Panasonic Network Camera Wv Sfv481 Operating Instructions

							13.4.3  Configure settings relating to recording to an SD memory
card when an alarm occurs
Click “ SD memory card  >>” of “Camera action on alarm ” on the [ Alarm] tab of the  “Alarm” page. ( ®page 137)
Refer to page 70 for information on configuration for these settings.
Operating Instructions141
13 Configure the alarm settings [Alarm]   
						

							13.4.4  Configure settings relating to Panasonic alarm protocol
notification when an alarm occurs Click “Panasonic alarm protocol notification >>” of “Camera action on alarm” on the [Alarm] tab of the
“Alarm” page. ( ®page 137)
Refer to page 150 for information on configuration for these settings.
142Operating Instructions
13 Configure the alarm settings [Alarm]   
						

							13.4.5  Configure settings relating to HTTP alarm notification when
an alarm occurs Click “HTTP alarm notification >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page.
( ® page 137)
Refer to page 152 for information on configuration for these settings.
13.4.6  Configure settings relating to camera actions on alarm
action Click “Preset action on alarm >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page.
( ® page 137)
IMPORTANT
•Preset action upon alarm detection can be configured when “Quad PTZ”, “Single PTZ”, “8M Fisheye
+ Quad PTZ”, “4M Fisheye + Quad PTZ”, or “Quad stream” is selected for “Image capture mode”.
[Terminal alarm 1]
Operating Instructions143
13 Configure the alarm settings [Alarm]     
						

							Select an action to be taken when a terminal alarm 1 is detected from the following.
• Off:  Does not take any action even when a terminal alarm 1 is detected.
• (Quad PTZ) [1-4]/[5-8]/[9-12]/[13-16]:  When using Quad PTZ, all of the 4 screens move to their preset
positions.
• (Single PTZ) 1-16:  If a previously registered preset position is selected, when a terminal alarm 1 is
detected, the camera will move to that position.
• Default:  Off
[Terminal alarm 2]
Select an action to be taken when a terminal alarm 2 is detected from the following.
• Off:  Does not take any action even when a terminal alarm 2 is detected.
• (Quad PTZ) [1-4]/[5-8]/[9-12]/[13-16]:  When using Quad PTZ, all of the 4 screens move to their preset
positions.
• (Single PTZ) 1-16:  If a previously registered preset position is selected, when a terminal alarm 2 is
detected, the camera will move to that position.
• Default:  Off
[Terminal alarm 3]
Select an action to be taken when a terminal alarm 3 is detected from the following.
• Off:  Does not take any action even when a terminal alarm 3 is detected.
• (Quad PTZ) [1-4]/[5-8]/[9-12]/[13-16]:  When using Quad PTZ, all of the 4 screens move to their preset
positions.
• (Single PTZ) 1-16:  If a previously registered preset position is selected, when a terminal alarm 3 is
detected, the camera will move to that position.
• Default:  Off
[VMD alarm]
Select an action to be taken when a VMD alarm is detected from the following.
• Off:  Does not take any action even when a VMD alarm is detected.
• (Quad PTZ) [1-4]/[5-8]/[9-12]/[13-16]:  When using Quad PTZ, all of the 4 screens move to their preset
positions.
• (Single PTZ) 1-16:  If a previously registered preset position is selected, when a VMD alarm is detected,
the camera will move to that position.
• Default:  Off
[Command alarm]
Select an action to be taken when a command alarm is detected from the following.
• Off:  Does not take any action even when a command alarm is detected.
• (Quad PTZ) [1-4]/[5-8]/[9-12]/[13-16]:  When using Quad PTZ, all of the 4 screens move to their preset
positions.
• (Single PTZ) 1-16:  If a previously registered preset position is selected, when a command alarm is
detected, the camera will move to that position.
• Default:  Off
13.5  Configure the VMD settings [VMD area] Click the [VMD area] tab on the “Alarm” page. ( ®page 56, page 58)
The video motion detection areas can be set on this page.
Up to 4 areas can be set. When motion is detected in the set area, it will be regarded as an alarm.
IMPORTANT
•The alarm occurrence indication button ( ®page 19) will be displayed when motion is detected by the
VMD function.
• The alarm occurrence indication button will be displayed when receiving an alarm input of a terminal
alarm or a command alarm.
144Operating Instructions
13 Configure the alarm settings [Alarm] 
						

							•Depending on the network environment, notification may be delayed even when  “Real time ” is selected
for “Alarm status update mode” on the [Basic] tab of the “Basic” page ( ®page 62).
• After configuring the VMD area, the VMD area may move out of alignment when the JPEG/H.264
“ Image capture mode ” setting is changed. Make sure to check the VMD area after changing the  “Image
capture mode” setting.
• The motion detection function is not the dedicated function to prevent thefts, fires, etc. We are not
responsible for any accidents or damages that may occur.
[VMD image type]
When the “Image capture mode” type is “2 Monitor”, select the image that VMD detection will be performed
on.
Operating Instructions145
13 Configure the alarm settings [Alarm]    
						

