Panasonic Kx-T123210 Installation Manual

							Conditions 
l To erase all letters, press the CLEAR button. 
l To erase one letter, press the 
m button. 
l The maximum numbers’of letters can not exceed ten. 
Example: 
l To program jack number 01 for ........ Mr.Brown 
Display 
2. Dial (2). _............................................................... 
#Ol : 
2 
3. Press the SELECT button three times. . . . . . . . . . . . . . . . . I#01 : 
Bl 
4. Dial (7). _ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
~01 : 
B7 
5. Press the SELECT button four times. . 
#Ol : 
Br I 
6. Dial (6). _............................................................... 
#Ol : 
Br6 
7. Press the SELECT button six times. . . . . . . . . . . . . . . . . . . . . 
I 801 : 
Bro 1 
8. Dial (9). 
_............................................................... 
#Ol : 
Bro9 
9. Press the SELECT button two times. . . . . . . #o, : 
Brow 
10. Dial (6). ~.....................,.......................................... 
#Ol : 
Brow6 
11. Press the SELECT button four times. ,.................. 
#Ol : 
Brown 
12. _llENDl 
::; 
, 
:. 
There is a phone number directory on page 7-l 
3-69  
						

							. . . . . . . . . . . . . . . . 
until the desired jack number (01 through 32)appears. 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 
until the desired mode appears 
Option ‘.........’ default(all 32 jack numbers) 
Forced 
! . . . . . . . . . . . . *BE 
r;;l : to assign the same on all 32 jack numbers 
ml : on jack number 01 
@l’m : on jack number 32 
Description 
This feature gives each message of the SMDR 
an account code of the called or calling party. 
This feature has two modes “Forced” and 
“Option” .In the “Forced” mode, the account 
code must be entered every time extension 
user dials. 
In the “Option” mode, the account code may 
be entered when a record is needed. Refer to 
“Account Code” page 4-39. 
Programming 
Dial (64).  1. 
2. 
3. 
4. “Call Accounting” will be displayed. 
Press the NEXT button.’ 
“Jack NO?+” will be displayed. 
Press the NEXT button or dial the jack 
number (01 through 32). 
‘%Ol : Option” will be displayed and the 
-jack number 
“Option” will blink. 
Press the SELECT button to alternate 
between “Option” and “Forced” to select 
the desired mode. 5. Press the MEMORY button. 
The LCD will stop blinking. 
6. 
l To advance to the next jack number, 
press the NEXT button. 
l To return to the previous jack number, 
press the PREV button. 
l To go to the desired jack number, 
press the SELECT button and then dial 
the jack number. 
7. Repeat steps 4 to 6, to program the account 
code of the other jack numbers. 
8. To return to the initial program mode, press 
the END button. 
Programming Table 
See page 7-22. 
3-70  
						

							i ............................ until the desired jack number (01 through 32) appears. 
: .............................. until the desired mode appears 
Disable .......... ..defaul t (all 32 jack numbers) 
Enable 
: to assign the same on all 32 jack numbers 
: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 
Description 
Through programming, you can select whether an 
extension can transfer an intercom or outside call 
to another outside line manually. 7. 
Programming 
1. Dial (65). 8. 
“Transfer to CO” will be displayed. Repeat steps 4 to 6, to program the assignment 
of the other jack numbers. 
To return to the initial program mode, 
press the END button. 
2. Press the NEXT button. 
“Jack NO ?+ ” will be displayed. 
Programming Table 
See page 7-23. 
3. Press the NEXT button or dial the jack number 
( 01 through 32 ). 
“tiO1 : “Disable” will be displayed and “Disable” 
z jack 
number 
will blink. , 
4. Press the SELECT button to alternate between 
“Enable” and “Disable” to select the desired 
mode. 
5. Press the MEMORY button. 
The LCD will stop blinking. 
6. 
l 
0 
0 To advance to the next jack number, 
press the NEXT button. 
To return to the previous jack number, 
press the PREV button. 
To go to the desired jack number, 
press the SELECT button and then dial the 
jack number. 
3-71  
						

