Panasonic Kx Ta308 User Manual

							Telephone Features3-97
3.2 Telephone FeaturesP
Paging — DENY
A page sent to a built-in speaker can be denied by any extension in the system.
Setting
PT
Dial 7341#.Lift the handset or press 
SP-PHONE/MONITOR.Hang up or press 
SP-PHONE/MONITOR.
1437

Paging Deny
PT
Dial 7340#.Lift the handset or press 
SP-PHONE/MONITOR.Hang up or press 
SP-PHONE/MONITOR.
0437

Paging Allow
Canceling 
						

							3-98Telephone Features
P3.2 Telephone Features
Paralleled Telephone Connection
Any extension can be connected in parallel with a proprietary telephone and a single line
telephone. In the event of a power failure, CO1 can be accessed using the single line
telephone that is connected in parallel with the proprietary telephone to jack number 01.
If the extension receives a call, ringing will be heard from the proprietary telephone and
the single line telephone. You can answer the call by using either the proprietary
telephone or the single line telephone. An answering machine, facsimile, MODEM
(personal computer), etc., can be connected instead of a single line telephone.
System Programming is required to enable this feature.
Conditions
•A proprietary telephone LCD will show you a single line telephone is in use.
•The following features will not work with a single line telephone connected in parallel
with a proprietary telephone.
Call Splitting
Caller ID Call Waiting
Conference
Door Opener while talking to the doorphone
External Feature Access
Pickup dialing
•A single line telephone connected in parallel with a proprietary telephone cannot make
a call in the following cases.
— The proprietary telephone is set to the BGM mode.
— The proprietary telephone is receiving a page through the built-in speaker.
— The proprietary telephone is set to the PROGRAM mode.
•A single line telephone connected in parallel with a proprietary telephone will not ring
in the following cases.
— The proprietary telephone is set to Hands-free Answerback.
— The proprietary telephone is set to “Voice Call” in the Intercom Alert Assignment.
— The proprietary telephone is receiving a call from a doorphone.
Programming Reference
•System Programming — Installation Manual
[610] Paralleled Telephone Connection SLT
SLT
SLT
PT 
						

							Telephone Features3-99
3.2 Telephone FeaturesP
Personal Speed Dialing
Allows you to store up to ten speed dial numbers at your extension. These numbers are
available for your extension only.
Storing a phone number
Any Telephone
Confirmation 
tone Lift the handset 
or press 
SP-PHONE/
MONITOR.
Dial 2   .Enter the personal speed 
dial number (0 through 9).
personal speed dial no.
Enter the 
desired number.
desired no.
Dial #.Hang up or press SP-PHONE/MONITOR.
2
Any Telephone
Lift the handset or press 
SP-PHONE/MONITOR.Dial #.
Enter the personal speed 
dial number (0 through 9).
personal speed dial no.
•You may dial “1” instead of “#”.
Dialing
PT
Lift the handset or press SP-PHONE.Dial 3   .Enter the personal speed 
dial number (0 through 9).
personal speed dial no.
Dial #.
3
Checking the stored personal speed dialing numbers (with a display PT only) 
						

							3-100Telephone Features
P3.2 Telephone Features
Conditions
•An account code must be stored by pressing “” and entering the account code after
the line access code in the account code verify-all and forced modes.
•You can store an extension number, telephone number, or feature number of up to
twenty-four digits. Valid digits are “0 through 9”.
•A pause can be stored by pressing the  key. However, in the account code verify-all,
verify-toll and forced modes, “” is not regarded as a pause.
•To store the telephone number of an external party, a line access code (9 or 81 through
83) must be stored as the first digit.
•A rotary telephone cannot use this feature.
Programming Reference
•Station Programming (Section 2)
Flexible Button Assignment — One-Touch Dialing Button SLT 
						

							Telephone Features3-101
3.2 Telephone FeaturesP
Conditions
•This feature will not work if you answer an incoming call or retrieve a call on hold.
•Up to thirty-two digits, consisting of “0 through 9” and “”, can be stored. The “”
button is used as a PAUSE. However, in the account code verify-all, verify-toll and
forced modes, “” is not regarded as a pause.
•An account code must be stored by pressing “” and entering the account code after
the line access code in the account code verify-all and forced modes.
•During the waiting time after going off-hook, you can call another party and override
this feature. You can change the waiting time between going off-hook and connecting
with a called line by System Programming.
•A rotary telephone cannot use this feature.
Programming Reference
•System Programming — Installation Manual
[203] Pickup Dial Delay Time
Pickup Dialing (Hot Line) (— Single Line Telephone only)
Allows you to make an outgoing call by just going off-hook.
Storing a phone number
SLT
Confirmation 
tone and 
dial tone Lift the handset 
or press 
SP-PHONE/
MONITOR.Dial 742.
Enter the phone number.
phone no.
Dial #.Hang up or press SP-PHONE/MONITOR.
427
•You must dial a line access code (9 or 81 through 83) as the first
digit when storing an external party phone number.
SLT
Confirmation tone 
and dial tone Lift the handset or press 
SP-PHONE/MONITOR.Hang up or press 
SP-PHONE/MONITOR. To set: Dial 741#.
To cancel: Dial 740#.
To set.
To cancel.147
047
Setting / Canceling
SLT
Lift the handset or press 
SP-PHONE/MONITOR.Wait for an answer.Talk.
Dialing 
						

