Panasonic Kx-T123210 Installation Manual

							TELEPHONE COMPANY and FCC.REQUIREMENTS AND RESPONSIBILITIES
In compliance with the requirements of Part 68 of
the 
F.C.C.Rules and Regulations for connection of
terminal system (this device is classified as terminal
system ) to the telephone network and for your
convenience, the following information is
presented :
1. Notification to the Telephone CompanyCustomers, before connecting terminal equipment
to the telephone network, shall upon request of the
Telephone Company, inform the Telephone
Company of the particular line(s) to which such
connection is made, the F.C.C. registration number
and (see label on side of unit. ) ringer equivalence
number of the registered terminal equipment.
The REN is useful to determine the quantity of
devices you may connect to your telephone line and
still have all of those devices ring when your
telephone number is called. In most, but not all
areas, the sum of the 
REN’s of all devices connected
to one line should not exceed five (5.0 
). To be
certain of the number of devices you may connect
to your line, as determined by the REN, you should
contact your local telephone company to determine
rhe maximum REN for your calling area.
2. Direct connection to A Party-line or
Coin-operated Telephone Line is
Prohi bited
3. Incidence of Harm to The Telephone
linesShould Terminal Equipment cause harm to the
Telephone Network, the Telephone Company shall,
where practical, notify the customer that temporary
discontinuance of service may be required.
However, where prior notice is not practical, the
Telephone Company may temporarily discontinue
service forthwith, if such action is reasonable in the
circumstances. In case of such unnotified temporary
discontinuance of service, the Telephone Company
shall:
(a) Promptly notify the customer of such temporary
discontinuance of service.
(b) Afford the customer the opportunity to correct
the situation which gave rise to the temporary
discontinuance.
(c) Inform the customer of the right to bring a
complaint to the Commission pursuant to the
procedures set out in Subpart E of Part 68 of
FCC Telephone Equipment Rules.
4. Compatibility of The Telephone
Network and Terminal Equipment
(a) Availability of telephone interface
information.Technical information concerning interface
parameters and specifications not specified in
FCC Rules, including the number of Ringers
which may be connected to a particular
telephone line, which is needed to permit
Terminal Equipment to operate in a manner
compatible with Telephone Company
communications facilities, shall be provided by
the Telephone Company upon customer’s
request.
(b) Changes in Telephone Company
Communications Facilities, Equipment,
Operations and Procedures.The Telephone Company may make changes in
its communications facilities, equipment,
operations or procedures, where such action is
reasonably required in the operation of its
business and is not inconsistent with the rules
and regulations in FCC Part 68 of the FCC
Rules and Regulations. If such changes can be
reasonably expected to render any customer
Terminal Equipment incompatible with
Telephone Company Communications
Facilities,or require modification or alteration
of such Terminal Equipment, or otherwise
materially affect its use or performance, the
customer shall be given adequate notice in
writing, to allow the customer an opportunity
to maintain uninterrupted service.
6-8 
						

							OTHERS
l Keep the unit away from heating appliances and electrical noise generating devices
such as fluorescent lamps, motors and television. These noise sources can interfere
with the performance of the EASA-PHONE.
l This unit should be kept free of dust, moisture, high temperature and vibration, and
should not be exposed to direct sunlight.
l Never attempt to insert wires, pins, etc . into the vents or other holes of this unit
l If there is trouble, disconnect the unit from the telephone line. Plug the telephone
directly into the telephone line. If the telephone operates properly, do not reconnect
the unit to the line until the trouble has been repaired by an authorized Panasonic
Factory Service Center. If the telephone does not operate properly, chances are that
the trouble is in the telephone system, and not in the unit.
l Do not use benzine, thinner, or similar solvents. Do not use abrasive powder to clean
the cabinet. Wipe it with a soft cloth.
“WARNING-This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been tested and found to
comply with the limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the
user at his own expense will be required to take whatever measures may be
required to correct the interference.”
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 
						

							:.LIMITED WARRANTYPanasonic Company, PHI or PSC will repair this product with new or rebuilt parts, free of
charge, in the U.S.A. or Puerto Rico for one ( 1 ) year from the date of original purchase in the
event of a defect in materials or workmanship.
Batteries ( if included ) 
- New rechargeable batteries in exchange for defective rechargeable
batteries for ten (10) days from the date of original purchase. Non-rechargeable batteries are
not warranted.
Carry-in or mail-in service in the continental U.S.A. can be obtained during the warranty
period from a Matsushita Services Company (MSC ) Factory Servicenter listed in the Servicenter
Directory. Or call l-800-447-4700, toll free, to locate an authorized MSC Servicenter. Carry-in or
mail-in service in Puerto Rico or Hawaii can be obtained during the warranty period by calling
the telephone numbers listed in the Servicenter Directory (see page 6-11 ) .
This warranty is extended only to the original purchaser. A purchase receipt or other proof of
date of original purchase will be required before warranty performance is rendered.
This warranty only covers failures due to defects in materials or workmanship which occur
during normal use. It does not cover damage which occurs in shipment or failures which are
caused by products not supplied by Panasonic Company, PHI or PSC or failures which result
from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, modification, or service by anyone other than a MSC Factory Servicenter or
authorized MSC Servicenter or damage that is attributable to acts of God.
LIMITS AND EXCLUSIONSThere are no express warranties except as listed above.
PANASONIC COMPANY, PHI AND PSC SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE 
OFTHIS PRODUCT, OR ARISINGOUT OF ANY BREACH OF THIS WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some 
statesdo not allow the exclusion
or limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
If a problem with this product develops during the warranty period, you may contact your
dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the
Consumer Affairs Division at the company address indicated on the back cover.
6-10 
						

