Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. System Programming (FFl)Section 400-Programming
Ringback Tone Transmission
Software Version:
CPC-B Version 4.0 or higher
Address: 
FFl 8## 4#I 6# (Trunk)# 11# (0 or l)#DescriptionDetermines whether 
ringback tone is transmitted from the DBS Tl channel to
the CO.Set this address to “On” only if the far end does not provide 
ringback tone.
Programming
I1
FFI 8# 4# 6# (l-64)# 11# (0 or l)#
4/+Tmnk Sumber 
i l-64)&Off
l=On
NotesOr&ring Tones From Currier.If a carrier is supplying Tl services,...

Section 400~ProgrammingChapter 1. System Programming (FFl)
DNIS Number Setting
Software Version:CPC-B Version 4.0 or higherAddress: 
FFl 8## 4## 7# (DNISNo.)# (ExtNo.)#
DescriptionUse this address to assign DNIS number(s) to extension(s).
lUp to 500 different DNIS numbers can be assigned.
lOne DNIS number can be assigned to multiple extensions (this takes up
only one entry in the 500 available entries).
lOne extension can have multiple DNIS numbers assigned to it. (The
number of entries taken up is equal...

Chapter 1. System Programming (FFl)Section 400-Programming
DlDlDNlS Flexible Ringing Assignments
Sofbvare Version:CPC-B Version 5.0 or higherAddress: for DID:
FFl 8# 5# (DIDNo.)# (ExtNo.)# (OOOO[OO]-llll[Sl])#
for DNIS:
FFl 8# 6# (DNISNo.)# (ExtNo.)# (OOOO[OO]-llll[ll])#
DescriptionThis address allows you to enable or disable ringing for specific DID/DNTS
numbers during Day, Night and Night 2 modes. This also applies to delayed
ringing.
Note: The DID/DNIS number must already be assigned to an extension...

Section 400-Programming
Chapter 1. System Programming (FFl)CO Delayed Ring Timer: 
FFl 3# 26# (0-15)#Inbound DID Dial Numbers: 
FFl 8# 3# (D1DNo.H (ExtNo.)#
DID/DNIS (enabling trunks for): FFl 8# 4# 6# (Trunk)# 2# (0-2)##
DNIS Number Setting: FFl 8# # 7# (DNISNo.)# (ExtNo.)#
NotesDelayed Ring Timing.Timing for DID/DNIS delayed ringing is controlled
by the CO Delayed Ring Timer 
(FFl 3# 26# O-l%).
DBS-70-400DBS Manual - issued 8/l/95Page l-199 

Chapter 1. System Programming (FFl)Section 400-Programming
.
Tl Trunk Closure
Software Version:WC-B Versions 5.0 to 6.02Address: Master Cabinet: 
FFl 8# 7# 1# (l-4)# (118)# (0 or l)#
Slave Cabinet:FFl 8# 7# 2# (l-4)# (1,8)# (0 or l)#
DescriptionIn CPC-B Versions 5.0 to 6.02, use this address to facilitate Fractional Tl,
where not all of the 24 available channels on the Tl card are used.
Lf the trunk ports on the highest-numbered analog trunk card are divided
between 
Tl and analog, use this address to...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Programming
rI
FFl 8#7#
l=Master Cabinet
2=Slave Cabinet
Trunk SlotT&k PortO=Open
on Cardl=Close
Related Programming
Trunk Configuration:FFl 8# 4## (4 or 5)# l# l# (0 or l)#Number of 
Tl Channels: FFl 8# 4## (4 or 5)# l# 2# (0-24)#
Trunk Circuit Type: FF2 
(Trunk)# 21# (0-3)#
NotesLoop-Start Card Version Requirement.This Tl Trunk Closure address
can only be used with the VB-435 
10A or VB-43511A versions of the loop-
start card.
CPC-B Versions...

2. Trunk Programming (FF2)
Use the FF2 programming addresses in this chapter to set parameters for the
CO trunks of the DBS system.
Most of these FF2 addresses require a trunk number and/or extension port
entry. The acceptable range of trunks/extension ports varies according to the
configuration of your DBS system. In this chapter, the range used for trunks
is l-64. which is the maximum available number of trunks in a DBS 96 +
DBS 96 system with a CPC-B card. The range used for extension ports is
1-144,...

Page 2-2
DBS Manual - Issued 8/l/95*DE!%70-400
‘\ 

Trunk Port Operation
Software Version: All VersionsAddress: FF2 
(Trunk)# l# (0 or l)#
DescriptionUse this feature to put a CO trunk in service or “busy it out”.
ProgrammingFF2 
(li”” 1# (0 y l)#
Trunk NuniberO=Place trunk in service.
l=Busy-out the trunk.
NotesPrecaution on Putting Lines Out of Service.If you busy-out a trunk, an
incoming caller on that trunk will still hear ringing, even though the trunk is
not functional.
D BS-70-400DBS Manual - Issued 8/l/95Page 2-3 

DTMF/PuIse Dialing for Trunks
Software Version: All VersionsAddress: FF2 (Trunk)# 
2# (0 or l)#
DescriptionUse this feature to set a trunk for DTMF or pulse dialing (10 pulses per
second).
Programming
I
Trunk NumberO=DTMF
l=Pulse dialing (10 pps)
Notes-Door Box Adapter Setting.CO trunk ports used for Door Box Adapter
Sensors should be set for “Pulse dialing”.
Page 2-4DBS Manual - Issued 8/l/95DBS-70-400