Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. System Programming (FF1)Section 400-Programming
External (UNA) Relay Control
Ring Patterns For UNA Terminals (M, C and B)
Software Version: All VersionsAddress: 
FFl 2# 4# l# (0 or l)#
DescriptionUse this address to set the ring pattern for incoming trunk calls sent to
Universal Night Answer (UNA), where calls ring over a loudspeaker or
amplifier. By default, the ring pattern is 1 second on 
/ 3 seconds off.
This address controls the UNA relay terminals labeled “M”, “C” and “B” on
the DBS...

Section 400-FrogrammingChapter 1. System Programming (FIT j
External Page Interface Control For Paging Groups
Software Version: All VersionsAddress: 
FFl 2# 4## (219)# (0 or l)#
DescriptionUse this address to activate external paging (e.g., loudspeaker installed in
ceiling) for paging groups 
00-04. Paging groups 05-07, although included in
this address, cannot be activated for external paging.
Internal paging, where a page is announced on the speakers of extension
phones belonging to the page group...

Chapter 1. System Programming (FFl)Section 400-Programming
Class of ServiceExtension Class Of Service
Software Version:CPC-All (all versions); CPC-B Version 3.1 or higherAddress: 
FFl 2# 5# (1-8)# (l-21)# (0 or l)#
DescriptionThis address allows you to define up to 8 different Classes of Service, by
enabling or disabling the phone features of each. Up to 21 features are
available (see table below). The definable Classes of Service are numbered
1-8. An additional Class of Service “0” automatically enables...

Section 400~ProgrammingChapter 1. System Programming (FFl)
12Direct Pickup (79)
13Group Pickup (70)
14Tone/Voice Mode (1)
15Message Waiting Set (2)
16Busy Override (4)
17call waiting (3)
18Offhook Voice Announce (5)
I191 Central Office Call Queuing (2)I
forwarding for internal calls in CPC-B
Related Programming
Extension Class of Service Assignment: FF3 (ExtPort)# 3%
NotesInteraction with Extension Class of Service Assignment.By default, every
extension is assigned to Class of Service “0” (all 21...

Chapter 1. System Programming (F F1)Section 400-Programming
Account Codes
Verified Forced Account Codes
Software Version:CPC-All (all versions); CPC-8 Version 3.1 or higherAddress: 
FFl 2# 6# (10lOO)# l# (OOOl-9999)#
DescriptionUse this address to assign up to 100 four-digit verified account codes. Once
the account codes are assigned, use address 
FE1 2# 6# (l-lOO)# 2# (0-7)# to
assign a Toll Restriction Setting (TRS) value to the account code.
Forcing the use of account codes, as well as system...

Section 400~Programming
Chapter 1. System Programming (FFl)
Assigning 9999 as Account Code 100 . . .
To assign “9999” as Account Code 100, enter this address:
FFl 2# 6#! low l# 9999#
Related Programming
Toll Restriction For Verified Forced Account Codes: FFl 2# 6# (l- 1 OO)##
2# (O-7)#Forced Account Codes: 
FF3 (ExtPort)# 5# (0 or l)#
Toll Resttiction Settings: FF7 addresses
NotesForced Unverij’ied Account Codes.With CPC-AII and CPC-B versions
prior to 6.0, Unverified Account Codes can only be used on a...

Chapter 1. System Programming (FFl)Section 400-Programming
Toll Restriction For Verified Forced Account Codes
Software Version:CPC-All (all versions); CPC-B Version 3.1 or higherAddress: 
FFl 2# 6# (l-lOO)# 2# (017)#
DescriptionUse this address to assign toll restriction (TRS) types to Verified Forced
Account Codes. A caller who enters the account code will be restricted by the
TRS 
type assigned to the acccurzt code (not the TRS type assigned to the
exterdion).
Programming
1
FFl 2# 6# (1.f)O)# 2#‘,$...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Flexible Function Screens
Flexible Function Screen Soft-Key Assignment
Software Version:CPC-All and CPC-B, Version 6.0 or higherAddress: 
FFl 2# 7# l# (Screen)# (SoftKey)# (Feature)#
DescriptionUse this program to create up to 15 menu screens for large-display phones.
Each screen can contain up to 10 feature codes (one feature code per soft
key). “Soft keys” are the 10 buttons located on the left and right sides of the
LCD display window on the...

Chapter 1. System Programminq (FFI)Section 400-Programming
Programming
FFl 2# 7# l# (2539)# (l-lO)# (xxxxxx)#
t
Screen Number: ’
25=Flex.Func. Screen 1
26=Flex.Func. Screen 2
27=Flex.Func. Screen 3
28=Flex.Func. Screen 4
29=Flex.Func. Screen 5
30=Flex.Func. Screen 6
3 l=Flex.Func. Screen 7
32=Flex.Func. Screen 8
33=Flex.Func. Screen 9
34=Flex.Func. Screen 10
35=Flex.Func. Screen ! 1
36=Flex.Func. Screen 12
37=Flex.Func. Screen 13
38=Flex.Func. Screen 14
39=Flex.Func. Screen 15
Soft Key NumberFeature...

Section 400-Programming
Chapter 1. System Programming (FFl)
Code to be assigned to soft key
Feature
(FFll enters an asterisk *)
(FF12 enters a pound sign #)
Call Forward72Note: Beginning with CPC-AIL/B Version
Call Forward--All Calls7207.0, you can call-forward to an outside
Call Forward--Busy/No Answer
721phone number. Use an existing PSD or SSD
Call Forward--Busy
722code as the destination phone number, with aCall Forward--No Answer
724“CX-PhoneNo.” format (where C is the
CONF key, and X is l-6 or 9...