Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. system rrogrammlng (I-Fl)Section 400-ProgrammingDoor Opener Access Code
Software Version:
CPC-Ail and CPC-B, Version 7.0 or higher
Address: 
FFl 2# 9# (DoorPhone)# 3# (OOOO-9999)#
DescriptionUse this address to establish a 4-digit door opener access code that can be
entered on any extension phone to unlock the door. This applies to door
phones connected to digital extension ports only (not trunk ports).
NOTE:To require the use of the access code to unlock the door, address
FF12# l# 40# must be...

---..-.. .-- -~ .-........,v.,y .“. . . -,-.-... ..-=.- . . . . . . . . ..
Door Phone Tone Type
Software Version:CPC-All and CPC-B, Version 7.0 or higherAddress: 
FFl 2# 9# (DoorPhone)# M (0 or l)#
DescriptionThis address specifies the type of tone heard by the cal,led extension when a
visitor presses the door phone button. This appiies to door phones connected
to digital extension ports only (not trunk ports).
Prdgramming
1
FFI 2# 9# (I-4)# 4# (0 or I)#
f
4
I
Door Phone Number
(l-4)
Tone Type: (heard by...

Chapter 1. System Programming (FFl)Section 400-ProgrammingDoor Phone Ring Timeout Timer
Software Version:CPChl and CPC-6, Version 7.0 or higherAddress: 
FFl 2# 9# (DoorPhone)# 5# (O-15)#
DescriptionThis address sets the amount of time (in seconds) that a door phone will ring
an extension before it goes on-hook (extension stops ringing). This applies to
door phones connected to digital extension ports only (not trunk ports).
If the door phone caller re-initiates the call before this Timer is up, the...

Section 400-ProgrammingChapter 1. System Programming (FFI)
Door Phone Ring Pattern
Software Version:CPC-AlI and CPC-8, Version 7.0 or higherAddress: 
FFl 2# 9# (DoorPhone)# 6# (O-5)#
DescriptionThis address specifies the ring pattern heard at the extension receiving a door
phone call. This applies to door phones connected to digital extension ports
only (not trunk ports).
This address specifies the number of seconds between rings (4 seconds by
’default). The ring itself has a fixed duration of...

Door Opener Relay Timer
Sofhnfare V&ion:CPC-Alland CPC-B, Version 7.0 or higherAddress: 
FFl 2# 9# (DoorPhone)# 7# (*5)#
DescriptionUse this address to determine the number of seconds a “buzzing” (unlocked)
door will remain unlocked for the visitor to enter the building (4 seconds by
default). This applies to door phones connected to digital extension ports
only (not trunk ports).
This Relay Timer begins immediately after an extension enters the
appropriate codes (#3*, #3 NNNN *, #3 XXX *, or #3 Xxx NNNN...

Section 400~ProgrammingChapter 1. System Programming (FFi j
System Timers
Automatic Night Mode Start Time
Software Version: All VersionsAddress: 
FFl 3# 1# (OOOO-2359)#
DescriptionSet the time when the DBS will automatically switch from Day to Night
mode. Use the 24-hour military time format (e.g.. enter 
“1700” for 5:00 pmj.
You can program trunks to ring incoming calls at different extensions when
the system is in Night mode (see FF4 addresses). And different TRS types
can be programmed to be used...

bnaprer I. 3ystw11 rrogrammlrly (rr I 13ec11on 4uu-rrogrammlng
NIGHT Key Operation.If only one of the Auto Mode Start Times is set, the
Attendant 
NIGHT key can be used to manually switch to another mode. For
instance, if Night mode has been activated automatically, the Attendant can
press the 
NIGHT key to go into Day mode. (However, the Attendant must
wait at least 3 minutes after the mode is automatically activated, before using
the 
NIGHT key to switch the mode again.)
In 
CPC-AU/B versions prior to...

Section 400-ProgrammingChapter 1. System Programming (FFl)Attendant Hold Recall Timer for CO Calls
Software Version: All VersionsAddress: 
FFl 3# 2# (O-12)#
DescriptionThis timer determines how long a trunk call can be held by an Attendant
phone before it will recall (20 seconds by default).
Programming
I
FFl 3# 2# (0112)#
t
Attendant Hold Recall Timer setting for CO calls
Default: 1 (20 seconds) (see table below)
Table l-8.Attendant Hold Recall Timer values for CO calls
7.SettingValue
0No recalli 20...

Chapter I. System Programming (FFi)Section 400-Programming
Extension Hold Recall Timer for CO CallsSoftware Version: 
All Versions
Address: 
FFl W 3#! (O-12)#
DescriptionThis timer determines how long a trunk call remains on hold at an extension
before it recalls (starts ringing the extension again; 140 seconds by default).
Programming
FFl 3# 3# (092)#
Extension Hold Recall Timer setting for CO calls
Default: 7 (140 
seconds) (see table below)
Table l-9.Extension Hold Recall Timer values for CO calls...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Attendant Transfer Recall Timer for CO Calls
Sofhrvare Version: All VersionsAddress: 
FFl 3## 4# (0112)#
DescriptionWhen an Attendant phone transfers a trunk call to an extension or hunt group,
the transferred call will recall to the Attendant if it is not answered. This
timer determines how long a transferred trunk call will go unanswered before
it recalls (20 seconds by default).
Programming
I1
FFl 3# 4# (0112)#
t
Attendant Transfer Recall...