Nortel Compact Ics 6.0 Installer Guide

Telco features / 241
P0992669 03Compact ICS 6.0 Installer Guide
For Analog VSC
4. Press 
≠. The display shows Tone:None .
5. Press CHANGE to enter a new tone dialing Name and Number blocking 
digit sequence.
6. Press 
‘. The display shows Pulse:None.
7. Press CHANGE to enter a new pulse dialing Name and Number blocking 
digit sequence.
For BRI VSC
8. Press 
≠. The display shows Code .
9. Press CHANGE to enter a new ONN code. 

242 / Software Keys
Compact ICS 6.0 Installer GuideP0992669 03
Software Keys
In order to upgrade a restricted feature cartridge or enable the remote 
administration feature (I-RAD) you must first purchase the required 
Software keys. To obtain the required Software key, call the Integrated 
Voice Response (IVR) access line at: 1-800-4NORTEL (667835), then 
use Express Routing Code 1599.
Entering the keys is done using the following programming settings under 
Software Keys.
SysID
Press ≠ at Software...

Hardware / 243
P0992669 03Compact ICS 6.0 Installer Guide
Hardware
Hardware is where you view and change the settings for the Trunk 
Cartridges and BRI Cards installed in the ICS. 
The ISDN section provides an overview of configuration and programming 
for ISDN resources, including step-by-step instructions for programming. 
This section provides more detailed information about individual headings 
and settings.
Hardware settings that appear for each cartridge or card type
Setting Loop 
start...

244 / Hardware
Compact ICS 6.0 Installer GuideP0992669 03
Cd1-KSUInstaller password required
Press ≠ to display the Trunk Cartridge or BRI Card in the ICS. 
Press 
CHANGE to select a card type: Loop, BRI-U2, BRI-U4, or BRI-ST.
If your system is using a restricted feature cartridge that has not been 
upgraded, you cannot select the BRI-ST and BRI-U4 card types, or 
configure the second cartridge or card in the ICS (
Cd2-KSU). 
KSU is commonly referred to as the Integrated Communication System 
(ICS).
Card...

Hardware / 245
P0992669 03Compact ICS 6.0 Installer Guide
Discon timerInstaller password required
Disconnect timer allows you to specify the duration of an open switch 
interval (OSI) before a call on a supervised external line is considered 
disconnected. 
Press 
CHANGE to select the setting: 60, 100, 260, 460, or 600 milliseconds.
LoopsInstaller password required
The display shows the loops found on the BRI Card.
If your system is using a restricted feature cartridge that has not been 
upgraded, you...

246 / Hardware
Compact ICS 6.0 Installer GuideP0992669 03
TypeInstaller password required
Press CHANGE to select the loop type. If the card type is BRI-ST, the loop 
type can be S, or T. If the card type is BRI-U2 or BRI-U4, the loop type 
can be LT or NT.
The BRI Card must be disabled under Module Status in Maintenance 
before this setting can be changed. You can change the setting if the card 
has not yet been installed in the ICS slot.
LinesInstaller password required
There are two lines for each T,...

Hardware / 247
P0992669 03Compact ICS 6.0 Installer Guide
When the loop type is T or NT, calls on the loop are handled for a network 
connection only. If any other ISDN equipment is connected to the loop, it 
must be configured as an S loop to ensure proper call handling.
Press 
ADD and enter the first or second SPID assigned to the loop. 
If there are two SPIDs already assigned to the loop, 
ADD will not appear 
until one is removed.
Press 
REMOVE to clear a SPID.
Note: SPIDs are not required for...

248 / Hardware
Compact ICS 6.0 Installer GuideP0992669 03
Network DNsInstaller password required
Press ≠ to display the DNs which are used with the SPID.
Press 
ADD and enter the appropriate number to assign additional Network 
DNs to the SPID.
The Compact ICS can have a maximum of 32 Network DNs for the system. 
There is no limit to the number of Network DNs for each SPID, but you 
cannot exceed the limit of 32 Network DNs for the system.
If the Network DN you try to enter is already assigned to a SPID...

Hardware / 249
P0992669 03Compact ICS 6.0 Installer Guide
D-packet servcInstaller password required
Press ≠ to view and program D-packet service for S, T, or NT-
loops. You can have two D-packet service configurations for each BRI 
Card.
D-packet servcInstaller password required
Press CHANGE to turn D-packet service for this loop on (Y) or off (N).
Lp201Installer password required
Select the S loop (for BRI-ST cards) or LT loop (for BRI-U2 or BRI-U4 
cards) that supports the D-packet service.
Press...

250 / Hardware
Compact ICS 6.0 Installer GuideP0992669 03
SamplingInstaller password required
Press CHANGE to select the sampling used by an S loop: 
Fixed: if two or more S-interface devices use the loop and the length 
of the loop is less than 200 m (650 ft), select Fixed.
Adaptve: if two or more S-interface devices use the loop and the length 
of the loop is greater than 200 m (650 ft), select Adaptve.
If one S-interface device is using the loop, the length of the loop can be up 
to 1000 m (3,250...