Oce TCS400 User Manual

							251
Océ TCS400
User manual
Chapter 15 
Océ Power Logic® controller: Océ 
Remote Logic®
Downloaded From ManualsPrinter.com Manuals 
						

							252 Océ TCS400 User manual
Introduction to Océ Remote Logic®
The applications of Océ Remote Logic®
You must use Océ Remote Logic® to connect to the Océ Power Logic® 
controller applications if you do not have a keyboard, mouse and monitor with 
your Océ Power Logic
® controller.
You can use Océ Remote Logic
® to run the following applications from a 
remote workstation:
■Océ Settings Editor
Use the application to change the default settings of the system.
■Océ Queue Manager
Use the application to manage the print jobs.
■Océ System Control Panel
Use the application to view the status of the printer, the scanner and the 
controller. You can also view the media available on the printer and the 
amount of set memory in use.
User modes
The Océ Remote Logic® controller applications have different user modes (see 
‘The Océ TCS400 users’ on page13). An additional user mode is the Service 
operator mode. This mode is for the Océ technician only.
Downloaded From ManualsPrinter.com Manuals 
						

							Océ Power Logic® controller: Océ Remote Logic® 253
Install and start Océ Remote Logic®
Install Océ Remote Logic® on your system
Introduction
The Océ Remote Logic® application can run on all platforms with Java™ 
Virtual Machine. This section describes the installation procedures for the 
different types of platforms.
Before you begin
To install Océ Remote Logic® on Windows® 9.x, NT, ME, XP, or 2000, your 
system must be at least equipped with a Pentium® 233 with 32 Mb RAM.
Installation procedure for Microsoft® Windows® platforms
1
Insert the Océ Remote Logic® CD-ROM or the Océ Power Logic® controller 
CD-ROM into the CD-ROM drive of your PC.
2The installation starts automatically. If does not start automatically, run 
Setup.exe.
3Select the required language in the installation wizard and click OK.[74 ] Sel ect  the s etup l angu age
[74] Select the setup language
4Follow the instructions on the screen to complete the installation of Océ 
Remote Logic®.
Note:You can only use Océ Remote Logic® when TCP/IP is enabled on your 
system. Refer to your system administrator for help with the installation 
procedure for TCP/IP.
Downloaded From ManualsPrinter.com Manuals 
						

							254 Océ TCS400 User manual
Installation procedure for UNIX™ platforms
1
Check if a Java™ Runtime Environment (JRE) is installed on the system.
2From the directory Products/remotelogic/UNIX, unpack the contents of the 
file RemoteLogic_vX.tar to a subdirectory on the system.
3Use tar xvf RemoteLogic_vX.tar to unpack the file.
4Set the environment variable RL_VM_HOME to point to the installation of 
the JVM.
5Run the file remotelogic with the applications as parameters (for example 
remotelogic QM SCP SE to start the three applications), or use remotelogic 
AL as the application launcher.
UNIX™ versions and the required JRE
Note:
OS = Operating System, JRE = Java™ Runtime Environment
Where to download the Java™ Runtime Environments
[42 ] Download Java™ Runt ime E nvironmen ts
[42] Download Java™ Runtime Environments
UNIX™ version OS ver-
sionJRE Default installa-
tion directory
IBM
® AIX 4.1.5 1.1.6 /usr/jdk_base
IBM
® AIX 4.2.1 1.1.8 /usr/jdk_base
IBM
® AIX 4.3.3 + 
fix1.2.2 /usr/jdk_dev2
IBM
® AIX 4.3.3.10 
+ fix1.3.0 /usr/jdk_java130
SUN
® Solaris™ 2.6 1.1.6
HP-UX 10.20 1.1.3
LINUX
®1.0 1.1.3
LINUX
®1.2 1.1.8
Platform Preferred version Download location
1 1.1.8 http://www.ibm.com/java
2 C.01.18.xx http://www.unix.hp.com/ja-
va
3 N/A http://www.ibm.com/java
Downloaded From ManualsPrinter.com Manuals 
						