							When “8M Fisheye + Panorama” or “4M Fisheye + Panorama” is selected for “Image capture mode”:
– Fisheye:  Performs video motion detection with Fisheye images.
– Panorama:  Performs video motion detection with Panorama images.
When “8M Fisheye + Double Panorama” or “4M Fisheye + Double Panorama” is selected for “Image
capture mode”:
– Fisheye:  Performs video motion detection with Fisheye images.
– Double panorama:  Performs video motion detection with Double Panorama images.
When “8M Fisheye + Quad PTZ” or “4M Fisheye + Quad PTZ” is selected for “Image capture mode”:
– Fisheye:  Performs video motion detection with Fisheye images.
– Quad PTZ:  Performs video motion detection with Quad PTZ images.
• Default:  Fisheye
IMPORTANT
•Changes to “VMD image type” are immediately applied.
• Areas are deleted when the  “VMD image type ” settings are changed. In this case, reconfigure the areas.
[Area]
When selecting a VMD area in the screen, it will be numbered as area 1.  (Subsequent areas will be numbered
in the order of selection.)
[All areas] button
When the [All areas] button is clicked, the whole area will become the VMD area, and “1(White)” will be
automatically applied to “Area”.
Note
•When Double Panorama is used, “1(White)” and “2(Blue)” are configured for “Area”.
• When Quad PTZ is used, “1(White)” to “4(Red)” are configured for “Area”.
[Status]
Select “On” or “Off” to determine whether or not to perform video motion detection.
• On:  Performs video motion detection.
• Off:  Does not perform video motion detection.
• Default:  Off
[Detection area]
Adjust the size of the VMD area using the slider. The smaller the selected value is, the higher the sensitivity
of VMD area becomes. The current value (1-10) will be displayed on the right of the slider.
• Default:  1
[Detection sensitivity]
Adjust the sensitivity of motion detection in the VMD area using the slider. The settings can be configured for
each area individually. The larger the value is set, the higher the sensitivity level becomes.
The current value (1 (low) - 15 (high)) will be displayed below the slider.
• Default:  8
[Delete] button
Click the [Delete] button corresponding to the area to be deleted. The outline of the selected area will be
deleted.
[Light detection control]
Select “On” or “Off” to determine whether or not to suspend video motion detection affected by brightness
change such by a dimming level control.
• Default:  Off
146Operating Instructions
13 Configure the alarm settings [Alarm] 
						

							IMPORTANT•“Light detection control” may not work when brightness change is too small.
• When “On” is selected for “Light detection control”, the video motion detection may not be performed
even when detecting a subject moving over the whole screen.
[Area No. notification]
When “Panasonic alarm protocol notification >>” is clicked, the [Notification] tab of the “Alarm” page will be
displayed. ( ®page 149)
VMD information addition [Information addition]
Select “On” or “Off” to determine whether or not to add VMD information to superimposed image data.
The VMD information can be searched by some of Panasonic network disk recorders. Refer to the operating
instructions of the connected devices for further information about the functions and settings.
• Default:  Off
13.5.1  Set the VMD areas [VMD area] Set the areas to activate the VMD function.
IMPORTANT•When the settings are being configured on the setup menu, sometimes the VMD function may not work
correctly.
Operating Instructions147
13 Configure the alarm settings [Alarm] 
						

							1.Set the video motion detection area by dragging the mouse on the screen.
→ The designated area will become the VMD area “1(White)” and the outline will be displayed. When 2
- 4 VMD areas are set, each area will be numbered in order. The areas will be identified by the
respective outline colors. The “Status” of the outline to be set for the area will become “On”.
Note
•When “Fisheye”, “Single PTZ”, or “Panorama” is selected for “Image capture mode”, 4 areas can
be configured.
• When “Double Panorama” is selected for “Image capture mode”, 2 areas can be configured for
each of the upper and lower images.
148Operating Instructions
13 Configure the alarm settings [Alarm]    
						

							•When  “Quad PTZ ” is selected for  “Image capture mode ”, 1 area can be configured for each image.
2. Adjust “Detection area” and “Detection sensitivity” using the slider.
Refer to page 144 for further information about the “Detection sensitivity” and “Detection area”.
The currently displayed area and its detection sensitivity will be displayed in the  “Detection area” section.
Change areas and the settings of “Detection area” and “Detection sensitivity” as necessary.
3. Click the [Set] button after completing the settings.
IMPORTANT
•The setting will not be applied unless the [Set] button is clicked.
4. To invalidate the VMD area, click the [Set] button after selecting “Off” for “Status” of the VMD area to be
invalidated.
→ The outline of the invalidated VMD area will turn to a dotted line. When the VMD area is invalidated,
no alarm will occur even when a motion can be recognized in the area.
5. To delete the VMD area, click the [Delete] button corresponding to the area to be deleted.
→ The outline of the respective VMD area will disappear.
6. Click the [Set] button.
→ The edited settings will be applied.
13.6  Configuration of the settings relating to alarm
notification [Notification] Click the [Notification] tab on the “Alarm” page. ( ®page 56, page 58)
The settings relating to Panasonic alarm protocol and HTTP alarm notification can be configured in this section.
Operating Instructions149
13 Configure the alarm settings [Alarm] 
						

							13.6.1  Configure the settings relating to Panasonic alarm protocol
Panasonic alarm protocol notification[Panasonic alarm protocol]
Select “On”  or “Off”  to determine whether or not to provide notification by Panasonic alarm protocol according
to the settings for the “Alarm” and “Diag.” checkboxes of “Destination of notification” below.
– When an alarm is detected (“Alarm”)
– When a notification of the remaining capacity of the SD memory card has been provided (“Diag.”)
– When the SD memory card has become full (“Diag.”)
– When the SD memory card cannot be recognized (“Diag.”)
• Default:  Off
150Operating Instructions
13 Configure the alarm settings [Alarm]