Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Trunk Port ClassSoftware Version:CPC-B Version 4.0 or higherAddress: FF2 (Trunk)# 
26# (418)#
DescriptionThis parameter is provided in case a specific trunk or group of trunks needs a
unique pad level. This will only work if the Sync unit (VB-43563) is installed
piggyback on the CPC-B card.
By default, DBS trunks are assigned a circuit type, based on whether they are
analog or 
Tl. This circuit type is used in the Digital Pad Settings address
(FFl 8# 4# 3#) to determine the loss/gain settings for...

Chapter 2. Trunk Programming (FF2)Section 400-Programming
Related Programming
Digital Pad Settings:FFl 8# 4# 3# (l-12)# (l-12)# (O-30)++Station Port Class: FF3 
(ExtPort)# 37# (l-2 or 7-8)#
NotesExtension Circuit Types.Circuit types can also be assigned to extension
ports. See the 
Station Port Class address for more information.
Page 2-26
DBS Manual - Issued 8/l/95DBS-70-400 

3. Extension Programming (FF3)Use the 
F’F3 programming addresses in this chapter to set parameters for
extensions.All 
FF3 addresses require an extension port entry. The acceptable range for
extension ports depends on your DBS system’s configuration. 
In this chapter,
the range shown for extension ports is 
(l-144), which is the maximum
available number of extension ports in a DBS 96 + DBS 96 system with a
CPC-B card. With a CPC-AII card, the maximum range is (l-72) extension
.ports. For more...

,
FF3 (ExtPort)# 3% (0-8)##Extension class of Service Assignment3-40
(CPC-AWE 3.1 or higher)
FF3 (ExtPon)# 3% (OOOO-9999)#Inbound DID Dial Numbers(CPC-8 2.0 only)341
FF3 (ExtPoIt)# 3% (0 or 1)#AEC Disconnect(CPC-A 3.3 or higher)3-41
FF3 (ExtF’ort)# 36# (0-2)#Ringback Tone From ML Keys3-42
(CPC-AII/B 2.0 or higher)
FF3 (Extl’ott)# 37# (1-2 or 7-8)#Station Port Class(CPC-B 4.0 or higher)3-43
FF3 (ExtPort)# 38# (0 or l)#SLT Hookflash(CPC-B 3.1 or higher)3-45
FF3 (ExtPort)# 39# (O-9)++Extension Ring...

Section 400~ProgrammingChapter 3. Extension Programming (FF3)Extension Numbers
Software Version: All VersionsAddress: FF3 (ExtPort)# 
1# (lo-69 or lOO-699)#
DescriptionThis program assigns an extension number to an extension port.
lAn extension number is the 2-digit or 3-digit number that is dialed to reach
the extension phone. Extension numbers are programmable and can be
changed.
lAn extension port is the physical location (RJ2lx on the DBS connector)
into which the phone is plugged. Extension ports...

Chapter 3. Extension Programming (FF3)Section 400-Programming
NotesPrimary Attendant Extension.The default extension number for the
Primary Attendant is 10 or 100, assigned to port 1. It is not possible to
change the Primary Attendant’s extension number or port. The Primary
Attendant phone must be a key telephone with an LCD display.
Second Attendant Extension.If a Second Attendant is assigned, its default
extension number is 11 or 101, assigned to port 2. Although the Second
Attendant assignment can be...

Section 400~ProgrammingChapter 3. Extension Programming (FF3)
Terminal Type
Software Version: All VersionsAddress: FF3 (ExtPort)# 
2# (ExtType)#
DescriptionSome DBS extensions are automatically configured when installed on an
extension port. This address allows you to change default terminal
assignments, or assign special equipment to extension ports.
ProgrammingFF3 
(lj144)# 2# (ly)#
IExtension PortTerminal Type (see table below)Table 3-1. 
Terminal Types
Note:If the configuration is “Auto”, the system...

Chapter 3. Extension Programming (FF3)Section 400-Programming
31-38Integrated Auto Attendant channels
39-40(not used)
41-48Integrated DBS Voice Mail channelsAuto
N/A
Auto
Related Programming
APVAEC Slot Assignment: FFl 2# l# 20# (2-9 or
NotesTerminal Type 6 (DSLT).This terminal type is not available in CPC-A/B
versions prior to 3.1.
Terminal Type IO (Third-Party Voice Mail).Beginning with CPC-A
Version 3.28 and CPC-B Version 4.07, when an analog port hookflashes to
return to a held trunk, the DBS returns...

Section 400~ProgrammingChapter 3. Extension Programming (FF3)EM/24 Port Assignment
Software Version: All VersionsAddress: FF3 (ExtPort)# 
3# (ExtPort)#
DescriptionThis program assigns an EM/24 terminal to a key phone by associating the
extension ports.
EM/24 terminals provide additional FF keys to a key phone. An EM/24
terminal needs its own extension port. This address therefore requires two
port number entries --one for the EM/24 terminal, and one for the key phone.
After the EM/24 is assigned to the...

Chapter 3. Extension Programming (FF3)Section 400-Programming
Forced Least Cost RoutingSoftware Version: All Versions
Address: FF3 (ExtPort)# 
4# (0 or l)#
DescriptionUse this address to set individual extension(s) for forced Least Cost Routing
(LCR).
If an extension is set for forced LCR:
levery pooled key “9” is now an LCR key.
lstations cannot dial 8 l-86 to place an outside call.
lthe caller will hear a dial tone generated by the DBS -- but the system will
not access an outside line until the caller...