Nortel Compact Ics 6.0 Installer Guide

Terminals&Sets / 151
P0992669 03Compact ICS 6.0 Installer Guide
Line/set restrns
Line/set restrns allows you to assign a restriction filter to a specific line that 
can be used for outgoing calls at a specific telephone. This type of filter 
replaces any line or set restriction filters which might otherwise apply. It 
restricts the numbers you can dial on a line, but only from that telephone. 
The same line on another telephone can have different restrictions.
As with set restrictions, you can apply a...

152 / Terminals&Sets
Compact ICS 6.0 Installer GuideP0992669 03
Feature assignment (CLID alignment)
If you subscribe to Call Display services (often called Caller ID) and the 
Compact ICS is equipped with a Global Analog Trunk Cartridge (GATC) 
with CLID (or a Call Information (CI) Trunk Cartridge), external calls are 
identified on the display. You may also have a message indicator from an 
external voice mail service show on the display. CLASS assignment 
programming allows you to customize how this...

Terminals&Sets / 153
P0992669 03Compact ICS 6.0 Installer Guide
Extl VMsg set
If you subscribe to a voice message service, you can access that service 
through your Norstar system. The external voice message setting controls 
where the indicator shows up when there is a voice message waiting on a 
particular line. The line must appear on that telephone. Press 
CHANGE to 
select the setting: N(No) or Y (Yes).
1st Display
Depending on the services you subscribe to, Call Display information may 
contain up...

154 / Terminals&Sets
Compact ICS 6.0 Installer GuideP0992669 03
Log space
Log space determines the number of items that can be stored in the Call log 
for each telephone. Use 
≠, ADD and REMOVE to redistribute the log 
space. There is no log space assigned by default.
Tip - There must be space available in the log pool in 
order for you to add space to a Call log. The maximum 
number of spaces available is 250.
System-wide log space allocation is performed in Call log 
space under System prgrming. If you...

Lines / 155
P0992669 03Compact ICS 6.0 Installer Guide
Lines
Trunk/Line dataInstaller password required
Trunk/Line data allows you to program settings for lines that affect how the 
Norstar communicates with the public network and other switches. Line 
data allows you to determine how lines (including target lines) will be used 
in the Norstar system.
Some Trunk/Line data settings may not appear on the display during 
programming depending on the type of trunk. Those that appear for a given 
Trunk type...

156 / Lines
Compact ICS 6.0 Installer GuideP0992669 03
Copying Trunk and Line data
At the Trunk/Line data ˆ display COPY appears. This allows you to copy 
programming from one line to other lines.
Trunk typeInstaller password required
Trunk type shows the type of Trunk Cartridge or BRI Card on which the 
line is found. It can be Loop, BRI-ST, BRI-U2, or BRI-U4.
Tip - In copying data from a physical trunk to a target 
line (or the other way around), only the data in common 
is copied. For example, copying...

Lines / 157
P0992669 03Compact ICS 6.0 Installer Guide
Line typeInstaller password required
This setting specifies how the line is to be used in the system. Press CHANGE 
to select the setting: Public, Private to:, or Pool (A to C).
A public line can be accessed by more than one telephone.
A private line can be assigned only to one telephone and  the prime 
telephone for that line. Use 
CHANGE and the dialpad to enter the 
internal number of the telephone.
If you try to make private a line that is...

158 / Lines
Compact ICS 6.0 Installer GuideP0992669 03
Dial modeInstaller password required
Dial mode allows you to specify whether dual tone multifrequency 
(DTMF) or pulse signalling is used on the trunk. Press 
CHANGE to select the 
setting: Pulse or Tone.
Prime setInstaller password required
This feature allows you to assign a telephone to provide backup answering 
for calls on the line. Unanswered calls are redirected to the prime telephone 
if DRT to prime is set to Yes. Use 
CHANGE and the dialpad...

Lines / 159
P0992669 03Compact ICS 6.0 Installer Guide
Auto privacyInstaller password required
This feature controls whether one Norstar user can select a line in use at 
another telephone to join an existing call. The default setting is Privacy on, 
so that nobody with a Norstar telephone can press a line appearance on 
their telephone to join a call in progress at another telephone. Press  
CHANGE 
to select the setting: Y (on) and N (off).
Trunk modeInstaller password required
Trunk mode allows you to...

160 / Lines
Compact ICS 6.0 Installer GuideP0992669 03
Ans modeInstaller password required
The Answer mode setting appears on the display during programming for 
loop start and BRI trunks if the Trunk mode setting is Super. Press 
CHANGE 
to select the setting: Manual or Auto.
Ans with DISAInstaller password required
When activated, the Answer with DISA setting specifies that a trunk is 
answered with stuttered dial tone. Press 
CHANGE to select the setting: 
Y (Yes) or N (No).
Aux. ringerInstaller...