							SERVICENTER LISTTo locate an Authorized Servicenter in Your Area within the Continental U.S.A.
iwT5DIAL TOLL FREE : I-800-447-4700’
24 Hours a Day, 7 Days a WeekRequests for assistance in obtaining repairs or technical information...contact any one of the following Service
Administration offices:
EASTERNMIDWEST
WESTERN
SOUTHERN2250 Cabot Boulevard425 East Algonquin Road
6550 Katella Avenue
1854 Shackleford Court
West Lang horne, PA1 9047Arlington Heights, IL 60005Cypress, CA90630Norcross, GA30093
215-741-0676312-981-4842
714-895-7438
/-7,~-3,~-7’13g 404-g25-6860
/-74*373--74YO
Correspondence requesting product information should be sent to :Panasonic Consumer Affairs, Matsushita Services Company, Division of Matsushita Electric Corporation of
America, 50 Meadowland Parkway, Secaucus, NJ 07094
Service in Puerto Rico
MATSUSHITA ELECTRIC OF
PUERTO RICO, INC.
Panasonic Sales Company
Factory Servicenter
Calle Rosarito, Edif D
Ceramica Industrial Park
Carolina, Puerto Rico 00630
809-750-5135.809-750-5235Service in Hawaii
PANASONIC HAWAII, INC.
91-238 Kauhi Street, Ewa Beach
P.O. Box 774Honolulu, Hawaii 96808-0774
808-682-1521
Service in the Continental
U.S.A. . . . . FactoryServicenters1575 NORTHSIDE DRIVE SUITE 325
ATLANTA, GA 30318
(404)351-8978
MATSUSHITASERVICESCOMPANYDivision of Matsushita Electric Corporation of
America 50 Meadowland Parkway, Secaucus, New
Jersey 07094
6-11 
						

							Phone Number Directory
b TELEPHONE NUMBER 4,.coTEL NO. ,COTEL NO.coTEL NO.coTEL NO.
147102
5811
36
912
b EXTENSION NUMBER 4
b SPEED DIALING 4
CODENAMETEL NO.
0005
06 
						

							b SPEED DIALING 4
CODE 1NAMETEL NO.ICODENAME
TEL NO.
62
2563
2664
67
:i
36
37
77
41
42I 43 I1 
81 11 
82 1
II
83
84
85
86
87 47
48I 
49 I
II
50
511 
52 1
5391
5492I 
93 I
94
9597
98
6199 
						

							PROGRAMMING TABLE
TO SET ;“,;;;,“,”STEPS REQUIRED TO CHANGE PROGRAM
Date and Time
Settingm IN~~~~~~~~~~~~~~~
-.‘year:..,monthi-day ::.....,,,our:.- day of the weekL....-minute L.....-*M / PMSystem Speed
Dialing Entry
a/ ahone number 1 iMEMORY 1 mOR
mi,., 9 : automatic line access number
x8 q through q q :access number of Trunk Group
:......-Speed access code (00 through 99)
Q There is the phone number directory on page 7-l.
ExtensionVumber4ssignmentLil lNEXTl &~ORYlrn
:.....dial the extension number (100 through 199)
:..........until the desired jack number (01 through 32)appears
Dperator4ssignmentI
El =+~~FMoRyI lEJd. . . . ..dial the jack number set operator (01 through 32)
:....-until the desired operator number (1 or 2) appears
Jack number set operator
Operator 
1Operator 2Jack number set operator
‘aired
relephone4ssignment for
IGil riGaalaa]-ram~m
ISS Console:.,-dial the jack number paired with console 2 (01 through 32)
:...-, dial the jack number paired with console 1 (01 through 32)
Default
To make program changeJack number paired with Console 1
01Default
To make program changeJack number paired with Console 2
07
r\utomatic CO-told Using DSS3uttonIa mp5Ntzam.
With Transfer 
/ Without Transfer
DefaultTo make program change
With TransferX
Without Transfer
7-3
.: 
						

