Panasonic Network Camera Wv Sfv481 Operating Instructions

Note•When  “On” is selected, notification of the alarm occurrence will be provided to the registered destination
server addresses in order (to IP address 1 first, to IP address 8 last).
[Additional alarm data]
Determine whether or not to send notifications for VMD alarm detection area numbers with the Panasonic
alarm protocol by selecting On/Off.
• Default:  Off
[Destination port]
Select a destination port for the Panasonic alarm protocol from the following.
• Available range:  1 - 65535
• Default:...

IMPORTANT•When entering the host name of the “Destination server address”, the DNS settings on the [Network]
tab of the “Network” page must be configured. ( ®page 159)
• Confirm that the destination IP addresses are registered correctly. When a registered destination does
not exist, notification may be delayed.
13.6.2  Configure the settings relating to HTTP alarm notification
HTTP alarm notification [Address 1] - [Address 5]
Enter the destination IP address or host name of the HTTP alarm notification....

•Unavailable characters:  " & : ; \
[Password]
Enter the password to access the HTTP server.
• Available number of characters:  0 - 63 characters
• Unavailable characters:  " &
[Notification data]
Enter the notification data to add after the destination HTTP server addresses set in [Address 1] - [Address
5].
• Available characters:  Alphanumeric characters
• Default:  /cgi-bin/comalarm.cgi?CMD=01
Note
•For “Address 1” to “Address 5”, a total of 256 characters can be entered for the address...

14   Configure the settings relating to the
authentication [User mng.]
The settings relating to the authentication such as users and PCs restrictions for accessing the camera with a
PC or cellular phone/mobile terminal can be configured on the “User mng.” page.
The “User mng.” page has 3 tabs; the [User auth.] tab, the [Host auth.] tab and the [System] tab.
14.1  Configure the settings relating to the user
authentication [User auth.] Click the [User auth.] tab on the “User mng.” page. ( ®page 56, page...

Note•When the [Authentication] setting has been changed, close the web browser, and then access the
camera again.
• For other devices such as network disk recorders, unless otherwise stated, Digest authentication is
not supported. (As of October, 2014)
[User name]
Enter a user name.
• Available number of characters:  1 - 32 characters
• Unavailable characters:  " & : ; \
• Default:  None (blank)
[Password] [Retype password]
Enter a password.
• Available number of characters:  4 - 32 characters
•...

The restriction settings of PCs (IP address) from accessing the camera can be configured on this page.
[Host auth.]
Select “On” or “Off” to determine whether or not to authenticate the host.
• Default:  Off
[IP address]
Enter the IP address of the PC to be allowed to access the camera. Host name cannot be entered for the IP
address.
Note
•When “IP address/subnet mask”  is entered, it is possible to restrict PCs in each subnet. For example,
when “192.168.0.1/24” is entered and “2. Camera control” is...

Note•When “Quad stream” is selected for “Image capture mode”, system settings are not available.
Priority stream
[Activation]
Select “On” or “Off” to determine whether or not to use the priority stream.
• Default:  Off
Note
•When  “On” is selected for  “Activation” of “Priority stream ”, number of users who can access the camera
may be limited.
[Destination IP address(1)]
Enter the first destination IP address.
[Destination IP address(2)]
Enter the second destination IP address.
[Stream type]
Select...

Note•When “On” is selected for “H.264 transmission”, the transmission interval may be longer than the set
value when any value with an asterisk (*) on the right is selected.158Operating Instructions
14 Configure the settings relating to the authentication [User mng.] 

15   Configuring the network settings [Network]The network settings can be configured on the “Network” page.
The “Network” page has the [Network] tab and the [Advanced] tab.
15.1  Configure the network settings [Network] Click the [Network] tab on the “Network” page. ( ®page 56, page 58)
The following information is required to configure the network settings. Contact the network administrator or
your Internet service provider.
• IP address
• Subnet mask
• Default gateway (when using the gateway...

IPv4 network[Network Settings]
Select the method of how to configure the IP address from the following.
• Static:  The IP address is configured by entering manually on “IP address(IPv4)”.
• DHCP:  The IP address is configured using the DHCP function.
• Auto(AutoIP):  The IP address is configured using the DHCP function. When the DHCP server is not found,
the IP address is automatically configured.
• Auto(Advanced):  Using the DHCP function, network address information is referred to, and an unused
IP...