Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. System Programming (FFl)Section 400-Programming
Tl Trunk Type Emulation
Software Version:CPC-6 Version 4.0 or higherAddress: 
FFl 8# 4# 6# (Trunk)## 1# (OS)#
DescriptionDetermines the type of trunk signaling that each Tl channel emulates (E&M
by default).
Programming
I
Notes
FFl 8# 4## 6# (1164)# l# (013)#
f+
Trunk Number (l-64)O=Loop start
1 =ireserved for-future use)
2=Ground Start (used for
ground start emulation)
3=E&M
Power-Cycling Requirement.For changes to this parameter to take...

Section 400-ProgrammingChapter 1. System Programming (FFl )
DID/DNS
Software Version:CPC-B Version 4.0 or higherAddress: 
IFFi W 4# W (Trunk)# 2# (O-2)#
DeskiptionUse this address to enable trunks for DID or DNIS calls.l
If DID is seiected, the system will use the DID Numbers Table (see FFl
8# 3#) to detemine which extension(s) will receive the DID call.l
If DNTS is selected (available only with Tl interface), the system will
use the DNIS Numbers Table (see FFl 8# 4# 7#) to determine which
extension(s)...

Chapter 1. System Programming (FFl)Section 400-Programming
Soha= k~;xi~n:CPC-B Version 4.0 or higherAddress: 
#-I T r;a# 4# 6# (Truwk)# 3# (012)#
DescriptionDetermines the signaling class used by Tl channels on outgoing calls
(Immediate Start by de&&).’
Programming
FFI 8# 4# 6# (144)# 3# (0-2)#
f
Trunk Number (l-64)O=Immediate Start.
l=Wink start.
2=Dial Tone Start.
CO Requirement.The Outgoing Type setting must match what is ordered
f?om the CO..
Power-Cycling Requirement.For changes to this parameter to...

Section 400-Programming
Chapter 1. System Programming (FFl)
Incoming Signaling Type
Software Version:CPC-8 Version 4.0 or higherAddress: 
FFI 8# 4# 6## (Trunk)# 4#I (0 or I)#
DescriptionDetermines the signaling class used by Tl channels on incoming calls
(Immediate Start/Ringdown by default).
Programming
r
Notes
FFI 8# 4# 6# (I-64)# 4# (0 or l)#
f+
Trunk Number (l-64)O=Immediate Start/
Ringdown.
l=Wink Start.
CO Requirement.The Incoming Type setting must match what is ordered
from the CO.
Power-Cycling...

Chapter 1. System Programming (FF’l)Section 400-Programming
Trunk Mode
Software Version:CPC-6 Version 4.0 or higherAddress: 
FFI 8# 4#I 6# (Trunk)# 5# (0 or l)#
DescriptionDetermines whether Tl channels are used for only outgoing calls, or for both
incoming and outgoing calls.
Programming
I
FFI 8# 4# 6# (l-64)# 5# (0 or l)#
f+
Trunk Number (l-64)O=Incoming and Outgoing.
l=Outgoing only.
NotesPower-Cycling Requirement.For changes to this parameter to take effect,
the system must be turned off, then back...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Robbed Bit Setting
Software Version:CPC-B Version 4.0 or higherAddress: 
FFl 8# 4## 6# (Trunk)# 6# (0 or l)#
DescriptionThe Robbed Bit Setting determines if AB or ABCD signaling is used.
AB/ABCD signaling robs bits from the 
Tl channels, and uses those bits to
transmit signaling information. SF 
(SuperFrame) normally uses AB
signaling; ESF (Extended 
SuperFrame) normally uses ABCD signaling.
Programming
I
FFl 8# 4# 6# (l-64)# 6# (0 or l)#
i(lr...

Chapter 1. System Programming (FFl)Section 400-Programming
Incoming Dialing Method
Software Version:CPC-B Version 4.0 or higher
Address:FFl 8# 4# 6# (Trunk)# 7# (0 or l)#
DescriptionDetermines whether the system expects dial-pulse or DTMF digits for
incoming DID or DNIS calls over the 
Tl.
Programming
I
FFl 8# 4# 6# (1164)# 7# (0 or l)#
ff
Trunk Number (l-64)O=Dial-Pulse (10 PPS)
l=DTMF
NotesPower-Cycling Requirement.For changes to this parameter to take effect,
the system must be turned off..then back...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Dial Tone Transmission
Software Version:
CPC-B Version 4.0 or higher.Address: 
FFl 6# 4# 6# (Trunk)#I W (0 or l)#
DescriptionThis address is reserved for future use.
DBS-70-400DBS Manual - Issued 8/l/95Page 1-193 

Chapter 1. System Programming (FFl)Section 400-Programming
Busy Tone Transmission
Software Version:
CPC-B Version 4.0 or higherAddress: 
FFl 8# 4# 6# (Trunk)# 9# (0 or l)#
DescriptionThis address is reserved for future use.
Page 1-194DBS Manual - Issued 8/l/95.DBS-70-400 

Section 400-ProgrammingChapter 1. System Programming (FFi)
Dial Tone Receive
Software Version:CPC-B Version 4.0 or higherAddress: 
FFl 8# 4# 6# (Trunk)# lO# (0 or l)#
DescriptionDetermines whether dial tone is transmitted from the DBS Tl channel to DBS
stations.
Set this address to “On” only if the far end does not provide Tl dial tone.
Programming
I
I
FFl 8# 4# 6# (l-64)# 1 O# (0 or l)#
f+
Trunk Number (1-64)O=Off
l=On
NotesOr&ring Tones From Carrier.If a carrier is supplying Tl services, always
order...