Panasonic Network Camera Wv Sfv481 Operating Instructions

11.7  Configure the settings relating to the privacy
zone (“Privacy zone” setup menu) Click the [Setup>>] button of “Privacy zone” on the [Image quality] tab of the “Image/Audio” page.
( ® page 106)
When there is a zone that you do not want to display, set the zone as a privacy zone not to be displayed. Up
to 8 privacy zones can be set.
Note
•Regardless of the “Image capture mode” setting, Fisheye images are configured for privacy zone.
[Area]
The privacy zone will be set when an area is designated by...

[Status]
Select “On” or “Off” to determine whether or not to display the privacy zone.
• On:  The privacy zone will be displayed.
• Off:  The privacy zone will not be displayed.
• Default:  Off
[Delete] button
Click the [Delete] button corresponding to the zone to be deleted.
[Close] button
Click this button to close the “Privacy zone” setup menu.
IMPORTANT
•The privacy zone may move out of alignment if the settings for  “Image capture mode ” of the [ JPEG/H.
264 ] tab or  “Upside-down”  of the [Basic]...

11.8  Configure the VIQS settingClick the [Setup>>] button of “VIQS” on the [Image quality] tab of the “Image/Audio” page. ( ®page 106)
VIQS is an abbreviation of Variable Image Quality on Specified area and is a feature that enables you to change
the images of a specified area.
It is possible to enhance the image quality of the specified range within a shooting area (image).
It is also possible to moderate the image data size by lowering the image quality of other areas.
The VIQS setting is available...

Note•The VIQS setting is only available when “9M Fisheye” or “4M Fisheye” is selected for “Image capture
mode”.
[Area]
When selecting a VIQS area in the screen, it will be numbered as area 1.  (Subsequent areas will be numbered
in the order of selection.)
[Status]
Select “On” or “Off” to determine whether or not to use the VIQS area.
• On:  The VIQS area will be set.
124Operating Instructions
11 Configure the settings relating to images and audio [Image/Audio]    

•Off:  Does not set the VIQS area.
• Default:  Off
[Delete] button
Deletes the VIQS area. Click the button to delete the VIQS area.
[Level]
Configure the difference level in the image quality between specified areas and non-specified areas. The
greater the difference level, the more the image quality of the non-specified area is reduced. This makes it
possible to moderate the image data size.
0 Min./ 1/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Max.
• Default:  5 Normal
Stream [H.264(1)]
Select “On” or “Off” to...

11.9  Configure the VIQS areaThe VIQS area is specified by following the steps below.
1. Drag the mouse on the screen to specify the area (up to 8 areas).
→ The specified area is set to area “1(White)”, and the outline is displayed.
The areas are set in the area number order from number 1. The color next to the area number show
the color of the corresponding outline.
2. Configure the difference level in the image quality between specified areas and non-specified areas. The
greater the difference level,...

4.Click the [Set] button.
→ This unit is updated with the setting contents. Click the [ Delete] button corresponding to the area to be
deleted.
5. Click the [Confirm] button.
→ The image (“H.264(1)” or “H.264(2)”) that the [Confirm] button was pressed for is displayed. When a
window is newly opened and about 3 seconds pass, the currently outputted bit rate can be confirmed
with the configured VIQS.
IMPORTANT
•No setting contents are determined unless the [Set] button is clicked.
• To check the image...

11.10  Configure the settings relating to audio
[Audio] Click the [Audio] tab on the “Image/Audio” page. ( ®page 56, page 58)
The settings relating to audio can be configured on this page.
Note
•Images and audio will not be synchronized. Therefore, images and audio may not always match.
• Audio may be interrupted depending on the network environment.
[Audio transmission/reception]
Select the communication mode used for audio data transmission/reception between the camera and the PC
from the following.
•...

[Mic select] 
“Mic select” can only be configured when  “Mic input”, “Interactive(Half-duplex)” , or “Interactive(Full-duplex)” is
selected for “Audio transmission/reception”.
• Internal:  The camera’s built-in mic is used.
• External:  Uses the audio inputted from the mic or the line input terminal. An audio cable  (accessory) must
be connected to the audio cable connector.
• Default:  Internal
[Audio encoding format]
Select the audio reception encoding format from G.726, G.711, and AAC-LC.
• Default:...

•Default:  40ms
Note
•When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected,
audio interruption may be diminished even though the delay time will be longer. Select the interval
according to the network environment.
• “Mic input interval (Camera to PC)” is unavailable when “AAC-LC” is selected for “Audio encoding
format”.
[Audio output volume (PC to Camera)]
Select a volume level on the camera to hear audio transmitted from the PC.
High/ Middle/ Low
•...