							Océ Power Logic® controller: Océ Remote Logic® 255
Installation procedure for other platforms
1
Install Java™ Virtual Machine (version 1.1.8).
2From the Océ Remote Logic® CD-ROM, load RemoteLogic_vX.tar or 
RemoteLogic_vX.zip.
3Set the environment variable RL_VM_HOME to point to the 
Java™Products/remotelogic/UNIX installation directory.
4If necessary, edit the Océ Remote Logic® script or batch file.
5Use the Océ Remote Logic® script or batch file to start the applications.
Downloaded From ManualsPrinter.com Manuals 
						

							256 Océ TCS400 User manual
Start the applications with Océ Remote Logic®
Introduction
Use the following two methods to start the applications with Océ Remote 
Logic®.
■Use the programs menu of your operating system.
■Use a command line parameter.
Use the programs menu to start the applications
1
Select Océ Remote Logic
2Select the Launcher application.
3Select the required application.
The application starts with your default system.
Note:You can select another system than your default system (see ‘Connect to 
the controller’ on page 260).
Downloaded From ManualsPrinter.com Manuals 
						

							Océ Power Logic® controller: Océ Remote Logic® 257
Use command line parameters to start the applications
Six command line parameters are available to facilitate the start of the 
applications.
■configfile=
Sets the configuration file to use.
■server=server
Sets the indicated server as the server to connect to.
■language1=lang
Specifies the first language in combination with the parameter 
country1=country.
■country1=country
Specifies the first language in combination with the parameter 
language1=language.
■language2=lang
Specifies the second language in combination with the parameter 
country2=country.
■country2=country
Specifies the second language in combination with the parameter 
language2=language.
Note:Always use a matching combination of language and country (see the 
following table).
Downloaded From ManualsPrinter.com Manuals 
						

							258 Océ TCS400 User manual
Parameters of supported languages
[43 ] Parameters  of s upport ed la nguag es
[43] Parameters of supported languages
Apply the parameters to the applications
Apply the parameters to the following applications:
■QM.exe (Océ Queue Manager)
■SCP.exe (Océ System Control Panel)
■SE.exe (Océ Settings Editor)
■AL.exe (Application launcher).
The easiest method for applying the parameters to the applications is to create 
a shortcut for an application. Then add the command line properties.Language Language parameters Country parameters
Danish da DK
Swedish sv SV
Norwegian no NO
Finnish fi FI
Hungarian hu HU
Czech cs CZ
Polish pl PO
German de DE
Dutch nl NL
UK English en GB
US English en US
French fr FR
Italian it IT
Spanish es ES
Portuguese pt PT
Chinese simplified cn CN
Chinese traditional cn TW
Japanese ja JP
Downloaded From ManualsPrinter.com Manuals 
						

							Océ Power Logic® controller: Océ Remote Logic® 259
Note:The .exe files are usually located in C:\Program Files\Remote 
Logic\Bin.
Example of a command line parameter
The example below shows how to start the controller applications with the 
configuration file Myconfig.cfg, connected to the MyTCS400 server. The 
first language is set to UK English and the second language is set to French.
C:\Program Files\Remote Logic\Bin\AL.exe
configFile=Myconfig.cfg server=MyTCS400 language1=en country1=GB 
language2=fr country2=FR.
Downloaded From ManualsPrinter.com Manuals 
						

							260 Océ TCS400 User manual
Connect to the controller
Introduction
After you start one of the Océ Remote Logic® applications, you must connect 
to the Océ Power Logic® controller of the Océ TCS400. You must connect to 
the system for every separate application.
You can perform the following when you connect to the controller: 
■Select a system from the drop-down list.
■Add a system to the drop-down list.
■Remove a system from the drop-down list.
If the Océ TCS400 is not available in the Connect to dialog box, you must add 
the Océ TCS400 to the list of available systems.
How to connect to a system
1
Open the application you want to run.
2From the File menu, select Connect to.
3Select the system from the drop-down list.
4Click OK.
Note:From the File menu, select Options to define the default system. This 
is recommended if you frequently connect to the same system.
How to add a system
1
From the File menu, select Connect to.
2Click Edit.
The Edit systems dialog box appears.
3Enter the IP address or the name of the system in the Systems box.
4Click Add.
The system is added to the list.
5Click OK two times to return to the application.
Downloaded From ManualsPrinter.com Manuals