Panasonic Kx-T123210 Installation Manual

							,...................................... 
until the desired CO number (01 through 12) appears 
_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . until the desired jack number appears 
m : on jack number 01 
& : on jack number 32 
I# : to assign the same on all 32 jacks 
until the desired mode appears 
..e.......default (all 32 jack numbers) 
or 
f-$E--$ other $ number 
CD=l : to assign the same on all 32 jack numbers 
I: on jack number 01 
III 32 : on jack number 32 
AB=m : to assign the same on all 12 CO’s 
lol_l: on CO 01 C.............................................................. 
h 12 :onCO12 
Description 
Through programming, you can select which 
extensions will ring on incoming calls from the 
Central Office during the day time. 
Programming 
Dial (47). 
“Day In CO ” will be displayed. 
Press the NEXT button. 1. 
2. 
3. 
4. “CO NO ?*” will be displayed. 
Press the NEXT button or dial the CO number 
(01 through 12). 
“CO 01 : Fable” will be displayed. 
lack number 
Repeat pressing the m button until the 
desired jack number appears, or press the 
q button and then dial the jack number. 9. 0 
0  7. 
l To advance to the next jack number, 
press the m button. 
l To return to the previous jack number, 
press the B button. 
l To go to the desired jack number, 
press the 
q button and then dial the 
jack number. 
8. Repeat steps 5 to 7, to program the 
assignment of the other jack numbers. 
10. 
5. Press the SELECT button to alternate between 
“Enable” and “Disable” to select the desired 11. 
mode. 
6. Press the MEMORY button. 
The LCD will stop blinking. To advance to the next CO number, press 
the NEXT button. 
To return to the previous CO number, press 
the PREV button. 
1 To go to the desired CO number, press the 
SELECT button and then dial the CO 
number. 
Repeat steps 4 to 9, to program the 
assignment of the other CO numbers. 
To return to the initial program mode, press 
the END button. Programming Table 
Seepage7-13. . 
, 
,. 
I 
: 
3-49  
						

							Example: 
e 
Company XYZ would like incoming calls from the Central Office during the day mode to be received at 
the following zone. 
Zone Jack no. of Extension Programming CO no. 
A 01,02 01 
B 03,04 02 
C 0506 03 
Jack no. 05,06’N./’ 
Programming 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
All CO numbers have been set to 
( m or -IO11 m liiiG4..... . . . . . .  ) CO number 01 has been set to 
“Enable” on jack number 01. 
( m or jFF?i ) l5TF5lINIEMORYl...~ 
(lNEXTlorlG@5lLl)@l~lSELECTl 
( m or I#041 ) lsELECTl -I.... 
(LNEXTlorISELECTILGl)@lLllSELECTl 
( ISI or I ) lTELEE7 II\IIEMORY[.... CO number 01 has been set to 
. . . . . . . . . . . . . 
“Enable” on jack number 02. 
t 
m.... CO number 02 has been set to 
’ “Enable” on jack number 03. 
CO number 02 has been set to 
. . . . . . . . . . . . . “ 
Enable” on jack number 04. :. 
._:. c 
[MEMORYI. . . . CO number 03 has been set to 
’ “Enable” on jack number 05. 
CO number 03 has been set to 
. . . . . . . . . . . . . 
“Enable” on jack number 06. 
3-50  
						

							. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
until the desired CO number (01 though 12) appears 
(................................................... until the desired jack number appears 
PI : on jack number 01 
m : on jack number 32 
m : to assign the same on all 32 jacks 
until the desired mode appears 
Enable . . . . . . . . ..default (all 32 jack numbers) 
Disable 
or 
on all 32 jack numbers 
_..........,............................... . . 
1........................................,...................... 
III 32 : on jack number 32 
AB=m : to assign the same on all 12 CO’s 
Boll: on CO 01 
I= 11 .onCO12 
Description 
Through programming, you can select which 
extensions will ring on incoming calls from the 
Central Office during the night time. 
Programming 
1. Dial (48). 
“Night In CO” will be displayed. 
2. Press the NEXT button. 
“CO NO ? +” will be displayed. 
3. Press the NEXT button or dial the CO number 
(01 through 12). 
“CO 01 : #Ol : Enable” will be displayed. 
x 
jack number 
4. Repeat pressing the a button until the 
desired jack number appears, or press the 
- 7. 
l To advance to the next iack number. 
press the a button: 
l To return to the previous jack number, 
press the a button. 
l To go to the desired jack number, 
press the 
q button and then dial the 
jack number. 
8. Repeat steps 5 to 7, to program the 
assignment of the other jack numbers. 
9. 
l To advance to the next CO number, press 
the NEXT button. 
l To return to the previous CO number, press 
the PREV button. 
l To go to the desired CO number, press the 
SELECT button and then dial the CO 
number. 
10. Repeat steps 4 to 9, to program the 
5. 
6. k] button and then dial the jack number. 
Press the SELECT button to alternate between 
“Enable‘” and “Disable” to select the desired 
mode. 
Press the MEMORY button. 
The LCD will stop blinking. assignment of the other CO numbers. 
11. To return to the initial program mode, press 
the END button. 
Programming Table 
Seepage7-14. 
1 
, 
;. ;.: 
;; 
‘( ‘. 
3-51  
						

