Panasonic Cpc+AII/B Digital Business System Release Notes Manual

3ecuon 4uu-rrogrammingc;naprer 2. i runK rrogramming (i-qPooled Trunk Access for Group 
“9”
Software Version: All VersionsAddress: FF2 (Trunk)# 
3# (0 or l)#
DescriptionUse this feature to place a trunk in a group from which trunks are
automatically chosen for outbound dialing. When you dial 
“9” from an SLT
or digital extension, or press an FF key that is set as a pooled trunk key, any
available trunk in the group will be accessed.
The trunk selection is made from the 
highest trunk number in the group...

Chapter 2. Trunk Programming (FF2)Section 400-Programming
Pooled Trunk Access for Groups 1L81-86”Software Version: All Versions
Address: FF2 (Trunk)# 
(419)# (0 or I)#
DescriptionUse this feature to place a trunk in a group from which trunks are
automatically chosen for outbound dialing. When you dial 
81,82,83,84,85,
or 86 from an SLT or digital extension, or press an FF key that is set as a
pooled trunk key, any available trunk in the group will be accessed.
The trunk selection in a particular group is...

Section 400-ProgrammingChapter 2. Trunk Programming (FF2)Trunk Port Type
Software Version: -All VersionsAddress: FF2 (Trunk)# 
lO# (1 or 2)#
DescriptionEach trunk port must be identified as a regular CO trunk or as a PBX line.
Programming
.FF2 (I-64)# lO# (1 or 2)#
t t
Trunk Numberl=Regular (CO) trunk
2=PBX line
Related ProgrammingAuto Flash 
R&al: FFl 2# l# 6# (0 or l)#PBX Access Codes: 
FFl 2# 3# (l-8)# (O-999 or 0* to 99*)#
Automatic Pause Position for PBX Access Codes: FFl 2# 3# (9-18)#...

Chapter 2. Trunk Programming (FF2j
Section 400-Programming
DISA Auto Answer
Software Version: All VersionsAddress: FF2 
(Trunk)# ll# (0 or l)#
DescriptionUse this feature to set a trunk(s) to automatically provide DISA tone upon
connection with an inbound caller.(However, after hearing the DISA tone,
the caller will still have to enter an ID code in order to use DISA.)
If a trunk is set to provide DISA tone, you can limit DISA operation on that
trunk to a certain number of hours each day, using the DISA...

Section 400-ProgrammingChapter 2. Trunk Programming (FF2)Private Trunk Line
Software Version: All VersionsAddress: FF2 
(Trunk)# 12# (ExtPort)#
DescriptionUse this address to assign a private trunk line to an extension. A number of
private trunks can belong to one extension.
Once a private trunk is assigned to an extension, other extensions cannot
make outbound calls or receive inbound calls on that trunk (the system 
wili
assign Toll Restriction Type 0 to the trunk on all other extensions). The
system...

bnaprer 2. I ruiln rrogrammlng (rrq3ecwtl 4uu-rrogrammlng
Automatic Pause for PBX Line
Software Version: All VersionsAddress: FF2 (Trunk)# 
13# (0 or l)#
DescriptionThis address determines if a pause is automatically inserted during the dialing
of a PBX access 
code.
If this address is enabled, the system will automatically pause after dialing the
first, second, or third digit of the PBX access code. See the PBX Access
Code(s) address (FFl 2# 3# 9-18# l-3#) for more information.
If this address is...

Dial Tone Detection
Software Version: All VersionsAddress: FF2 (Trunk)# 
14# (0 or l)#
DescriptionThis program determines when dialed digits are outpulsed -- either according
to the Dial Pause Timer setting 
(FFl 3# 17#), or after the DBS detects dial
tone.
Programming
FF2(I-64)#14#I (0 or l)#
Trunk NumberO=Digits are outpulsed according to the
Dial Pause Timer.
l=Digits are outpulsed after dial tone
is detected.
.Related Programming
Dial 
PauseTimer: FFl 3# 17# (0-15)#DBS-70-400DBS Manual 
- Issued...

Outbound DTMF Signal Duration for Auto-Dialed Digits
Software Version: All VersionsAddress: FF2 (Trunk)# 
15# (1.3)#
DescriptionThis address controls DTMF signal duration when digits are dialed
automatically by the system rather than the user.
Examples of DBS dialing include:l Redial
l Saved Number Redial
l Speed Dialing
l Adding LCR digits
Programming
IFF2 
(I-64)# 15# (113)#
tt
Trunk Number1=75 ms on/50 m off
24125 ms on/125 ms off
3=250 ms on/250 ms off
NotesDTMF Tone for Manual Dialing.If you dial...

Section 400-Programming
Chapter 2. Trunk Programming (FF2)
Unsupervised Trunk Conference
Software Version: All VersionsAddress: FF2 (Trunk)# 
16# (0 or l)#
DescriptionUse this feature to enable trunk(s) to be used in an unsupervised conference
call.
Pro,grammingFF2 
(l-64)# 16# (0 or l)#
ft
Trunk NumberO=The CO’trunk cannot be used for
an unsupervised conference.
l=The CO trunk can be used for an
unsupervised conference.
Notes
automatically disconnected according to the Unsupervised Conference Timer...

bIlaprttr L. I runK rrograrrwaiiy 	t-2)3w.xu11 4uu-rroyrairirriirig
Inbound Ring Pattern
Software Version: All VersionsAddress: FF2 (Trunk)# 
17# (0-9)#
DescriptionEach CO trunk can be assigned a distinctive ring pattern for easy recognition
of the trunk during an incoming call. Up to 9 different ring patterns are
available.
Programming
rFF2 
(1164)# 17#
f
Trunk Number
Inbound Ring Pattern
Default: 0 (determined by CO)
(see the following table)
Table 2-1.Ring P&ems for inbound trunk calls
Notes...