							l......................-unti I the desired jack number (01 through 32) appears 
............................. until the desired mode appears 
Disable .......... ..defaul t (all 32 jack numbers) 
Enable 
I~~NEXTIINEXT)~SELECT~IMEMORYIIENDI 
+ I 
,........................................... 
AB= q : to assign the same on all 32 jack numbers 
FjFl : on jack number 01 
jTjiyj : on jack number 32 
Description 
“Call Forwarding To Outside Line” (on page 7. Repeat steps 4 to 6 to program the 
4-28) can be enabled for each extension. assignment of the other jack numbers. 
Programming 8. To return to the initial program mode, 
press the END button. 
1. Dial (66). 
“CO Forward” will be displayed. 
2. Press the NEXT button. 
“Jack NO ? + ” will be displayed. 
3. Press the NEXT button or dial the jack number 
(01 through 32 ). 
“SO1 : Disable” will be displayed and “Disable” 
-E_ 
jack number 
will blink. 
Programming Table 
See page 7-23. 
4. Press the SELECT button to alternate between 
“Enable” and “Disable” to select the desired 
mode. 
5. Press the MEMORY button. 
The LCD will stop blinking. 
6. 
l To advance to the next jack number, 
press the NEXT button. 
l To return to the previous jack number, 
press the PREV button. 
l To go to the desired jack number, 
press the SELECT button and then dial the 
jack number. : 
;- 
: 
.‘_. _: 
-: : 
3-72  
						

							:...............- ............ 
until the desired jack number (01 through 32) appears 
i.. ........................... until the desired mode appears 
Disable .......... ..default(al I 32 jack numbers) 
Enable 
AB= r;;l : to assign the same on all 32 jack numbers 
lolli-1 : on jack number 01 
m’j-5-1 : on jack number 32 
Description 
This feature can dial to the extension that is setting 
the Do Not Disturb by programming. 
Refer to “Do Not Disturb Override” on page 4-31. 
Programming 
1. Dial (68). 7. 
8. 
“DND Override” will be displayed. Repeat steps 4 to 6, to program the 
assignment of the other jack numbers. 
To return to the initial program mode, 
press the END button. 
2. Press the NEXT button. 
“Jack NO ? + ” will be displayed. 
3. Press the NEXT button or dial the jack 
number ( 01 through 32 ). 
“#Ol : Disable” will be displayed and “Disable” 
-c_ 
jack number 
will blink. 
Conditions 
This feature allows you to ring an extension that is 
set for the “Do Not Disturb” mode. 
Programming Table 
See page 7-24. 
4. Press the SELECT button to alternate 
between “Enable” and “Disable” to select the 
desired mode. 
5. Press the MEMORY button. 
The LCD will stop blinking. 
6. 
l To advance to the next jack number, 
press the NEXT button. 
l TO return to the previous jack number, 
press the PREV button. 
l TO go to the desired jack number, 
press the SELECT button and then dial the 
jack number. 
3-74  
						

							Doorphone Feature 
,..................................... 
until the desired doorphone number (1 or 2) appears 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
until the desired jack number appears 
m : on jack number 01 
m[ : on jack number 32 
m : to assign the same on all 32 jacks 
. :i, 
until the desired mode appears 
. . . . . . . . ..default (all 32 jack numbers) 
Description 
Allows each extension to be programmed for 
receiving calls from up to 2 doorphones during 
the day mode. 
(Doorphone is an option.) 
Programming 
Dial (70). 1. 
,2. 
3. 
4. 
5. “Day Door Phone” will be displayed. 
Press the NEXT button. 
“Door NO ? +” will be displayed. 
Press the NEXT button or dial the doorphone 
number (1 or 2). 
“DP-1:~Enable” will be displayed. 
jack number 
Repeat pressing the m button until the 
desired jack number appears, or press the 
I#I button and then dial the jack number. 
Press the SELECT button to alternate between 
“Enable” and “Disable” to select the desired 
mode. 
3-75 
6. Press the MEMORY button. 
The LCD will stop blinking. 
7. 
l To advance to the next jack number, 
press the m button. 
l To return to the previous jack number, 
press the w button. 
l To go to the desired jack number, 
press the 
q button and then dial the 
jack number. 
8. Repeat steps 5 to 7, to program the assignment 
of the other jack numbers. 
9. Repeat steps 3 to 8, to program the assignment 
of the another doorphone. 
10. To return to the initial program mode, press the 
END button. 
Programming Table 
See page 7-24.  
						

