Panasonic Network Camera Wv Sfv481 Operating Instructions

[Dwell time] 
Select a wait time for switching between the color mode and the black & white mode from the following.
2s/ 10s/ 30s/ 1min
• Default:  10s
[White balance]
Select a method of white balance adjustment from the following.
White color can be adjusted by “Red gain” and “Blue gain”.
• ATW1:  Selects the automatic tracing white balance mode. The camera will constantly check the color
temperature of the light source and adjust the white balance automatically. Operating color temperature
range is...

Images will be sharper when the cursor is moved in the “+” direction, and will be softer when the cursor is
moved in the “-” direction. Click the [Reset] button to reset the color to the default.
• Default:  16
[Pedestal level]
Adjust the black level of images by moving the cursor.
When the cursor is moved to the “+” direction, images will become brighter. When the cursor is moved to the
“-” direction, images will be darker. Click the [Reset] button to reset the color to the default.
• Default:  128...

1.Display the “Image adjust” setup menu. ( ®page 106)Operating Instructions113
11 Configure the settings relating to images and audio [Image/Audio]   

2.Click the [Start] button of “Mask area”.
→ Borders will appear and the image displayed on the [Image quality] tab will be divided into 64 (8x8).
Note
•Regardless of the  “Image capture mode ” setting, Fisheye images are configured for mask settings.
114Operating Instructions
11 Configure the settings relating to images and audio [Image/Audio]    

3.Click the divided areas to be masked.
→ The clicked areas will be masked and will become white. To cancel masking, click the area again.
4.Click the [End] button after completing masking areas.
→ The borders on the image displayed on the [Image quality] tab will disappear.
IMPORTANT
•The mask area may move out of alignment if the setting for  “Image capture mode ” of the [JPEG/H.264]
tab or “Upside-down” of the [Basic] tab is changed after the mask area has been configured. Make
sure to check the...

IMPORTANT•This function is available when a  “Image capture mode ” setting containing  Quad PTZ or Single PTZ is
selected. ( ®page 9) Specifically, the following options can be selected for “Image capture mode”.
Quad PTZ/ Single PTZ/ 8M Fisheye + Quad PTZ/ 4M Fisheye + Quad PTZ/ Quad stream
Note
•“Preset position” can be set up to a maximum of 16 positions.
• When Quad PTZ, 8M Fisheye + Quad PTZ, 4M Fisheye + Quad PTZ, or Quad stream is selected for
“Image capture mode”, images are registered as Quad PTZ...

Register the preset positions1.Select a preset position number. When registering with Single PTZ, numbers 1 to 16 can be selected.
When registering with Quad PTZ, combinations of 1-4, 5-8, 9-12, or 13-16 can be selected.
→ The selected preset position number will be displayed in the “Position No” area.
When the selected number has already been registered, the camera will move to the selected preset
position.
2. Move the image position to the desired direction.
• The image position is changed with fisheye...

On this page you can adjust the 90° tilting angle and vertical angle set when the camera was mounted, as well
as the horizontal position of the cropping position.
When “Image capture mode” is set as follows, the initial position can be set.
Double Panorama/  Panorama/ 8M Fisheye + Double Panorama/ 4M Fisheye + Double Panorama/ 8M Fisheye
+ Panorama/ 4M Fisheye + Panorama
IMPORTANT
•VMD is deactivated while the initial position setup menu is displayed. Close the initial position setup
menu after...

•: Adjusts the display position upward.
•
:  Adjusts the display position downward.
[Set] button
Saves the adjusted screen position.
Note
•Up and down adjustments with the 
 and  buttons are based on panorama being in
its initial state. For example, if you use the 
 and  buttons after adjusting the display
position 90° to the left or right, the display will be adjusted to the left or right.
For Double Panorama images
[Position adjust] buttons
•
:  Images are displayed adjusted to 90° the left. The top...

11.6  Back focus setting (“Back focus” setup menu)Click the [Setup>>] button of “Back focus” on the [Image quality] tab of the “Image/Audio” page.
Adjust the back focus by moving the MOS image sensor of the camera to the appropriate position. Manual and
auto adjustment are available.
The back focus setting can be configured to automatically adjust the back focus and correct out of focus areas
when changing between color and black & white images.
[Auto back focus]
The auto back focus function starts to...