Panasonic Cpc+AII/B Digital Business System Release Notes Manual

NIGHT Key Operation.If only one of the Auto Mode Start Times is set, the
Attendant NIGHT key can be used to manually switch to another mode. For
instance, if Night mode has been activated automatically, the Attendant can
press the NIGHT key to go into Day mode. (However, the Attendant must
wait at least 3 minutes after the mode is automatically activated, before using
the NIGHT key to switch the mode again.)
In 
CPC-AII/B versions prior to 7.0, if both Auto Day and Auto Night Mode
Start 
Ames are set,...

Section 400-Programming
Chapter 1. System Programming (FFl)
Programming and DISA CodesRemote Programming ID Code
Software Version: All VersionsAddress: 
FFl 4## (0000-9999)#
DescriptionThe Remote Programming ID Code allows you to enter the terminal
programming mode. This programming mode is used to enter programming
commands from a remote PC or a 
local PC connected directly to the SMDR
port (CN6).
You can enter the remote programming mode through any of these three
methods:
lBy dialing into the system...

Chapter 1. System Programming (FFl)Section 400-Programming
DISA Inbound Call ID Code
Software Version: All VersionsAddress: 
FFl 5## (0000-9999)#
DescriptionUse this address to set a valid ID code for inbound DISA (Direct Inward
System Access) callers. By default, no ID code is defined. which means a
caller who dials a DISA trunk will receive intercom dial tone immediately
without entering an ID code.
If you define a DISA Inbound Call ID Code in this address, callers dialing in
on the 
DISA trunk will...

Section 400-ProgrammingChapter 1. System Programming (FFl)
DISA Outbound Call ID Code 1
Software Version: All VersionsAddress: 
FFl 6## l# (0000-9999)#
DescriptionOnce a caller has dialed in on the DISA trunk and accessed intercom dial
tone, he/she can access a trunk line by dialing 
#7, then the ID code set in this
address (1111 by default), then 9 or 81-86 to access the 
MC0 trunk.
Programming
To set DISA Outbound ID Code 1 . . .
IFFl 6# l# (0000;9999)#
4-Digit DISA Outbound ID Code 1
(Default: 1111)...

Chapter 1. System Programming (FFi)Section 400-Programming
DISA Outbound Call ID Code 2
Software Version: All VersionsAddress: 
FFl 6## 2# (OOOO-9999)#
DescriptionOnce a caller has dialed in on the DISA trunk and accessed intercom dial
tone, he/she can access a trunk line by dialing 
#7, then the ID code set in this
address (9999 by default), then 9 or 81-86 to access the 
MC0 trunk.
Programming
To set DISA Outbound Call ID Code 2 . . .
FFl 6# 2# (OOOO-9999)#
t
4-Digit DISA Outbound ID Code 2
(Default:...

Section 400~ProgrammingChapter I. System Programming (FFl)ID Code For System Programming
Software Version: Ail VersionsAddress: 
FFl 7# (0000-9999)#
DescriptionThis program assigns an ID code that can be dialed from a non-Attendant
phone to enter the programming mode (9999 by default).
Non-Attendant extensions enter the programming mode by dialing 
#98 and
then the ID Code entered in this address.
Programming
To assign the ID Code for system programming . . .
FFI 7# (OOOO-9999)#
f
4-Digit ID Code for...

Chapter 1. System Programming (FFl)Section 400-Programming
New Function Reset
New Function Reset
Software Version:CPC-B Only, Version 4.0 or higher
Address:FFI 8# 1# (0 or l)# (to select the reset)
FFI 8# 2# (0 or l)# (to complete the reset)
DescriptionPerform this address if you are upgrading CPC-B software to a new release
(such as from 5.0 to 6.0). However, it is not necessary if you are upgrading to
a “point” release (such as 6.0 to 6.1). New Function Reset should be
performed immediately after...

Section 400-ProgrammingChapter 1. System Programming (FFl)
DID/DNIS and Tl Settings
Inbound DID Dial Numbers
Software Version:CPC-B Version 3.1 or higherAddress: 
FFl 6# 3## (OOOO-9999)## (IO-69 or lOO-699)#
DescriptionUse this address to assign DID number(s) to extension(s).
Up to 500 DID numbers can be assigned.
One DID number can be assigned to multiple extensions (this will take up
only one entry in the 500 available entries).
One extension can have multiple DID numbers assigned to it. (The
number of...

DID Hardware and Power Requirements.The DID trunk card is required
(each DID card provides 8 ports). The DID trunk card requires an external,
-48V power supply. Also, SCC-B Card Version 1.2 or higher is required. See
Section 300~Installation for cabling instructions.
Dial Pulse Requirement.Ti:e DID trunk card requires dial-pulse dialing.
Digit Length Requirement.The DBS only supports 4-digit DID numbers.
DID Ring Control.Ringing for the DID number at the assigned extension(s)
is controlled by the DID...

Section 400-ProgrammingChapter 1. System Programming (FFI)
System ConfigurationSoftware Version:CPC-B Version 4.0 or higher
Address: 
FFl 8# 4## l# 1# (0-8)#
DescriptionUse this address to identify the DBS system configuration in which the Tl
interface is installed (DBS 40 by default).
This is 
one of the required addresses to make Tl operational. See
YHinimum Tl Programming” below for more information.
Programming
System Configuration
Default: 0 (DBS 40)
(see table below)
Table l-35. System ConfQzuatitm...