Nortel Compact Ics 6.0 Installer Guide

Startup programming / 131
P0992669 03Compact ICS 6.0 Installer Guide
Changing the default template
After entering the Startup access code and Installer password the display 
shows
 Reset memory?.
1. Press 
YES to select a default template. The display shows the current 
template.
2. Press 
CHANGE to choose one of three templates (Square, PBX, or 
Hybrid). With the display showing the current template.
3. Press 
‘. The display shows the current start DN.
4. Press 
CHANGE.
5. Enter the new directory number...

132 / Startup programming
Compact ICS 6.0 Installer GuideP0992669 03
Programming may be lost after three or more 
days without power.
All programming is retained for three days if the 
power fails or if the Norstar system is powered off. 
After three days without power, it may be 
necessary to perform Startup.
Tip - The length of the new DN (internal number) can 
be from two to seven digits.
Note: Systems that want to use Hunt Groups or 
Hospitality Services must have a minimum of three-digit 
DNs.
The...

Programming / 133
P0992669 03Compact ICS 6.0 Installer Guide
Programming
After performing Startup, use programming to change default settings as 
required. Default settings for the Square template are shown in bold.
Headings and subheadings in programming help you to keep track of where 
you are.
 Programming has the following main headings:
Terminals&Setsallows you to assign settings to each telephone.
Linesallows you to assign settings to each trunk, external 
and target line.
Servicesallows you to...

134 / Programming
Compact ICS 6.0 Installer GuideP0992669 03
Entering programming for installers
1. Press ²¥¥‚¯öìéí which is the same as 
²¥¥ÛßßÜÝÝ. The display shows Password:.
2. Enter the Installer password. The default password is CONFIG 
(266344). The display shows
 Terminals&Sets ˆ. Three triangular 
indicators 
º appear on the vertical display between the rows of 
buttons.
3. Place the programming overlay over the buttons pointed to by the 
indicators 
º.
Entering programming for system...

Programming / 135
P0992669 03Compact ICS 6.0 Installer Guide
Entering programming using other passwords
A set of the most often used headings and subheadings is available by using 
a System Coordinator password (see page 116). This level of access is 
designed for the person who takes care of the day-to-day changes to the 
Norstar system, but who is not interested in more advanced programming. 
The default password is ADMIN (23646).
There is also a Basic password that can be used to perform a few...

136 / Terminals&Sets
Compact ICS 6.0 Installer GuideP0992669 03
Terminals&Sets
Terminals&Sets allows you to assign settings to each telephone.
Press 
≠ and enter the extension number of the telephone you 
would like to program.
Press 
COPY to duplicate the programming for the telephone and apply it to 
another telephone, a range of telephones or all the telephones on the 
system. For more information about copying set programming, see 
Copying telephone programming on page 122.
Line access
Line access...

Terminals&Sets / 137
P0992669 03Compact ICS 6.0 Installer Guide
Line assignment
This setting allows you to assign physical trunks and target lines to each 
telephone. Target lines are assigned and removed in the same manner as 
other lines. Press 
≠ and enter the line number. Press CHANGE to 
change the setting for each line: Appr&Ring, Appr only, Unassigned, or 
Ring only. Broadcast ring group  ability is  possible with multiple target line 
assignment across a group of sets. 
Tip - Press SCAN to view...

138 / Terminals&Sets
Compact ICS 6.0 Installer GuideP0992669 03
Appearances
This setting only applies for direct  inward dial (DID) digits mapped onto 
target lines.
The Norstar system can handle simultaneous calls to set with multiple 
target line appearances. The number of target line appearances depends on 
the line assignment setting, which include: Appr&Ring, Ring only, Appr 
only.
If Appr&Ring or Appr only is chosen, you can have as many simultaneous 
DID calls as there are target line key...

Terminals&Sets / 139
P0992669 03Compact ICS 6.0 Installer Guide
Prime line
This setting assigns a prime line to the telephone. A prime line is the first 
line that is automatically selected when the handset is lifted. 
Press 
CHANGE to select the setting: None, a line number, 
Pool (A to C), and I/C (intercom). Only assigned lines and line pools 
appear.
Tip - An assigned prime line is not associated with the 
assignment of a prime telephone.
An external line must be assigned to the telephone in 
Line...

140 / Terminals&Sets
Compact ICS 6.0 Installer GuideP0992669 03
Intercom keys
This setting assigns the number of intercom buttons to a telephone. 
Intercom buttons can provide a telephone with access to internal lines and 
line pools. Press 
CHANGE to select the setting: 0, 1, 2, 3, 4, 5, 6, 7, or 8.
Answer DNs
Calls for other Norstar telephones can appear and be answered at the 
telephone being programmed. The DNs of the other telephones are referred 
to as Answer DNs. You can assign up to eight Answer...