Nortel Compact Ics 6.0 Installer Guide

Services / 181
P0992669 03Compact ICS 6.0 Installer Guide
Programming for least cost routing
It may be cheaper to use another long distance carrier at another time of 
day. Continuing with the example used in the flowchart, long distance calls 
will go out on the same lines without an access code at Night because that 
is when rates become competitive. For the system to do this automatically, 
another route has to be built.
choose Route 007 (or any other available route) at 
Show Route:
press CLR to...

182 / Services
Compact ICS 6.0 Installer GuideP0992669 03
Calls that begin with the digits 91 will now travel out without using the 
access code when the Night schedule comes into use automatically, or 
when it is turned on at a control telephone.
Night schedInstaller password required
Indicate how the alternate routing should be activated for each of the 
schedules.
Service
Use ≠, ‘, and CHANGE to change the setting for each 
schedule: Off, Automatic, or Manual.
See Ringing service in this section for...

Services / 183
P0992669 03Compact ICS 6.0 Installer Guide
Using dialing restrictions with routing
Routing service can be further customized by adding dialing restrictions to 
lines in line pools. Filters can restrict the use of the line to specific area 
codes. See the Networking features section of the Networking with Norstar 
on page 41, and Restrictions under both the Terminals&Sets and Lines 
programming sections for more information.
  Host system signaling codes
Tip - Host system signaling codes...

184 / Services
Compact ICS 6.0 Installer GuideP0992669 03
Common settings
Services share the settings for control telephones, schedule names and 
schedule times.
Control sets
A control telephone turns Services on and off for the lines and/or 
telephones assigned to it. 
You can assign several control telephones for your system. 
A control telephone for lines controls Ringing service, Restriction 
service and Routing service for its assigned lines. 
A control telephone with assigned telephones controls...

Services / 185
P0992669 03Compact ICS 6.0 Installer Guide
Schedules names
The schedule name is shown on the display of the control telephone when 
the schedule is turned on. It identifies the active schedule.
Use 
≠, CHANGE, ‘, and the dialpad to program the 
name.
A service can be turned on manually or automatically for 
all external lines and telephones controlled by a given 
control telephone, but you cannot combine schedules. In 
other words, a service can only be active as normal 
service or one of...

186 / Services
Compact ICS 6.0 Installer GuideP0992669 03
Schedule times
Schedule start and stop times are set at times you are most likely to want 
each service to be active. Use 
≠, CHANGE, ‘, and the 
dialpad to program the start and stop times for each schedule, on each day. 
Default schedule times
You can copy schedule times using 
COPY to make the programming easier. 
The following example shows how to program Night Schedule to start at 
5:00 p.m. on Monday through Friday, and end at 8:00 a.m. the...

Sys speed dial / 187
P0992669 03Compact ICS 6.0 Installer Guide
Sys speed dial
System speed dial allows you to create speed dial codes that can be used by 
any telephone in the system.
For CICs version 6.0 the number of system speed dial codes has been 
increased to 200 (001 to 255). The user speed dial codes have been adjusted 
to the 256-279 range.
If you specify a name with the speed dial entry, an incoming call on a CLID 
line with a dialed number that matches the speed dial entry will display the...

188 / Passwords
Compact ICS 6.0 Installer GuideP0992669 03
Passwords
COS pswds
Class of Service (COS) passwords permit controlled access to system 
resources by both internal and remote users. When you enter a Class of 
Service password at a telephone, the restriction filters associated with your 
Class of Service password apply instead of the normal restriction filters. 
Similarly, when a remote user enters a Class of Service password on an 
incoming auto-answer line, the restriction filters and remote...

Passwords / 189
P0992669 03Compact ICS 6.0 Installer Guide
Pswd
Pswd defines the six-digit Class of Service password. There is no default 
password.
Use 
≠, CHANGE, and the dialpad to program the six-digit 
password. Use 
BKSP to edit numbers you have entered.
User flt
User filter allows you to assign a restriction filter to a Class of Service 
password. The user filter associated with the Class of Service password 
replaces any normally applicable set restriction, line/set restriction, and 
remote...

190 / Passwords
Compact ICS 6.0 Installer GuideP0992669 03
Call log pswds
This setting allows you to override any Call log password programmed 
with the Call log feature, and resets it to None. It is used when someone 
forgets a password. Press 
≠ and enter the DN of the telephone. 
Press 
≠ and then CLR to clear the programmed password.
Programming pswds
You can choose any combination of six digits for Passwords. It is easier to 
remember the password if the digits spell a word. 
Provide passwords only...