Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Table of ContentsSection 400-ProgrammingList of Tables
TableI.DBS programstructure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intro-6
Table 2. Default program settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intro-9
TableI-l.
SLT HookflashControl...

secrlon 4uwrrogrammlngI ama OT c;ontenrs
TableI-39.Release Acknowledge Timer values.................................................................I-148
Tablel-40.Outpulse Delay Timer values...........................................................................l-149
Tablel-41.Wink Timeout Timervalues...........................;..................................................I-150
TableI-42.IncomingDetectionTimer values....................................................................I-151...

Table8-1.TimePriority RouteTable format..........................................................................8-3
Table8-2.TimePriorityRouteTable format........................................................................8-10
Table8-3.LCRtable.........................................................................;.....................................8-5
Table 8-4. LCR time periods and positions used...................................................................S-11
Table 8-5. LCR trunk...

,About This Section
This Section 400 is intended for use as a technical reference manual for DBS programming via the
FF keys on 
a DBS key phone. (Other programming methods are described in Appendix B of this
section.)
StructureSection 400 is structured according to FF key numbering. For example,
Chapter 1 covers 
FFl programs; Chapter 2 covers FF2 programs; and so on.
The FF keys categorize the programs by subject -- each FF key represents a
group of related programs as follows:
Chapter 1
Chapter 2...

Introduction to DBS ProgrammingThis introduction provides an overview of DBS programming from a phone.
For descriptions of other DBS programming methods. see Appendix B of this
manual.The following table summarizes the topics contained in this introduction.
TopicPage
Before You BeginIntro-3Preparations for Programming
IllUO-3Initializing DBS Systems 
(RAMCLR)Intro-4
Upgrading CPC-B Software (New Function 
Reset)Intro-5Understanding FF Key Programming
Intro-6Program Structure
Intro-6How to Enter the...

Intro-2DBS Manual - Issued 8/l/95DBS-70400 

Section 400~ProgrammingIntroduction to DES Programming
Before You Begin
This section describes preparations that should be completed before you start
programming. 
If you are familiar with FF key programming for DBS
systems, you may begin programming as soon as these preparations have
been made.
If you are new to DBS programming, be sure to read “Understanding FF
Key Programming” 
on page Intro-5 before you begin.
Preparations for Programming
Prior to programming the DBS system, make sure you have...

Initializing DBS Systems (RAMCLR)
After installing a new DBS system, or when upgrading to Version 7.0, you
must initialize the CPC (Central Processing Card) before programming the
system.
IMPORTANT:This procedure must be performed before you program
the DBS system. Failure to initialize the CPC before programming may
cause operational problems.Figure 1.
The procedure described below re-initializes the entire DBS memory, and
resets all programs to their default values. This means that all programs used,...

Section 400-ProgrammingIntroduction to DBS Programming
Upgrading CPC-B Software (New Function Reset)
Perform the following procedure when upgrading CPC-B software to a new
version. 
Exception: If upgrading to Version 7.0, the system must be
initialized instead: see 
“‘Initializing DBS Systems (RAMCLR)“. previous
page.
IMPORTANT:Perform New Function Reset if upgrading to a new
release -- from 5.0 to 6.0, for example. It is not necessary for a “point”
release (e.g., from 5.0 to 5.2).
New Function Reset...

Introduction to DBS Programming
Section 400-Programming
Understanding FF Key ProgrammingProgram Structure
Program entries for the DBS are organized into 10 primary groups, which are
listed in Table 1 below. Each group has its own Flexible Function (FF) key
on the phone. These keys can be identified by the LED on the left side of the
key. On key telephones, the FF keys are numbered left-to-right, starting on
the bottom row.
After you enter the programming mode (see “How to Enter the
Programming Mode”,...