Panasonic Kx Ta308 User Manual

							Station Programming (Personal Programming)2-3
2.1 Station Programming Instructions
To confirm the assigned data
—Be sure that you are in the Station Programming mode. Press the PROGRAM button.
PT
Press HOLD. Enter the program access number.
program access numberHOLD
— To exit the Station Programming mode, press the PROGRAM button.
— If you wish to change the data, follow the programming procedure explained in this
section.
* A program access numberis required to program/confirm the data by Station Programming.
• Enter the program access number*as follows.
- 1: Preferred Line Assignment — Outgoing
- 2: Preferred Line Assignment — Incoming
- 3: Outside (CO) Line Ringing Selection
- 4: Intercom Alert Assignment
- 5: Call Waiting Tone Type Assignment
- 6: Self-Extension Number Confirmation (KX-TA30830 only)
- 7: Extension Password Set (Manager only)
- 8: Electronic Station Lockout — CANCEL ALL
- 0: Date and Time Setting (Operator/Manager only)
- 
# : Station Programming Data Default Set
• The display shows the programmed data.

When you press “5”, the display shows:
— The Call Waiting tone is currently programmed to Tone 1.
C.W.Tone-1
• The display shows the initial programming mode. 
						

							2-4Station Programming (Personal Programming)
2.1 Station Programming Instructions
To confirm the assigned data on the Flexible button
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
— To exit the Station Programming mode, press the PROGRAM button.
— The following outline contains the buttons and program access numbers used for Station
Programming. Detailed operating instructions are explained in this section.— To exit the Station Programming mode, press the PROGRAM button.
— If you wish to change the data, follow the programming procedure explained in this
section.
To clear the data on the Flexible button
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
PT
Press HOLD. Press the desired Flexible button.
HOLD
• The display shows the initial programming mode.• The display shows the current status.
PT
Press the desired 
Flexible button that 
you wish to clear.Dial 2.Press STORE.
AUTO DIAL
STORE
• The STORE indicator lights.
• The display shows the initial programming mode. 
						

							(Preferred Line Assignment — Outgoing)
(Preferred Line Assignment — Incoming)
(Outside (CO) Line Ringing Selection)
(Intercom Alert Assignment)
(Call Waiting Tone Type Assignment)
(Self-Extension Number Confirmation)
(Extension Password Set)*
(Electronic Station Lockout — CANCEL ALL)*
(Date and Time Setting)*
(Station Programming Data Default Set)
(Exit) Direct Station Selection (DSS) Button
Conference (CONF) Button
FWD/DND Button
SAVE Button
Caller ID Indication — Personal Button
Caller ID Selection — Personal Button
Log-In/Log-Out Button
Another Extension Message Waiting Button
Caller ID Indication — Common Button
Caller ID Selection — Common Button
Single-CO (S-CO) Button
Other-CO (O-CO) Button
Group-CO (G-CO) Button
Station Programming (Personal Programming)2-5
2.1 Station Programming Instructions
Station Programming Outline
(Station Programming)
CO
MESSAGE
MESSAGE3
2
1
3
4
5
6
7
8
96
97
0
#
1
2
3
4
5
6
7
8
0
#
* See the “Operator/Manager
Service Features”
(Section 3.3).
CO
Return to MESSAGE Button
95
PROGRAM
PROGRAM
One-Touch Dialing Button 
						

							Call Waiting Tone Type Assignment
Allows you to select the call waiting tone type (Tone 1 or Tone 2).
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
— To exit the Station Programming mode, press the PROGRAM button.
Conditions
• The tone type patterns are described in the Appendix (Section 4).
• The default is “Tone 1”.
Feature References
Busy Station Signaling (BSS)
Call Waiting
PT
Dial 5.Press STORE.
or
Dial 1 or 2.
1 : to select Call Waiting Tone 1
2 : to select Call Waiting Tone 2
AUTO DIAL
STORE
125
•The STORE indicator lights.
•The display shows the initial programming mode.
•The display shows the current tone type.
2-6Station Programming (Personal Programming)
2.2 Station Programming (Personal Programming) 
						

							Station Programming (Personal Programming)2-7
2.2 Station Programming (Personal Programming)
Flexible Button Assignment
Each Flexible button on your telephone and the console can be assigned as various
feature buttons such as a DSS Button, FWD/DND Button, etc. The assignable features
are limited by the button type. Please refer to “Flexible Buttons” in Section 1.1.
Another Extension Message Waiting Button (Assignment)
Allows you to assign a Flexible CO button as an Another Extension Message Waiting
button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM
button.
— To exit the Station Programming mode, press the PROGRAM button.
Feature Reference
Message Waiting for Another Extension
PT
Press the desired Flexible CO button 
you wish to assign as an Another 
Extension Message Waiting button.Press STORE. Enter the extension number 
(100 through 199).
extension no.
Dial 95.
59COAUTO DIAL
STORE
•The STORE indicator
lights.
•The display shows the
initial programming mode.
MW–

extension number
•To erase an incorrect entry, press the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button during programming.)
MW–xxx 
						