							TO SET ;E;;,“,”STEPS REQUIRED TO CHANGE PROGRAM
Day/Night
ServicelQsl LrnlSELECTllhnEMORYIModei.....Manual / Automatic
Switching of
-DefaultTo make program change
Service Mode
ManualXAutomatic
Starting Timem ~~~ICD~ISELECTIINIEMORYIIN~~~~lSELECTI~I
. . ..minute. ..- AM I PM;...minute.....’ AM I PM
L..... starting time for day service (hour)*.....-starting time for night service (hour)
To makeprogramchangeDay Service
9:00 AMNight Service
5:OO PM
Call Hunting
Setting
mlrJEXTl gd lyl lMF,bRYl IEEl. . . . . . . . . . .Disable / Enable
:....... until the desired extension group number (1 through 8)appears
DefaultTo make program change
all 8 extension.Extension group
groups
group 1 group 2 group 3 group 4 group5 group 6 group 7 group 8
DisableX
Enable
Hunting Type
Ilepl lNEXTlIiZiZl IMEMORY I lE&l
:......Terminate / Circular
I.......’ until the desired extension group number (1 through 8) appears
DefaultTo make program change
all 8 extensionExtension group
groups
group 1 group2 group3 group4 group5 group6 group7 group8
TerminateXCircular
Toll Restriction
m IialSELECTlllhnEMORYrnArea Type
I...... Type A/ Type B / Type CSelection
To makeprogram change
Type AX
.Type B
Type CCO Operator
Call-Boundary
liil lia@lNlEMoRVIClass
‘.........dial the boundary class number (1 through 8)
Class 1 Class 2 Class 3 Class 4 Class 5 Class 6 Class 7 Class 8
DefaultXTo make program change
,
::  
_...  .
7-4 
						

							TO SET ;$,;;“s”STEPS REQUIRED TO CHANGE PROGRAM
IToll Restriction{cent .)h lNEXTlEifaGmlENDl
TollRestriction.......Restriction / No restriction
of Speed Dialing
DefaultTo make program change
Restriction
XNo restriction
Exchange
Code Selection
IlCDEl IMEMORY I IEEl
:.....exchange code with 3 digits
.. .
until the desired memory code number
(01through20)appears
Memory code number
\ 01 1 02 1 03104 1051 06107108exchange code entry
IIIIMemory code number
09110 111 1 12 1 13 1 14 1 15I16 1171 18119120
IIIIIIIII
IArea Code Entry
for class 3
I&I IMEMORY I IEd
f....- area code with 3 digits
:.......... until the desired memory code number (01 through 20)appears
Memory code number
\ 01 1 02 1 03104 1051 06107108Area code entry
IIIIIIIMemory code number
09110 111 1 12 1 13 1 14 I 15I16 1171 18119120
IIIIIIIIIIExchange Code
Entry for Class 5
Ilijjd IMEMORY I EEI
-....- exchange code with 3 digits
:..........untilthedesiredmemorycodenumber(Ol through20)appearsMemory code number
01 1 02 1 03104 1
051 06107108exchange code entry
II
IIIIMemory code number
09110 111 1 12 1 13 1 14 I 15I16 I17I 18I19120
IIIIIIIII
t
,.:. . .  .  .;..
						

							TO SET ;“,;;gs”STEPS REQUIRED TO CHANGE PROGRAM
Toll Restriction
(cant)Exchange Code
Entry for Class 7Il&j I~~IEMORYI lENDl
:.....exchange code with 3 digits
. .
until the desired memory number (01 through 20) appears
Memory code number
01 1 02 1 03 1 04 1 05 1 06 1 07 1 08
Exchange code entry
I1II
IIIMemory code number
09 1 10 1 11 1 12 1 13 1 14 1 15 
[ 16 1 17 1 18 I 19 1 20
IIIIIIIIII
Hold TimeReminder11 INEXTIylhllEMORYm
..........dial the time (1 minute through 9 minutes)
minutes
1 2 3 4 5 6 7 8 9
DefaultXTo make program change
Hold Recall
Time SetIIliiE!lISELECTImlEPlD
‘““‘30 set / 1 min / 1.5 min / 2 min! Disable
DefaultTo make program change30seconds 1 minute
1 minute30 seconds 2 minutesdisable
XTransfer Recall
Time11 MliEyllNiEMORYllENOl
........ 30 set I 15 set30 
set
15 setTo make program change
Call Forwarding
Starting TimeizilhEi7ylNlEMORYI
........‘..I ring delay / 2 rings delay/ 3 rings delay / 4 rings delay
1 ring delay2 rings delay
3 rings delay
4 rings delay
Default
XTo make program change
Pickup Dial
Delay Time1211liii%yllWERnORYI
........,..l set I 2 set I3 set I 4 set
1 set
2 set
3 set4 
set
Default
XTo make program change