Nortel Compact Ics 6.0 Installer Guide

Installing Norstar telephones / 101
P0992669 03Compact ICS 6.0 Installer Guide
Mounting on the wall using the angled base
Mount the keystation 
    onto the screws and 
slide it down. Mount the stand as shown and
insert screw. Use the screw that
came with your keystation.
 
key hole slots
Connect line cord to 
wall jack. Connect cords to the keystation,
   refer to cord connections
 
Tighten screws for a secure fit. Use the key hole slots on the stand
to mark the location for the screws. 

102 / Installing Norstar telephones
Compact ICS 6.0 Installer GuideP0992669 03
Installing Norstar telephones
Tip - Norstar telephones and telephones 
connected using the internal analog terminal 
adapter (I-ATA) cannot be used as off-premise 
extensions (OPX or OPS). For OPX applications, 
use the Norstar Analog Terminal Adapter (ATA) 
and a single-line telephone. See the 
ATA 
Installation Card
 for details.
Connect to 
jack wired from
distribution block
Connect to 
receiver 

Installing Norstar telephones / 103
P0992669 03Compact ICS 6.0 Installer Guide
Mounting Norstar telephones on the wall
12
34
56
Mount to a suitable mounting surface. 

104 / Installing Norstar telephones
Compact ICS 6.0 Installer GuideP0992669 03
Moving telephones
You can move a telephone to a new location within the Norstar system 
without losing its programmed settings. When Set relocation (automatic 
telephone relocation) is turned on in System programming, the internal 
numbers, autodial settings, and user speed dial codes remain with the 
telephone when it is unplugged. To move a telephone, simply unplug it and 
plug it in again at another location. It may take up...

Installing ISDN terminal equipment / 105
P0992669 03Compact ICS 6.0 Installer Guide
Installing ISDN terminal equipment
For each S, T or U-LT reference point, an eight-position miniature unkeyed 
plug from the terminal equipment (TE) is plugged into a jack connected to 
Norstar wiring. The pin connections for the jack and plug are shown in the 
following charts.
For point-to-multipoint operation on S or T loops, ensure the wiring 
polarity integrity is maintained. 
S or T wiring for terminal equipment
S...

106 / Installing ISDN terminal equipment
Compact ICS 6.0 Installer GuideP0992669 03
The maximum length of spur and ISDN connection cord (the extension 
from the main line or bus) is 10 m (30 ft). 
See the ISDN chapter for information about wiring arrangements for ISDN 
terminal equipment (TE) on an S or T loop.
Additional power
 A Norstar S-loop does not provide power on Power Source 1 (PS1), Power 
Source (PS2), or Power Source or Sink 3 (PS3). If you are installing ISDN 
terminal equipment at the...

Installing ISDN terminal equipment / 107
P0992669 03Compact ICS 6.0 Installer Guide
No power supply is provided for the U-LT wiring. If equipment attached to 
the U-LT loop requires optional power, install an approved power supply 
unit. See ANSI T1.601-1992 Annex H or the documentation that comes 
with your TE for more information.
Jack and plug pin numbering     
8  7  6  5  4  3  2  1
1       2      3       4       5       6     7       8    

108 / Installing optional equipment
Compact ICS 6.0 Installer GuideP0992669 03
Installing optional equipment
Auxiliary ringer (customer supplied)
The Norstar ICS provides a control contact to operate an auxiliary ringer. 
1. Follow the manufacturer’s installation instructions.
2. Connect the auxiliary  ring generator to  the 25-pair distribution block 
as shown in the wiring charts. The pins in the chart provide a control 
contact. They do not provide ring current or dc voltage. The contact is 
capable...

Installing optional equipment / 109
P0992669 03Compact ICS 6.0 Installer Guide
External music source programming
Music for callers on Hold and for Background Music must be enabled 
through programming. Refer to the Programming chapter for more details. 
Refer specifically to the following Programming headings and confirm that 
the following settings are implemented:
External paging system (customer supplied)
You can connect an external paging system to provide paging over external 
loudspeakers. The...

110 / Installing optional equipment
Compact ICS 6.0 Installer GuideP0992669 03
 
Tip - Norstar external paging does not support 
talk-back paging equipment unless an external line 
port is used.
The Norstar system provides paging over the 
Norstar telephone speakers, even when no 
external paging equipment is connected.
Install all optional equipment before powering up 
the system.