Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. System Programming (FFI)Section 400-ProgrammingAttendant LED Alarm Indication
Software Version:CPC-B Versions 2.09 to 4.0 (requires Attendant Feature Package)Address: 
FFl 2# l# 29# (0 or l)#
DescriptionUse this address to allow or disallow the Alarm feature (LED lights to
indicate an alarm condition) to be assigned to an FF key on an Attendant
phone. By default, the Alarm feature can be assigned.
NOTE: The Attendant Feature Package (AFP) was discontinued in CPC-B
Version 5.0.
Programming
I...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Extension (BLF) Delayed Ring
Software Version:CPC-All (all versions) and CPC-6 Version 2.0 or higherAddress: 
FFI 2# l# 30# (0 or l)#
DescriptionUse this address to enable or disable Delayed Ringing for intercom calls. By
default, Extension 
(BLF) Delayed Ringing is disabled.
Delayed Ringing is a call-forwarding feature for unanswered calls -- if an
incoming call is not answered at one extension, the system will send the call
to another...

Chapter 1. System Programming (FFl)Section 400-Programming
Analog Transfer Ring Pattern
Software Version:CPC-All (all versions) and CPC-B Version 2.11 or higher
Address:
FFl 2# 1# 31# (016)#
DescriptionUse this address to choose a distinctive ringing pattern for calls transferred to
analog SLT phones. This setting is typically used for calls transferred to a
modem, or for SLT phones requiring distinctive ringing for transferred calls,
There are 7 different patterns (numbered 
O-6) to choose from. The...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Multiple DID/DNISSoftware Version:
CPC-B Version 4.0 or higherAddress: 
FFl 2# l# 32# (0 or l)#
DescriptionUse this address to enable or disable Multiple DID for analog trunks, or
Multiple DID and DNIS for 
Tl trunks. By default. Multiple DID/DNIS is
disabled.
With Multiple DID/DNIS enabled, one DID or DNIS number can be assigned
to multiple extensions, which will simultaneously ring when an outside caller
dials the DID or DNIS number.
lDID...

Chapter 1. System Programming (FFl)Section 400-Programming
NotesRestrictiun Far CPC-B Version 3.1.
This address is also present in CPC-B
Version 3.1; however, it only controls Multiple DID (DMS cannot be used
with this version).
DID Hardware and Power Requirements.The DID trunk card is required:
each card provides 8 ports. The card requires dial-pulse dialing and an
external, 
-48V power supply. See Section 300-Installation for cabling
instructions.
DZDIDNZS Digit Length Requirement.The DBS only supports...

Section 400~ProgrammingChapter 1. System Programming (FFI)
Page Duration
Software Version:CPC-All (all versions) and CPC-B Version 3.1 or higher
Address:FFI 2# l# 33# (0 or l)#
DescriptionThis address determines whether the DBS system will automatically close the
paging circuit 60 seconds after a page is initiated. By default, the paging
circuit is left open indefinitely, until the paging person closes the circuit by
hanging up.
Programming
O=The page circuit remains open indefinitely.
l=The paging...

Chapter 1. System Programming (ITI)Section 400-Programming
SLT DISA Ring Pattern
Software Version:CPC-All (all versions) and CPC-B Version 3.1 or higher
Address:FFl 2# l# 34# (0 or l)#
DescriptionUse this address to specify a distinctive ring pattern for DISA calls on SLT
phones, or follow the Analog Transfer Ring Pattern setting. By default, the
pattern is 1 second on 
/ 3 seconds off.
Programming
FFl 2# 1# 34# (0 or l)#
1
kl second on / 3 seconds off.
i=Same as the Analog Transfer Ring Pattern.
Related...

3wau11 4uu-rluylatitiwlgb11dp3 I. 3yaica11 riuyiaii!~iiiiiy [t-r I;
AEC Disconnect Signal Duration
Software Version:CPC-All (all versions) and CPC-B Version 5.0 or higher
Address:FFl 2# 1# 35# (0-15)#
DescriptionUse this address to set the duration of a positive disconnect signal sent from
analog extension ports (VB-43621A version of the AEC card). Sending this
signal allows quick disconnect from third-party voice mail systems. By
default, no disconnect signal is sent.
This address applies to CPC-AI1 and...

Chapter 1. System Programming (FFl)Section 400-Programming
DIDlDNlS to a Voice Mailbox
Software Version:CPC-8 Version 6.0 or higherAddress: 
FFl 2# l# 36# (O! 1 or 2)#
DescriptionThis address determines whether (and how many) final digits of a DlD/DNTS
phone number are transmitted to Voice Mail, in cases where the DID/DMS
trunk is assigned to ring directly to Voice Mail (not to a DBS extension
phone). This address allows 
DWDNIS calls to be routed to a Voice Mailbox
system that is not connected to a...

Third-Party Voice Mail.This feature can be used with Panasonic’s Voice
Mail system or with third-party Voice Mail systems. If the feature is used
with third-party Voice Mail systems, the Voice Mail can be connected through
analog extension ports or OPX ports.
Call Forward ID Code for DIDfDNIS Calls To An Extension.If a DIDI
DNIS call is assigned to ring an extension, and the extension is programmed
to forward to Voice Mail, only the Call Forward ID Code will be transmitted
to Voice Mail (the 
DID/DNIS...