Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. System Programming (FFl)Section 400-Programming
Table l-47. Digital Pad Setthgs - pad numbers and related dB levels
Table l-48. Digital Pad Settings 
- default values
Related ProgrammingTrunk Port Class: FF2 
(Trunk)# 26# (4-8)#Station Port Class: FF3 
(ExtPort)# 37# (l-2 or 7-8)#
Page 1-156DBS Manual - Issued 8/l/95DBS-70-400 

Section 400-ProgrammingChapter 1. System Programming (FFl)
NotesExample Digital Pad Adjustment.If calls to SLTs via a master Tl have low
volume levels, the pad levei for connections from the master Tl to all SLTs
can be changed.
By default, the pad level for connections from the master 
Tl to all SLTS is 16
(or -2 dB). To raise the volume by 2 d.B, change the pad value to 0 (or 0 dB)
by programming the following:
FFl 8# 4# 3## 2# !5f# O##
where:2% is the circuit type for SLTs;
5# is the circuit type for...

Chapter 1. System Programming (FFl)Section 400-Programming
Trunk Configuration
Software
Version:CPC-BVersions
4.0to6.02Address: Master Cabinet: 
FFl 8# 4## 4## 1# I# (0 or l)#
Slave Cabinet:FFl 8# 4# 5# 1# 1# (0 or l)#
DescriptionSpecifies the trunk combinations used in the DBS system (analog trunks only
by default).
Setting this address to “Tl and Analog trunks” tells the DBS system that Tl
and analog trunks are being used in the same cabinet. (Each Tl channel uses
up one trunk port on the analog trunk...

Section 400-Programming
Chapter 1. System Programming (FFl)
Number of Tl ChannelsSoftware Version: CPC-B Version 4.0 or higher
Address: Master Cabinet: 
FFl 8# 4# 4## 1# 2# (0-24)#
Slave Cabinet:
FFl 8# 4# 5# l# 2# (O-24)#
DescriptionThis program determines how many TI channels will be used in the DBS
system. This address provides “Fractional 
Tl” capability -- using only a
portion of the 24 available channels on the 
Tl card.
Since each 
Tl channel used will need one analog trunk port dedicated to it,...

Chapter 1. System Programming (FFl)Section 400-Programming
Frame Format
Software Version: CPC-6 Version 4.0 or higherAddress: Master Cabinet: 
FFl 8# 4# 4# l# 3# (0 or l)#
Slave Cabinet:FFl 8# 4# 5# l# 3# (0 or l)#
DescriptionSelects the framing format used by the Tl. Either “Superframe” (SF) or
“Extended Super-frame” (ESF) can be selected.
The SF consists of 12 frames, with each frame including 192 information bits
and 1 framing bit. The ESF consists of 24 
frames (double the length of the SF
format)....

Section 400-ProgrammingChapter 1. System Programming (FFI)
Line Coding
Software Version:CPC-B Version 4.0 or higher.Address: Master Cabinet: 
FFl 8# 4# 4# 1# 4# (0 or I)#
Slave Cabinet:FFl 8# 4## 5## l# 4# (0 or l)#
DescriptionSelects the line coding format used by the Tl. Either “BSZS” (binary g-zeros
suppression) or “AMP (Alternate Mark Inversion) can be selected. 
In most
cases (and by default), 
AMI is used.
Programming
I~
Notes
FFl 8# 4# (4 or 5)# l# 4# (0 or l)#
ff
4=Master Cabinet
5=Slave Cabinet...

Lnapter 1. System Programming (FFl)sectlon 400~Programming
Failure Mode
Software Version:CPC-6 Version 4.0 or higherAddress: Master Cabinet: 
FFl 8# 4## 4## I# 5# (0 or l)#
Slave Cabinet:FFl 8# 4# 5# l# W (0 or l)#
DescriptionDetermines the way the system responds to alarms. By default, the system
will continue to operate even if errors are detected.
Programming
I
FFl 8# 4## (4 or 5)# 1# 5# (0 or I)#
ff
4=Master Cabinet
5=Slave Cabinet
O=Mode 1 (the Tl continues to
operate even if errors
are detected)...

Section 400-Programming
Chapter 1. System Programming (FF1)
Remote Loopback
Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: 
FFl 8# 4#I 4# l# 6# (0 or l)#
Slave Cabinet:FFl 8# 4# 5# l# 6# (0 or l)#
DescriptionThis address is reserved for future use.
DBS-70-400DBS Manual - Issued 8/l/95.Page l-163 

Chapter 1. System Programming (FFl)Section 400-Programming
Yellow Alarm Send
Software Version:
CPC-B Version 4.0 or higherAddress: Master Cabinet: 
FFl 8# 4## 4# 1# 7# (0 or l)#
Slave Cabinet:FFl 8# 4## 5# 1# 7W (0 or l)#
DescriptionDetermines whether the DBS sends a yellow alarm signal to the CO.
A yellow alarm is sent to the distant end of the 
Tl link to indicate that a red
alarm has occurred. If a red alarm occurs at the CO, the CO sends a yellow
alarm to the DBS. If a red alarm occurs at the DBS,...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Flash Key Operation
Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: 
FFl 8## 4## 4## l# 8# (0 or l)#
Slave Cabinet:FFl 8## 4# 5# 1# 8# (0 or l)#
DescriptionIn the current version of DBS Tl, a “switchhook flash” releases and reseizes
the 
Tl line.
Programming
11
FFl 8# 4#I (4 or 5)# l# 8# (0 or l)#
$$
4=Master CabinetO=Release and reseize
5=Slave Cabinetl=Reserved for future use
DBS-70-400DBS Manual - Issued 8/l/95Page 1-165