:  Does not take any action even when a terminal alarm 1 is detected.
• (Quad PTZ) [1-4]/[5-8]/[9-12]/[13-16]:  When using Quad PTZ, all of the 4 screens move to their preset
positions.
• (Single PTZ) 1-16:  If a previously registered preset position is selected, when a terminal alarm 1 is
detected, the camera will move to that position.
• Default:  Off
[Terminal alarm 2]
Select an action to be taken when a terminal...

•Depending on the network environment, notification may be delayed even when  “Real time ” is selected
for “Alarm status update mode” on the [Basic] tab of the “Basic” page ( ®page 62).
• After configuring the VMD area, the VMD area may move out of alignment when the JPEG/H.264
“ Image capture mode ” setting is changed. Make sure to check the VMD area after changing the  “Image
capture mode” setting.
• The motion detection function is not the dedicated function to prevent thefts, fires, etc. We are not...

When “8M Fisheye + Panorama” or “4M Fisheye + Panorama” is selected for “Image capture mode”:
– Fisheye:  Performs video motion detection with Fisheye images.
– Panorama:  Performs video motion detection with Panorama images.
When “8M Fisheye + Double Panorama” or “4M Fisheye + Double Panorama” is selected for “Image
capture mode”:
– Fisheye:  Performs video motion detection with Fisheye images.
– Double panorama:  Performs video motion detection with Double Panorama images.
When “8M Fisheye + Quad PTZ”...

IMPORTANT•“Light detection control” may not work when brightness change is too small.
• When “On” is selected for “Light detection control”, the video motion detection may not be performed
even when detecting a subject moving over the whole screen.
[Area No. notification]
When “Panasonic alarm protocol notification >>” is clicked, the [Notification] tab of the “Alarm” page will be
displayed. ( ®page 149)
VMD information addition [Information addition]
Select “On” or “Off” to determine whether or not to...

1.Set the video motion detection area by dragging the mouse on the screen.
→ The designated area will become the VMD area “1(White)” and the outline will be displayed. When 2
- 4 VMD areas are set, each area will be numbered in order. The areas will be identified by the
respective outline colors. The “Status” of the outline to be set for the area will become “On”.
Note
•When “Fisheye”, “Single PTZ”, or “Panorama” is selected for “Image capture mode”, 4 areas can
be configured.
• When “Double Panorama” is...

•When  “Quad PTZ ” is selected for  “Image capture mode ”, 1 area can be configured for each image.
2. Adjust “Detection area” and “Detection sensitivity” using the slider.
Refer to page 144 for further information about the “Detection sensitivity” and “Detection area”.
The currently displayed area and its detection sensitivity will be displayed in the  “Detection area” section.
Change areas and the settings of “Detection area” and “Detection sensitivity” as necessary.
3. Click the [Set] button after...

13.6.1  Configure the settings relating to Panasonic alarm protocol
Panasonic alarm protocol notification[Panasonic alarm protocol]
Select “On”  or “Off”  to determine whether or not to provide notification by Panasonic alarm protocol according
to the settings for the “Alarm” and “Diag.” checkboxes of “Destination of notification” below.
– When an alarm is detected (“Alarm”)
– When a notification of the remaining capacity of the SD memory card has been provided (“Diag.”)
– When the SD memory card has...