Panasonic Network Camera Wv Sfv481 Operating Instructions

Note•Refer to page 154 for further information about the access level.Operating Instructions131
11 Configure the settings relating to images and audio [Image/Audio] 

12   Configure the multi-screen settings
[Multi-screen]
The cameras from which images are to be displayed on a multi-screen can be registered on the
“Multi-screen” page. ( ®page 56, page 58)
[IP address]
Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be
registered as a group and up to 4 groups (16 cameras) can be registered.
When the HTTP port number for the camera of which images are to be displayed had been changed, enter as
follows:
Example of...

•“Network Camera Recorder with Viewer Software Lite” which supports live monitoring and recording
images from multiple cameras is available. For further information, refer to our website
(http://security.panasonic.com/pss/security/support/info.html).
• This camera is specified when “selfcamera” is displayed for the IP address or host name.
Note
•When using the host name, it is necessary to configure the DNS settings of the PC to be used for the
multi-screen display. Refer to the network administrator for...

13   Configure the alarm settings [Alarm]The settings for alarm actions, alarm images, VMD areas, and alarm occurrence notifications can be configured
on this page. The “Alarm” page has the [Alarm] tab, the [VMD area] tab, and the [Notification] tab.
13.1  Configure the settings relating to the alarm
action [Alarm] Click the [Alarm] tab on the “Alarm” page. ( ®page 56, page 58)
The settings relating to the alarm can be configured in this section. Refer to page  137 and page  136 for further
information...

[Terminal 3]
Determine how to use terminal 3.
• Off:  Not used.
• Alarm input:  Receives alarms. When “Alarm input” is selected, a pull-down menu for “Close” and
“Open” is displayed.
– Close:  An alarm is detected when the terminal status is changed to “Close”.
– Open:  An alarm is detected when the terminal status is changed to “Open”.
• AUX output:  AUX output will be supplied. The [AUX] buttons will be displayed on the “Live” page.
• Default:  Off
IMPORTANT
•In order for the EXT I/O terminals to...

13.2  Configure the settings relating to the alarm
output terminal [Alarm] Click the [Alarm] tab on the “Alarm” page. ( ®page 56, page 58)
The settings relating to the alarm output terminal can be configured in this section.
Alarm output terminal setup
[Alarm output trigger]
Select “On” or “Off”  to determine whether or not to output the alarm signals to the alarm output terminal when
an alarm is detected.
• Default:  Off
[Alarm output type]
Select “Latch” or “Pulse” for the alarm output terminal at an...

The names of “AUX”, “Open” and “Close” on the “Live” page can be changed.
AUX title[AUX (Up to 10 characters)]
Enter the name for “AUX” on the “Live” page.
• Unavailable characters:  " &
• Default:  AUX
[Open (Up to 5 characters)]
Enter the name for “Open” of “AUX” on the “Live” page.
• Unavailable characters:  " &
• Default:  Open
[Close (Up to 5 characters)]
Enter the name for “Close” of “AUX” on the “Live” page.
• Unavailable characters:  " &
• Default:  Close
Note
•AUX is a camera...

Click “FTP  >>” to display the setup menu that can configure the settings relating to FTP transmission when an
alarm occurs. The setup menu will be displayed in a newly opened window. ( ®page 139)
[Alarm image recording(SD memory card)]
Click “SD memory card >>” to display the setup menu that can configure the settings relating to recording
images on an SD memory card when an alarm occurs. The setup menu will be displayed in a newly opened
window. ( ®page 141)
[Panasonic alarm protocol]
Click “Panasonic...

•When “On(NTSC)” or “On(PAL)” is selected for “Monitor out”, images cannot be attached to E-mail
notifications.
Refer to page 164 for information on configuration for these settings.
13.4.2  Configure settings relating to FTP transmissions of alarm
images
Click “FTP >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page. ( ®page 137)
IMPORTANT
•When “Quad stream”  is selected for “Image capture mode ”, alarm images cannot be transmitted to an
FTP server.
Operating Instructions139
13...

•When “On(NTSC)” or “On(PAL)” is selected for “Monitor out”, alarm images cannot be sent to FTP
servers.
Refer to page 166 for information on configuration for these settings.
140Operating Instructions
13 Configure the alarm settings [Alarm]