							2-8Station Programming (Personal Programming)
2.2 Station Programming (Personal Programming)
Caller ID Indication Button (Assignment)
Allows you to assign a Flexible CO button as the Caller ID Indication button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
PT
Press the desired Flexible CO button you wish to 
assign as the Caller ID Indication — Personal button.Dial 6.Press STORE.
–– Personal
Press the desired Flexible CO button you wish to 
assign as the Caller ID Indication — Common button.Press STORE.
–– Common
Dial 96.
6
69
CO
CO
AUTO DIAL
STORE
AUTO DIAL
STORE
•The STORE indicator lights.
•The display shows the initial programming mode.
— To exit the Station Programming mode, press the PROGRAM button.
Condition
•System Programming determines who can assign the Caller ID Indication — Common
button.
Programming Reference
•System Programming — Installation Manual
[909] Common Area Call Log Check Assignment
Feature References
Call Information/Log, Incoming
Call Log, Incoming PT

CID-P Indication
•The STORE indicator lights.
•The display shows the initial programming mode.

CID-C Indication 
						

							Station Programming (Personal Programming)2-9
2.2 Station Programming (Personal Programming)
Caller ID Selection Button (Assignment)
Allows you to assign a Flexible CO button as the Caller ID Selection button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
— To exit the Station Programming mode, press the PROGRAM button.
Condition
•System Programming determines who can assign the Caller ID Selection — Common
button.
Programming Reference
•System Programming — Installation Manual
[909] Common Area Call Log Check Assignment
Feature References
Call Information/Log, Incoming
Call Log, Incoming PT
PT
Press the desired Flexible CO button you wish to 
assign as the Caller ID Selection — Personal button.Dial 7.Press STORE.
–– Personal
Press the desired Flexible CO button you wish to 
assign as the Caller ID Selection — Common button.Press STORE.
–– Common
Dial 97.
7
79
CO
CO
AUTO DIAL
STORE
AUTO DIAL
STORE
•The STORE indicator lights.
•The display shows the initial programming mode.

CID-P Selection
•The STORE indicator lights.
•The display shows the initial programming mode.

CID-C Selection 
						

							2-10Station Programming (Personal Programming)
2.2 Station Programming (Personal Programming)
— To exit the Station Programming mode, press the PROGRAM button.
Feature References
Conference
Conference, Unattended
PT
Press the desired Flexible CO 
button you wish to assign as 
the Conference button.Dial 3.Press STORE.
3COAUTO DIAL
STORE

Conference
•The STORE indicator lights.
•The display shows the initial programming mode.
Conference (CONF) Button (Assignment)
Allows you to assign a Flexible CO button as the Conference (CONF) button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM button. 
						

							Direct Station Selection (DSS) Button (Assignment)
Allows you to assign a Flexible CO button as a DSS button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
Station Programming (Personal Programming)2-11
2.2 Station Programming (Personal Programming)
— To exit the Station Programming mode, press the PROGRAM button.
Feature Reference
Intercom Calling
PT
Press the desired Flexible CO
button you wish to assign as 
a DSS button.Dial 1.
Press STORE. Enter the extension number 
(100 through 199).
extension no.
AUTO DIAL
STORE
1CO
•The STORE indicator lights.
•The display shows the initial
programming mode.
EXT–

extension number
•To erase an incorrect entry, press the TRANSFER (CLEAR)
button.
(The TRANSFER button becomes the CLEAR button during
programming.)
EXT–xxx 
						

							2-12Station Programming (Personal Programming)
2.2 Station Programming (Personal Programming)
FWD/DND Button (Assignment)
Allows you to assign a Flexible CO button as the FWD/DND button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
PT
Press the desired Flexible CO 
button you wish to assign as 
the FWD/DND button.Dial 4.Press STORE.
4COAUTO DIAL
STORE
•The STORE indicator lights.
•The display shows the initial programming
mode.
FWD/DND
— To exit the Station Programming mode, press the PROGRAM button.
Feature References
Call Forwarding
Do Not Disturb (DND)
Group-CO (G-CO) Button (Assignment)
Allows you to assign a Flexible CO button as a Group-CO button.
— Be sure that you are in the Station Programming mode. Press the PROGRAM button.
PT
Press the desired Flexible 
CO button you wish to 
assign as a G-CO button.Dial #.Press STORE. Enter the outside (CO) line group 
(trunk group) number (1 through 3).
outside (CO) line group no.COAUTO DIAL
STORE
•The STORE indicator lights.
•The display shows the initial
programming mode.

outside (CO) line group number
•To erase an incorrect entry, press the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button during programming.)
TRG GRP–x

TRG GRP–
— To exit the Station Programming mode, press the PROGRAM button.