Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Chapter 1. System Programming (FF1)Section 400-Programming
Voice Mail Busy Tone
Software Version: All-VersionsAddress: 
FFl 2# 1# 21# (0 or l)#
DescriptionThis address determines what is sent to a voice-mail uort at the conclusion ofL
a call -- either silence or a busy tone. By default, the DBS sends silence.
Programming
I
FFl 2# l# 21# (0 or l)#
O=Silence.
1 =B usy tone.
Related Programming
API/AEC Slot Assignment: FF1 2# l# 20# (2-18)#
Page l-26DBS Manual - Issued 8/l/95DBS-70-400 . 

Section 400-Programming
Chapter 1. System Programming (FFl)
Analog Transfer Ring Pattern
Software Version:CPC-A Only (Version 3.21 or higher)Address: 
FFl 2# l# 22# (O-6)#
DescriptionThis address determines which ringing pattern is used for transferred calls to
devices connected to analog extension ports. By default, the ringing pattern
is 
.4 seconds on 13.6 seconds off.
This setting is typically used to assign specific ringing patterns for calls
transferred to a modem, or for 
SLTs that require...

Chapter 1. System Programming (FFl)Section 400-Programming
Attendant Overflow for Primary Attendant
Software Version:CPC-B Version 1 .O onlyAddress: 
FFl 2# l# 22# (l-15)#
DescriptionThis address determines the maximum number of trunk calls that can be
stacked at the Primary Attendant phone. By default, up to 8 calls can be
stacked at a time.
Calls exceeding the set limit are automatically transferred to other extensions.
To determine which extensions receive ovefflow trunk calls, use the Day and
Night...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Delayed Ring
Software Version:CPC-All (all versions) and CPC-B Version 2.0 or higher
Address:FFl 2# l# 23# (0 or l)#
DescriptionThis address determines if delayed ringing is allowed for CO trunks. By
default, delayed ringing is disabled.
Delayed ringing is an automatic transfer of unanswered calls -- if an incoming
call is not answered at one extension, the system will send the call to another
extension (the first extension will cease ringing)....

Chapter I. System Programming (FFI)Section 400-Programming
AEC Disconnect Signal Duration
Software Version:CPC-A Version 3.3 or higherAddress: 
FFl 2# l# 23# (0115)#
DescriptionUse this address to set the AEC card (VB-43621A) to provide a positive
disconnect signal, and determine the duration of the signal. By default, the
disconnect signal is not sent.
If set, analog extension ports will provide a disconnect signal (open loop)
upon hangup. Sending this signal allows quick disconnect from third-party...

Section 400-Programming
Chapter 1. System Programming (FFl)Second Attendant Position
Software Version:CPC-All (all versions) and CPC-B Version 2.0 or higher
Address:FFI 2# I# 24# (11-69 or 10%699)#Description
This address assigns an extension number as the Second Attendant position.
By default, the Second Attendant position is extension 101.
When all line appearances at the Primary Attendant are busy, calls will
transfer in sequence to the Second. Third, and Fourth Attendants. If all line
appearances are...

Chapter 1. System Programming (FFl)Section 400-Programming
Third Attendant Position
Sofhuare Version:CPC-Ail (all versions) and CPC-8 Version 2.0 or higher
Address:FFl 2# l# 25# (11-69 or 101-699)#
DescriptionThis address assigns an extension number as the Third Attendant position.
By default, no extension is assigned as the Third Attendant.
When all line appearances at the Primary Attendant are busy, calls will
transfer in sequence to the Second, Third, and Fourth attendants. If all line
appearances are...

Section 400-ProgrammingChapter 1. System Programming (FFl)
Fourth Attendant Position
Software Version:CPC-All (all versions) and CPC-B Version 2.0 or higher
Address:FFl 2# 1# 26# (11-69 or 10%699)#
DescriptionThis address assigns an extension number as the Fourth Attendant position.
By default, no extension is assigned as the Fourth Attendant.
When all line appearances at the Primary Attendant are busy, calls will
transfer in sequence to the Second, Third, and Fourth Attendants. If 
all line
appearances...

Chapter 1. System Programming (FFI)Section 400-Programming
Attendant Transfer Extension
Sofhnrare Version:CPC-All (all versions) and CPC-B Version 2.09 or higher
Address:FFl 2# 1# 27# (11-69 or lOl-699)#
DescriptionIf all line appearances are busy on all Attendants (Primary, Second, Third and
Fourth), calls will transfer to the extension assigned in this address.
Programming
To assign an Attendant Transfer Extension . . .
FFl 2# l# 27# (11-69 or 10%699)#
t
Extension Number
(default: 
no Transfer...

Section 400-ProgrammingChapter 1. System Programming (FFi jAttendant Override
Software Version:CPC-Ail (all versions) and CPC-B Version 2.09 or higher
Address:FFl 2# l# 28# (0 or l)#
DescriptionUse this address to enable or disable the Attendant Override feature. which
allows an Attendant phone to “barge into” a trunk or intercom call in progress
on any extension -- even if the extension has been programmed to block
barge-ins. By default, Attendant Override is enabled.
When a barge-in occurs, all three...