Panasonic Cpc+AII/B Digital Business System Release Notes Manual

DID/DNIS Answer Code
Software Version:CPC-6 Version 6.0 or higherAddress: 
FFl 2# l# 37# (Code)#
DescriptionUse this address to specify a DID/DNIS Answer Code. The Answer Code is
used for routing 
DID/DNIS calls to a Voice Mailbox system that is not
connected to a physical extension.
To implement this feature, assign 
DID/DNIS trunks to ring directly to the
Voice Mail system using FF4 ring assignment addresses. Once Voice Mail
answers, the DBS sends the 
DID/DNIS Answer Code, which signals the
Voice Mail...

Voice Mail Ports and Hunt Groups.The DIDIDNIS digits can be sent to a
specific Voice Mail porr or a Voice Mail hunt group.
Second Hunt Group.If the DID/DNIS call rings into a hum group that is
programmed to transfer calls to a second hunt group, the 
DID/DNTS call will
not be transferred to 
the second hunt group.
Third-Party Voice Mail.This feature can be used with Panasonic’s Voice
Mail system or with third-party Voice Mail systems. If the feature is used
with third-party Voice Mail systems, the Voice...

Chapter 1. System PrOgrammIng (Wl )Sectlon 400~Programming
LCD Timer for Caller ID
Software Version:CPC-All and CPC-B, Version 6.1 or higher
Address:
FFl 2# l# 38# (0,l or 2)#
DescriptionThe LCD Timer determines how long the DBS waits before displaying call
duration timing on the phone’s LCD. This Timer allows Caller ID
information (if available) to appear before the call duration timing is
displayed.
For example, if the LCD Timer is set to 5 seconds (default), call duration
timing will start displaying...

Internal Hold ToneSoftware Version:CPC-All and CPC-B, Version 7.0 or higher
Address:FF1 2# l# 39# (0 or l)#
DescriptionUse this address to enable or disable Internal Hold Tone, which is a double-
beep heard every 7 seconds by a caller on hold.
Programming
FFl 2# l# 39# (0 or I)#
&Disabled (no Internal Hold Tone)
l=Enabled (Internal Hold Tone heard)
NotesMOH Override.Internal Hold Tone (if enabled) will override any MOH
(Music-On-Hold) sound source installed.
DBS-70-400DBS Manual - Issued 8/l/95Page l-49
\ 

Lnapter 1. System Programmtng (FFl)Section 400-Programming
Door Opener Access Code Required
Software Version:CPC-All and CPC-8, Version 7.0 or higher
Address: 
FFl 2# l# 40# (0 or l)#
DescriptionThis address determines whether a Door Opener Access Code must be
entered on an extension to unlock the Door Box. This applies to Door Boxes
connected to digital extension ports (not trunk ports).
Programming
I
FFl 2# l# 40# (0 or l)#
t
O=Not required
1 =Required
Related ProgrammingDoor Phone Extensions: 
FFl 2#...

Section 400-ProgrammingChapter 1. System Programming (FFl j
API Port Type
Software Version:CPC-All and CPC-8, Version 7.0 or higherAddress: 
FFl 2# 1# (41 or 42)# l# (0 or l)#
DescriptionUse this address to configure the appropriate API port for TSAPI protocol.
Only one API port should be configured for TSAPI.
Programming
FFI 2# 1# (41 or 42)# 1# (0 or l)#
+-r
API Port Number:Port Type:
41=API Port 1O=Standard API protocol
42=API Port 2l=TSAPI protocol
Related ProgrammingAPI Baud Rate: 
FFl 2# I# (41 or...

Chapter 1. system rrogrammlng (t t 1)section 400~Programming
API Baud Rate
Software Version:CPC-Ail and CPC-B, Version 7.0 or higher
Address:
FFl 2# 1# (41 or 42)# 2# (0 or l)#
DescriptionThe baud rate for the TSAPI port can be set to either 9600 or 19200 bps.
Programming
FFl 2# 1# (41 or 42)# 2# (0 qr l)#
API Port Number:
41=API Port 1
42=API Port 2
Baud Rate:
0=9600 bps
1=19200 bps
Related ProgrammingAPI Port Type: 
FFl 2# l# (41 or 42)# 1# (0 or l)#
NotesUsing Both API Ports.If both API ports are...

3eGu011 4uu-I- I uyl al I I I I Ill lyw~apiai I. ~y3~c111 rluyiaiiiiiwly it-r 11
Serial Port Parameters (TTY Settings)
Parity Check
Software Version: All VersionsAddress: 
FFl 2# 2# l# (0 or l)#
Dbscription
Programming
.
This address determines whether the DBS checks parity over serial port CN6.
By default, parity checking is turned on.
If parity checking is activated, select the parity count -- “Even” or “Odd” -- in
FF12# 2# 2#.
Serial Port CN6 is normally used for SMDR.
FFl 2# 2# 1# (0 qr l)#
O=Turns...

Gnapter 1. system rrogrammtng p-1 )sectron 400~Programming
Odd/Even Parity
Software Version: All Versions
Address:
FFl 2# 2# 2# (0 or l)#
DescriptionIf parity checking for Serial Port CN6 was activated in FF12# 2# l#, this
address (Odd/Even Parity) determines whether the check is based on an even
count or an odd count. By default, the parity count is even.Programming 
-
FFl 2# 2# 2# (0 or l)#
t
O=Odd parity.
l=E ven parity.
NotesChecking Communications Parameters.If you later change this address
value,...

Baud RateSoftware Version: All Versions
Address:
FFl 2# 2# 3# (114)#
DescriptionUse this address to set data transmission speed (baud rate) between Serial
Port CN6 and the peripheral equipment attached to it. By default, baud rate is
set at 9600 bits per second.
Programming
I
IFFl 2# 2# 3# (3;4)#
1=300 bps
2=1200 bps
3-4800 bps
4=9600 bps
NotesChecking Communications Parameters.If you later change this address
value, be sure to check all Serial Port addresses -- 
FFl 2# 2# I# thru 9# -- to
make sure they...