NEC Neax 2400 Imx Hotel Office Data Specification

							NDA-24288 CHAPTER 4
Page 229
Revision 1.0
ASPS
(k) Paging Answer Code (SRV = PAGA)
DAY/NIGHT
(D/N)
D/NASSIGN NUMBER
(No.)
0 – 63DEVELOP
NUMBER
(F)
0 – 15KIND OF SERVICE
(SRV)ROUTE NUMBER
(RT) 
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A
PA G A 
						

							CHAPTER 4 NDA-24288
Page 230
Revision 1.0
ASPS
(l) Paging Cancel Code (SRV = PAGC)
DAY/NIGHT
(D/N)
D/NASSIGN NUMBER
(No.) 
0 – 63DEVELOP
NUMBER
(F) 
0 – 15KIND OF SERVICE
(SRV) ROUTE NUMBER
(RT)
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C
PA G C 
						

							NDA-24288 CHAPTER 4
Page 231
Revision 1.0
ASCR
ASCR: Assignment of Station Connection Restriction
1. General
This command assigns and displays the station-to-station connection restriction data based on the Route
Restriction Class (RSC) of respective tenants.
2. Precautions
1. This command is used for the Hotel Application only.
2. Station-to-station connections will be allowed for each RSC until they are restricted by this command.
3. Data Entry Instructions
CALLING TN
       RSC
Calling Tenant Number
           respective Route Restriction ClassDIAL/ATT
Designate whether restriction applies
to stations or attendant
0/1 = Dial/Attendant
 CALLING
  TENANT
 NUMBER
(CALLING
     TN)    CALLING
RESTRICTION
      CLASS
   (RSC) 0-15    CALLED
RESTRICTION
     CLASS
  (RSC) 0-15 DAY/NIGHT
    MODE
     (D/N)
       D/N   DIRECT
DIAL FROM
  STA/ATT
 (DIAL/ATT)
       0/1RESTRICTION
 RESTRICTED
   /ALLOWED
        (RES)
          0/1
CALLED TN
      RSC
Called Tenant Number
             respective Route Restriction ClassD/N
RES
D : Day Mode
N : Night Mode0 : Restricted
1 : Connection is allowed      
  CALLED
  TENANT
 NUMBER
(CALLED
     TN)
  
						

							CHAPTER 4 NDA-24288
Page 232
Revision 1.0
ASCR
4. Data Sheet
CALLING
TENANT
NUMBER
(CALLING
TN)CALLED
TENANT
NUMBER
(CALLED
TN)CALLING
RESTRICTION
CLASS
(RSC)
0 – 15CALLED
RESTRICTION
CLASS
(RSC)
0 – 15DAY /NI GHT
MODE
(D/N)
D/NDIRECT DIAL
FROM STA/ATT
(DIAL/ATT)
1/2RESTRICTION
RESTRICTED/
ALLOWED
(RES)
0/1 
						

							NDA-24288 CHAPTER 4
Page 233
Revision 1.0
AT C R
ATCR:    Assignment of Telephone Class Restriction
1. General
This command assigns and displays the restriction data for connections between Telephone Equipment Classes
(TECs).
2. Precautions
1. This command is used for the Hotel Application only.
2. Connection between TECs will be allowed for each RSC until they are restricted by this command.
3. TEC 31 is used for ATT in this command.
3. Data Entry Instructions
CALLING TEC
Calling Telephone Equipment Class
1: DP (10 pps) 2: PB
3: DP/PB 4: DP (20 pps)
5: DP (10 pps) : Guest 6: PS : Guest
7: DP/PB : Guest 8: DP (20 pps) : Guest
9: House Phone 10: House Phone : Guest
11: Not Used 12: D
term       
13: Data Terminal via Dterm14: Hot Line
15: CAS Line 16: Data Terminal via Data Module
17: Not Used 18: Virtual Line Appearance (for D
term Multi-Line)
19-22: Not Used 23: ISDN Terminal
24-25: Not Used 26: Not Used
27: Eight Conference Equipment
28-30: Not Used 31:ATT    
CALLED TEC
Called Telephone Equipment Class
1 : DP (10 pps) 2 : PB
3 : DP/PB 4 : DP (20 pps)
5 : DP (10 pps) : Guest
 6 : PS : Guest
7 : DP/PB : Guest 8 : DP (20 pps) : Guest
9 : House Phone 10 : House Phone : Guest
11 : Not Used 12 : D
term       
13 : Data Terminal via Dterm14 : Hot Line
15 : CAS Line1 6 : Data Terminal via Data Module
17 : Not Used 18 : Virtual Line Appearance (for D
term Multi-Line)
19-22 : Not Used 23 : ISDN Terminal
24-25 : Not Used 26 : Not Used
27 : Eight Conference Equipment
28-30 : Not Used 31 : ATT    
     CALLING
  TELEPHONE
 EQUIP. CLASS
(CALLING TEC)
         1-31     CALLED
  TELEPHONE
 EQUIP. CLASS
(CALLED TEC)
         1-31DAY/NIGHT
     MODE
      (D/N)   
       D/NRESTRICTION
       (RES)
         0/1
RES
0 : Restricted
1 : Connection is allowed
D/N
D : Day Mode
N : Night Mode 
						

							CHAPTER 4 NDA-24288
Page 234
Revision 1.0
AT C R
4. Data Sheet
 
CALLING
 TELEPHONE
 EQUIP. CLASS
(CALLING TEC)
1 – 31CALLED
 TELEPHONE
 EQUIP. CLASS
(CALLED TEC)
1 – 31DAY/NIGHT MODE
(D/N)
D/NRESTRICTION
(RES)
0/1 
						