							3-102Telephone Features
P3.2 Telephone Features
Power Failure Transfer
During a power failure, the following outside (CO) line will be connected to an assigned
extension.
Outside (CO) line 1: jack number 01
Conditions
•During a power failure, all features cannot be used except for incoming and outgoing
outside calls from jack number 01.
•If jack number 01 is connected to a proprietary telephone, disconnect the unit and
connect a single line telephone. 
						

							Telephone Features3-103
3.2 Telephone FeaturesP
Condition
•You cannot change from Tone to Pulse dialing mode.
Pulse to Tone Conversion 
Allows you to change the dialing mode from Pulse to Tone to access services that require
tones, such as computer telephone services.
Any Telephone
Dial    #.Enter the phone number 
(Pulse mode).
phone no. (Pulse mode)desired no. (Tone mode)
Enter the desired number 
(Tone mode). 
						

							3-104Telephone Features
R3.2 Telephone Features
Conditions
•Up to sixty-four digits can be stored and redialed. This does not include an outside
(CO) line access code.
•If you hear a busy tone when attempting to redial, select another line and press the
REDIAL button or feature number.
•The stored number will be replaced even if only one digit is dialed the next time an
outside call is made. Dialing an outside (CO) line access code will not affect the stored
number.
•“ ”, “#”, “PAUSE”, and “INTERCOM” (for secret dialing) are counted as one digit.
•While calling or during a conversation, pressing the REDIAL button will disconnect
the current call and redial the stored number in 3 seconds.
•You can check the stored number. Press the REDIAL button while on-hook, and the
stored number will be displayed. PT
PT
PT
Redial, Last Number
Automatically saves the last outside phone number dialed so that you can make a call to
the same party later using a simple operation.
PTSLT
Lift the handset. Dial ## or 80.Press REDIAL.Lift the handset or press 
SP-PHONE/MONITOR.
08orREDIAL 
						

							Telephone Features3-105
3.2 Telephone FeaturesR
Conditions
• Up to sixty-four digits can be stored and redialed. This does not include an outside(CO) line access code.
• “ ”, “#”, “PAUSE”, and “INTERCOM” (for secret dialing) are counted as one\
 digit.
• A flexible button can be assigned as the SAVE button.
• You can check the stored number. Press the pre-assigned SAVE button while on-hook, and the stored number will be displayed.
• You can change the outside (CO) line when dialing. You may press a CO button to select an outside (CO) line directly after going off-hook before pressing the 
pre-assigned SAVE button.
Programming Reference
• Station Programming (Section 2) Flexible Button Assignment — SAVE Button
PT
PT
PT
PT
PT
Redial, Saved Number
Allows you to save the current external telephone number during a conver\
sation, so that
you can redial the same party later using a simple operation. The saved number can be
redialed until another number is stored.
Storing
PT
Press the Flexible CO button 
assigned as the SAVE button.
Press AUTO DIAL/STORE.
During a conversation or while hearing a busy tone
AUTO DIAL
STORE
PT
Press the Flexible CO button 
assigned as the SAVE button.Lift the handset or press 
SP-PHONE/MONITOR.
Dialing 
						

							3-106Telephone Features
R3.2 Telephone Features
Room Monitor
Allows you to monitor a room through a proprietary telephone with an
AUTO ANSWER/MUTE button. The proprietary telephone you want to monitor should
be prepared for monitoring beforehand. You can also monitor through a doorphone. You
can use a proprietary telephone with an AUTO ANSWER/MUTE button and single line
telephone with a MUTE button for monitoring.
Setting a monitored PT
PT
Lift the handset or 
press SP-PHONE.Press AUTO ANSWER/MUTE.Dial 7351#.
Confirmation toneHang up or press SP-PHONE.
At the monitored telephone
AUTO ANS
MUTE
1537

Room Monitor On•The AUTO ANSWER/MUTE
button indicator is flashing.
PT and SLT
For a PT:   Press SP-PHONE and AUTO ANSWER/MUTE.
For an SLT: Lift the handset and press the MUTE button.Enter the monitored extension 
number (100 through 199).
extension no.Room monitoring 
starts.For a PT
For an SLT
SP-PHONEAUTO ANS
MUTE
MUTE
PT
Press AUTO ANSWER/MUTE or lift the handset.
or
Talk.
AUTO ANS
MUTE
Monitoring
Talking with a person in the monitored room