							w Selecting the “Normal” mode 
i ........................................ 
until the desired CO number (01 through 12) appears. 
: 
..................................... 
AB= q : to assign the same on all 12 CO’s 
lolo : on CO 01 
liJT1 :onCO 12 
w Selecting the “DIL” mode 
: ........................................ 
until the desired CO number (01 through 12) appears. 
:. ..................................... until the DIL mode appears 
Normal ............ ..defaul t (all 12 CO’s) 
DIL 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
mm r&T ~ I&l IMEMORY lm 
P I 1 
I 
1 I 
I 
a................................. AB= q : to assign the same on all 12 CO’s 
q Jzl : on CO 01 
pl‘n :onCO12 
Description 
Enables all outside line incoming calls to be directed to a specific extension phone 
(e.g., the assigned operator extension) during the day mode. 
By programming an outside line to the jack number of the corresponding extension 
phone, all incoming calls on that outside line will be received at the assigned 
extension phone. The call can be accepted by simply picking up the receiver. 
3-54  
						

							Programming 
w 
Selecting the “Normal” mode 
1. Dial (51). 
2. 
3. “CO Day/Mode” will be displayed. 
Press the NEXT button. 
“CO NO ?+” will be displayed. 
Press the NEXT button or dial the CO 
number (01 through 12). 
“CO 01 : Normal” will be displayed and 
“Normal” will blink. 
4. 
5. Press the SELECT button until 
the “Normal” mode is displayed. 
Press the MEMORY button. 
The LCD will stop blinking. 
6. To advance to the next CO number, 
press the NEXT button. 
To return to the previous CO number, 
press the PREV button. 
To go to the desired CO number, 
press the SELECT button and then dial 
the CO number. 
7. Repeat steps 4 to 6, to program the 
assignment of the other CO numbers. 
8. To return to the initial program mode, press 
the END button. w Selecting the “DIL” mode 1. Dial (51). 
“CO Day/Mode” will be displayed. 
2. Press the NEXT button. 
3. 
4. 
5. 
6. 
7. 
8. 
9. “CO NO ? +” will be displayed. 
Press the NEXT button or dial the CO 
number (01 through 12). 
“CO 01 : Normal” will be displayed and 
“Normal” will blink. 
Press the SELECT button until 
the “DIL” mode is displayed. 
“CO 01 : DIL : Jack-” will be displayed. 
Dial the jack number (01 through 32). 
Press the MEMORY button. 
The LCD will stop blinking. 
To advance to the next CO number, 
press the NEXT button. 
To return to the previous CO number, 
press the PREV button. 
To go to the desired CO number, 
press the SELECT button and then dial 
the CO number. 
Repeat steps 4 to 7, to program the 
assignment of the other CO numbers. 
To return to the initial program mode, press 
the END button. 
Programming Table 
See page 7- 19. 
L .:1 
: _: 
::::- 
3-55  
						

							Example: 
0 
Company XYZ would like incoming calls from Central Office During the day mode 
to be received by operators 1 and 2. 
Operator 1 has been connected to jack number 01. 
Operator 2 has been connected to jack number 02. 
I”“‘“’ 
KX-T123210 
Line 
Extension jack number 01 only has been set ’ 
1. a=[( lNEXTl or lo )lsELECTl1O11lG%GFFl.... 
to receive all incoming calls through CO 01. 
2. ( -1 or m 1021 ) lsELECTl 1011 II\IIEMORY.. . . . -. Extension jack number 01 only has been set 
to receive all incoming calls through CO 
02. 
3. ( m or I_ m ) IsELECT &I lNlEMoRV. .. . . . Extension jack number 02 only has been set 
to receive all incoming calls through CO 03. 
4. ( lNEXT or m Gl ) m 10 llhnEMoRV. . . . . . Extension jack number 02 only has been set 
to receive all incoming calls through CO 04. 
3-56  
						

							Programming 
n Selecting the “Normal” mode n Selecting the “DIL” mode 
1. 
Dial (52). 
2. 
3. “CO Night/ Mode” will be displayed. 
Press the NEXT button. 
“CO NO ?+” will be displayed. 
Press the NEXT button or dial the CO 
number (01 through 12). 
“CO 01 : Normal” will be displayed and 
“Normal” will blink. 
4. 
5. Press the SELECT button until the “Normal” 
mode is displayed. 
Press the MEMORY button. 
The LCD will stop blinking. 
6. To advance to the next CO number, 
press the NEXT button. 
To return to the previous CO number, 
press the PREV button. 
To go to the desired CO number, 
press the SELECT button and then dial 
the CO number. 
7. 
8. Repeat steps 4 to 6, to program the 
assignment of the other CO numbers. 
To return to the initial program mode, 
press the END button. 1. Dial (52). 
“CO Night/Mode” will be displayed. 
2. Press the NEXT button. 
“CO NO ?-+” will be displayed. 
3. Press the NEXT button or dial the CO 
number (01 through 12). 
“CO 01 : Normal” will be displayed and 
“Normal” will blink. 
4. Press the SELECT button until the “DIL” 
mode is displayed. 
“CO 01 : DIL : Jack-” will be displayed. 
5. Dial the jack number (01 through 32). 
6. Press the MEMORY button. 
The LCD will stop blinking. 
7. 
l To advance to the next CO number, 
press the NEXT button. 
l To return to the previous CO number, 
press the PREV button. 
l To go to the desired CO number, press 
the SELECT button and then dial the 
CO number. 
8. Repeat steps 4 to 7, to program the 
assignment of the other CO numbers. 
9. To return to the initial program mode, 
press the END button. 
Programming Table 
See page 7-19.