							NDA-24288 CHAPTER 4
Page 235
Revision 1.0
ADNR
ADNR: Assignment of Day/Night Restriction
1. General
This command assigns and displays the specific Start and End times pertaining to Day/Night Restriction or to
display the Day/Night Restriction classification of a specific time.
2. Precautions
1. This command is used for the Hotel Application only.
2. When Data “1” is assigned for bit6 of the ASYD command, SYS1, INDEX 170, Day/Night Connection
Restriction will be executed regardless of ATT night mode changeover.
3. The ARSC command may be affected if the day and night tables are used.
4. For time designation, use military time (24 hour cycle) in units of 10 minutes.
5. End time must be later than Start time. If the same time is specified for both Start and End, the restriction
period will be 10 minutes.
6. Night time assignment should be input twice; once for the period before midnight, and once for the period
after midnight because midnight is assigned as hour 00:00. Refer to the example below for clarification:
Example:If the time period from 9:00 p.m. to 7:00 a.m. is to be assigned as Night,
00:00 - 07:00 = Night
07:10 - 20:50 = Day
21:00 - 23:50 = Night
7. RSC 11 through 15 may be used in the Same Special Code Time Zone Connection Change service (The
AASP/AGSP command, SRV = 2, SID 36, STATE 51- 55).
3. Data Entry Instructions
D/N RSC
TENANT
NUMBER 
    (TN)DAY/NIGHT
    MODE
     (D/N)
      D/N      ROUTE
RESTRICTION
      CLASS
       (RSC)
        0-15RESTRICTION
  START TIME
 (START TIME)  
   00:00-23:50RESTRICTION
    END TIME
   (END TIME)
   00:00-23:50
START TIMEEND TIME D : Day Mode
N : Night ModeRSC 0      : ATT
RSC 1-15 : Station
Assign in military time (24 hour cycle)
in units of 10 minutes.Assign in military time (24 hour cycle)
in units of 10 minutes. 
						

							CHAPTER 4 NDA-24288
Page 236
Revision 1.0
ADNR
4. Data Sheet
TENANT
NUMBER
(TN)DAY /NI GHT
MODE
(DAY/NIGHT)
D/NROUTE
RESTRICTION CLASS
(RSC)
0 – 15RESTRICTION
 START TIME
 (START TIME)
00:00 – 23:50RESTRICTION
END TIME
 (END TIME)
 00:00 – 23:50
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
::
:: 
						

							NDA-24288 CHAPTER 4
Page 237
Revision 1.0
AAST
AAST: Assignment of Administration Station Data
1. General
This command assigns the administration station data. 
2. Precautions
1. This command is used for the Hotel Application only.
2. When deleting station data, use the RAST command.
3. The AASN command is used to change the station number, and the AACL command is used to change the
Class data (TEC, RSC, SFC etc.).
4. Assignment of Room Class 15 is not available.
5. The number of digits for a station number are designated by the ASYD command, SYS1, INDEX 16. The
maximum number of digits for a station is 6.
6. The first digit of the station number is designated by the AANP command.
7. The RSC and SFC data work in conjunction with ARSC/ASCR/ADNR and ASFC commands. 
						

							CHAPTER 4 NDA-24288
Page 238
Revision 1.0
AAST
3. Data Entry Instructions
  1 : DP (10 pps) 2 : PB      
  3 : DP/PB 4 : DP (20 pps)
  5-8 : Not Used 9 : House Phone               
 10-11 : Not Used 12 : D
term
  13 : Data Terminal via Dterm                  
  14 : Hot Line1 5 : CAS Line
  16 : Data Terminal via Data Module               
 17 : Not Used
  18 : Virtual Line Appearance (for D
term Multi-Line)
  19-22 : Not Used 23 : ISDN Terminal       
  24-25 : Not Used 26 : Not Used
  27 : Eight Conference Equipment                
 28-31 : Not UsedTEC
LENS
Enter the LENS
XX X XX X
                                           Level No. (0-7)
                                           Group No. (00-31)
                                           Unit No. (0-3)
                                           Module Group No. (00-31)
G
0 : Ground
1 : Underground
TENANT
NUMBER
   (TN)    STATION
  NUMBER
     (STN)
Max.6 digitsTELEPHONE
EQUIPMENT
    CLASS
     (TEC)
      1-31     ROUTE
RESTRICTION
     CLASS
      (RSC)
       0-15SERVICE
FEATURE
  CLASS
   (SFC)
    0-15ROOM
CLASS
   0-15ANNEX
 (ANX)
   0-3    GROUND/
UNDERGROUND 
           (G)
           0/1FLOOR
  (FLR)
  1-127 LINE EQUIPMENT
       NUMBER
         (LENS)
MG      U       G       LV
ANNEX
0 : Main Building
1 : Annex 1
2 : Annex 2
3 : Annex 3
RSC
Enter the RSC defined by the ARSC command. Since RSC = 0 is
preserved for ATTCON, a station can use the RSC range from 1 to 15.
SFC
Enter the SFC defined by the ASFC command. Since SFC = 0 is
preserved for ATTCON, a station can use the SFC range from 1 to 15.
0 : General Administration  (Ordinary Telephone, D
term)    
1-5 : Not used
6 : Guest Service Telephone (D
term and External Equipment)
7-15 : Not UsedRoom Class STN
Enter the station number with regard to the following:
 The number of station number (STN) digits is designated
   by the ASYD command, SYS1, INDEX 16.