							j”^i___~“.~-.. ___..-- _i 
,......................... 
. . . . . . . . . . ..until the desired doorphone number (1 or 2) appears 
,.................................................. until the desired jack number appears 
m : on jack number 01 
@ : on jack number 32 
I# : to assign the same on all 32 jacks 
until the desired mode appears 
Description 
Allows each extension to be programmed for 
receiving calls from up to 2 doorphones during the 
night mode. 
-(Doorphone is an option.) 6. Press the MEMORY button. 
The LCD will stop blinking. 
7. o To advance to the next jack number, 
press the m button. 
Programming 
1. Dial (71). 
“Night Door Phone” will be displayed. 
2. Press the NEXT button. 
“Door NO ? +” will be displayed. 
3. Press the NEXT button or dial the doorphone 
number (1 or 2). 
“DP-1 :Fnable” will be displayed. 
lack number 
4. Repeat pressing the m button until the 
desired jack number appears, or press the 
q button and then dial the jack number. 8. 
l To return to the previous jack number, 
press the m button. 
l To go to the desired jack number, 
press the 
q button and then dial the 
jack number. 
9. 
10. Repeat steps 5 to 7, to program the assignment 
of the other jack numbers. 
Repeat steps 3 to 8, to program the assignment 
of the another doorphone. 
To return to the initial program mode, press the 
END button. 
5. Press the SELECT button to alternate between 
“Enable” and “Disable” to select the desired 
mode. 
Programming Table 
See page 7-25. 
3-76  
						

							until the desired mode appears 
Hold-l ...........Flash hookswitch 
only . . . . . . . . . . . . . . . . . . . . . . . . . default 
Hold-2 ..=........Flash hookswitch and dial 20 -1 
I Description 
If a standard telephone at the extension ring 
immediately after hanging up or about 30 set 
later, this programming step will eliminate the 
problem by requiring the extension to dial 20 
after hook flashing in the Hold-2 mode. 
The following operation is changed when 
“Hold-2” mode is set. 
Call Park (on page 5-4) 
Call on Hold (on page 5-4) 
Conference (on page 5-5) 
Call Waiting (on page 5-5) 
Call Splitting (on page 5-6) 
Call Transfer (on page 5-6) 
Paging And Transfer (on page 5-8) 
External Feature Access (on page 5-9) 
Account Code (on page 5-10) 
Programming 
1. Dial (91) 
“Option” will be displayed. 
2. Press the NEXT button. 
“Hold-l” will be displayed and blink. 
3. Press the SELECT button to alternate 
between “Hold-l” and “Hold-2” to select 
the desired mode. 
4. Press the MEMORY button. 
The LCD will stop blinking. 
5. To return to the initial program mode, press 
the END button. 
Programming Table 
See page 7-25 
3-77  
						

							l All Parameters 
0 System Parameter 
l Speed Call until the desired mode appears 
All Para . . . . . . . . . . . default 
System Para 
co Para 
EXT 
Para 
DSS Para 
Speed Call 
l CO Parameter (Outside) 
,.............. . . . . . . 
until the CO Para appears 
- to assign the same on all 12 CO’s 
n~~n~~~ 99 NEXT SELECT MEMORY AB MEMORY END 
t 
l Extension Parameter 
I....................-until the EXT Para appears 
. 
: ‘AB= 
q : to assign the same on all 32 jack numbers 
mm : on jack number 01 
m.z[ : on jack number 32 
l DSS Parameter 
~......................until the DSS Para appears 
;““‘-. A= 
q : to assign the same on both DSS’s 
111 :onDSSl 
cl 2 :onDSS2 
ElnnnIp’~I 99 NEXT SELECT MEMORY A MEMORY END 
T I 
3-78