Nortel Compact Ics 6.0 Installer Guide

Passwords / 191
P0992669 03Compact ICS 6.0 Installer Guide
Use CHANGE, the dialpad, and OK to program the System Coordinator Plus 
password.
SysCoord
The default System Coordinator password is 23646 (ADMIN).
Basic
The default Basic password is 22742 (BASIC).
IRAD pswd
The ability to do remote programming using the internal remote access 
device (I-RAD) is protected by a password. If your Feature Cartridge does 
come with the I-RAD enabled, the feature is not available until you enter 
Software Keys...

192 / Passwords
Compact ICS 6.0 Installer GuideP0992669 03
The I-RAD password returns to the default value when you upgrade the 
system software from CICS 1.0 or 2.0 to CICS 6.0.
Hospitality password
There are two passwords within the hospitality feature. One provides 
secure access to the administration set, and one provides secure access to a 
room condition setting from each room set for housekeeping staff.
Desk pswd
Change this password frequently, to maintain security.
At Hospitality:
1. Press 
≠....

Time&Date / 193
P0992669 03Compact ICS 6.0 Installer Guide
Time&Date
The time and date shown on the telephone display is used by the system for 
scheduled features. It can be changed in programming or by using a feature 
code (
²¥¥æé÷ä or ²¥¥¡ÝßÜ).
For more information, see the Compact ICS 6.0 System Coordinator Guide. 

194 / System prgming
Compact ICS 6.0 Installer GuideP0992669 03
System prgming
System prgming allows you to set up features and settings which are not 
associated with any specific line or telephone.
Hunt groups
The hunt groups feature allows a group of sets to be called by a single 
directory number ensuring that calls are easily routed to the appropriate 
group. 
The default setting for hunt groups is broadcast mode. Sequential or rotary 
modes are also available. 
Hunt groups can be used to route...

System prgming / 195
P0992669 03Compact ICS 6.0 Installer Guide
The hunt group setting impacts other features:
Call forwards set  on telephones that are members of a hunt group are 
overridden by the hunt group routing. 
Sets that are members of a hunt group can temporarily leave a group 
by activating the DND feature.
Priority calls to a hunt group will be rejected
Hunt group set numbers cannot be in a ring group.
Hunt group set numbers cannot be in a page zone.
Note: Fixed external cadencing is...

196 / System prgming
Compact ICS 6.0 Installer GuideP0992669 03
6. Press ADD to add a member or press REMOVE to remove a member from 
the group.
7. Select Appr&Ring, Appr only or Ring only setting for hunt group 
member. See Line assignment on page 137.
Moving members of a group
Member order within a hunt group is important. Calls are routed starting 
with the first member, except in Broadcast mode, when calls are sent 
simultaneously to all members.
1. Press 
MOVE to move an existing member to another...

System prgming / 197
P0992669 03Compact ICS 6.0 Installer Guide
Assigning a distinctive ring pattern to a Hunt Group
You can assign distinctive ring patterns to your Hunt Group so that calls 
can be rated in priority for the group.
These distinctive ring patterns, have the same characteristics as for line and 
extension distinctive ring patterns. Refer to Distinctive ring on page 163.
The Hunt Group distinctive ring pattern determines how a call will ring 
within the Hunt Group. If members of the group...

198 / System prgming
Compact ICS 6.0 Installer GuideP0992669 03
Sequential—starts the call at the first set in the hunt group and 
distribution is complete when the first free set has been found. 
Simultaneous calls can be presented. Distribution is order based.
In Sequential mode, you can program your top salesperson to be the 
first member of the group to receive incoming calls.
Rotary—the call starts at the set after the one which was last presented 
and distribution is complete when the next free...

System prgming / 199
P0992669 03Compact ICS 6.0 Installer Guide
available. When the time-out occurs, the call will be presented to an 
overflow position.
1. When the display shows
 Member DNs:.
2. Press 
‘ until the display shows If busy:. 
3. Press 
CHANGE to set the mode: BusyTone, Overflow, Queue.
Programming the queue timeout
This setting allows you to program the number of seconds a call will 
remain in the hunt group queue before it is routed to the overflow position.
1. When the display shows...

200 / System prgming
Compact ICS 6.0 Installer GuideP0992669 03
Setting the function name
This setting allows you to program the hunt group function name, such as 
SERVICE or SALES. The name can be up to seven characters in length.
1. When the display shows
 Member DNs:.
2. Press 
‘ until the display shows Name:. 
3. Press 
CHANGE.
4. Using the dialpad, enter the name of the hunt group.
5. Press 
‘ to store the name.
Change DNs
Change DNs allows you to change the directory number (DN) or internal 
number...