Panasonic Cpc+AII/B Digital Business System Release Notes Manual

secnon 400~ProgrammingGnapter 3. txtenslon Programming (FF3)
Auto Set Relocation Code
Software Version:CPC-All (all versions); CPC-B Version 3.1 or higherAddress: FF3 
(ExtPort)# 41# (OOOl-9999)#
DescriptionYou can relocate (or swap) the program settings of one phone to another. The
Auto Set Relocation Code enables you to perform the relocation.
For example, if the phone from ext.102 is unplugged and moved to an office
with a wall jack (port) that is assigned to ext.103, this feature can be used to...

wapter 3. txtenslon rrogrammlng (w3)bectlon 400~Programming
6.To return extension 103 to service, disconnect then reconnect the
extension cable. When extension 103 is retuned to service, it 
will
have the program settings of extension 
102.
Restrictior~.
Phone settings cannot be exchanged between digital and
analog 
(SLT) ports.
Page 3-50
DBS Manual - Issued 8/l/95DBS-70-400 

Permanent Call Forward Type
Software Version:CPC-All (all versions)j CPC-8 Version 3.1 or higherAddress: FF3 
(ExtPort)# 42# (0-3)#
DescriptionUse this address to enable an extension for Permanent Call Forwarding, so
that calls to that extension (if the extension is busy and/or not answered) will
be forwarded to another location. This feature is often used for sending calls
to Voice Mail, or forwarding peripheral equipment to a single extension port.
ProgrammingFF3 
(I-144)# 42# (093)# 
t
Extension...

~~L~IUI I rcuu-r I uyl a I II I III iyPermanent Call Forward Extension
Software Version:CPC-All (all versions); CPC-B Version 3.1 or higherAddress: FF3 
(ExtPort)# 43# (IO-69 or lOO=699)#
DescriptionIf an extension is enabled for Permanent Call Forwarding (in address FF3
ExtPort# 41#), use this address to set another extension number as the target
or “permanent call forwarding point” for the forwarded calls.
In addition to regular extension numbers, the permanent call forwarding point
can also be a...

wcnon 4uwrruyrammlngbriaprer 3. txrerlslori rrogramrrimg [t-w)
ML/MC0 Separation
Software Version:CPC-All (all versions); CPC-8 Version 4.0 or higherAddress: FF3 
(ExtPort)# 44## (0 or l)#
DescriptionUse this address to enabie an extension for MC0 or ML key usage.
The difference between ML (Multi-Line) and 
MC0 (Multi-Central Office)
has to do with incoming calls. 
MC0 means multiple trunks can be received at
the extension -- if you press a flashing FF key, you will get an incoming trunk
.call. Calls...

VAU Hunting PrioritySoftware Version:CPC-All (all versions); CPC-B Version 5.0 or higherAddress: FF3 (ExtPort)# 
45# (0 or l)#
DescriptionUse this address to assign hunting priority to calls that ovefflow from a hunt
group to the VAU.
If hunting priority is assigned, a caller who hears the VAU message and then
decides to dial back into the hunt group, will be placed before other calls that
have just entered the hunt group queue.
Without hunting priority, the caller loses his or her place in the queue and...

Section 400-ProgrammingChapter 3. Extension Programming (FF3)
AEC Disconnect
Software Version:CPC-All (all versions); CPC-6 Version 5.0 or higherAddress: FF3 (ExtPort)# 
46# (0 or I)#
DescriptionThe VB-43621A version of the AEC card can be set to provide a positive
disconnect signal. Use this address to enable or disable the AEC disconnect
signal on individual extension(s).
If this option is enabled, analog extension ports will send a disconnect signal
(open loop) upon hangup. Sending this 
signal allows...

Chapter 3. Extension Programming (FF3)Section 400-Programming
VAU Port Assignment
Software Version:CPC-All (ail versions); CPC-B Version 5.0 or higher
bddress: FF3 (ExtPort)# 47# (0 or I)#
I’
DescriptionThis program assigns a digital port as a VAU (Voice Announce Unit).Once a
port is assigned as a VAU, the system treats that port as ifthe following
changes have been made:
l Offhook Signal (CO) is disabled - FF3 (ExtPort)# 7# O#.l Call 
Waiting/OHVA is disabled -- FF3 (ExtPort)# 8# O#.l Auto Pickup is...

Section 400-ProgrammingChapter 3. Extension Programming (FF3)
Hot Dial Pad
Software Version:CPC-All and CPC-B, Version 7.0 or higher
Address:FF3 (ExtPort)# 48# (0 or I)#
DescriptionThe dial pad on digital key phones can be designated as “hot” on an
extension-by-extension basis. This feature allows the user to initiate a call
without going 
ofIhook, by pressing any of the numeric keys O-9 (the “*” and
“#I” keys are not “hot”).
The extension’s dial pad can be “hot” under these conditions:
lwhen the...

t .Chapter 3. Extension Programming (FF3)Section 400-Programming
Auto-Redial on Extensions
Software Version:CPC-All and CPC-6, Version 7.0 or higherAddress: FF3 
(ExtPort)# 49# (0 or I)#
DescriptionUse this address to enable or disable the Auto-Redial feature on individual
DBS extensions (DSLT or K-Tel only).Auto-Redial allows a telephone in the
on-hook (idle) state to redial an 
internaI extension or an outgoing trunk call
without going off-hook first. By default, Auto-Redial is enabled on all DSLT
and...