NEC Neax 2400 Imx Hotel Office Data Specification

							NDA-24288 CHAPTER 4
Page 179
Revision 1.0
AGSPL
(j) Telephone Number (SRV = TELN)
 
TENANT
NUMBER 
(TN)ACCESS CODE 
(ACC)
MAXIMUM
6 DIGITSCONNECTION
STATUS INDEX
(CI) 
N/HKIND OF
SERVICE 
(SRV)NUMBER OF 
NECESSARY 
DIGITS
(NND) 
1-24REMARKS
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking
NNormal
TELN
H Hooking 
						

							CHAPTER 4 NDA-24288
Page 180
Revision 1.0
AGSPN
AGSPN: Assignment of Guest Special Access Code for NDM
1. General
This command assigns the numbering plan data for the Network Control Node (NCN). The data assigned in this
command is written in the Network Data Memory (NDM) of the Network Control Node (NCN), updating the
NDM at each Local Node (LN). 
2. Precautions
1. This command is used for the Hotel Application only.
2. If the Guest and Admin. Numbering are separated (the ASYD command, SYS1, INDEX 160, bit6 = 0),
use this command for the Guest Special Access code. For the Admin. Special Access code, use the
ASPAN command.
Note:Hotel features are available in TN1 only. If the numbering plans are separated by tenants, the purpose for
each tenant is completely separated. Admin. Station required of the guest room call must be allocated in
TN1.
3. If the numbering plan for Admin. and Guest is common (the ASYD command, SYS1, INDEX 160, bit6 =
1), this command may be used to assign the Admin. Special Access code as well. 
						

							NDA-24288 CHAPTER 4
Page 181
Revision 1.0
AGSPN
3 . Data Entry Instructions
Access code (Max. 6 digits)TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAX. 6 DIGITSCONNECTION 
STATUS INDEX
(CI) N/H/BKIND OF
SERVICE 
(SRV)
ACC
CISRV
SSCA=Service code appendix
OGCA=Outgoing call with route advance  
LCR=Least cost routing N=Normal service
H=Hooking service
B=Busy serviceSSC=Service code
OGC=Outgoing call
UNIF=Office termination
ANNC=Announcement service-single announcement
ANNCM=Announcement service-multiple announcement
TELN=Telephone NumberLCRS=Register sender LCR
15 (Speed Calling-System;
     Access)
63 (Call Park ; Retrieve) NND appears when the following SID is entered.
NND data is variable depending on SID.NND1 appears when SID=15. The number of ADC
(Abbreviation Digit Code) digits should be assigned in NND1.NND1
SERVICE INDEX
(SID) 1-63NECESSARY DIGIT
(NND)NECESSARY DIGIT FOR SPEED
CALLING (NND1) 1-24
NND
SID Number of digits for NNDAccess Code (1-24)
Access Code (1-3) When SRV=SSC (Service code except SID2, 36,
37, 38, 39, 56 and 57)  is assigned
2 (Dial Access to Attendant:
    Operator Call) FPC appears when the following SID is entered.SERVICE INDEX
(SID) 1-63FUSION POINT CODE
(FPC)
FPC
SID Number of FPC
7 (Call Pickup-Group)
19 (OG Trunk Quing; Entry)
1-253
1-253
1-253
20 (OG Trunk Quing; Cancel)
1-253
37 (Priority Call 1)
38 (Priority Call 2)
1-253
1-253
39 (Priority Call 3)1-253 When SRV=SSC (Service code), SID2, 37, 38 or 39 is assigned 
						

							CHAPTER 4 NDA-24288
Page 182
Revision 1.0
AGSPN
         STATE
(Hotel Service Code)
  1    To be cleaned without ID code
  2    Cleaning Completed without ID code
  3    Ready for Occupancy without ID code
  4    Use Not Allowed without ID code
5-8    -
  9    Maid Dial Answer Back without ID code-1
10    Maid Dial Answer Back without ID code-2
11    Maid Dial Answer Back without ID code-3
12    Maid Dial Answer Back without ID code-4
13    Maid Dial Answer Back without ID code-5
14    Maid Dial Answer Back without ID code-6
15    Maid Dial Answer Back without ID code-7
16    -
17    To be cleaned with ID code
18    Cleaning Completed with ID code
19    Ready for Occupancy with ID code
20    Use Not Allowed with ID code
21-24  -
25    Maid Dial Answer Back with ID code-1
26    Maid Dial Answer Back with ID code-2
27    Maid Dial Answer Back with ID code-3
28    Maid Dial Answer Back with ID code-4
29    Maid Dial Answer Back with ID code-5
30    Maid Dial Answer Back with ID code-6
31    Maid Dial Answer Back with ID code-7 
32    Access Code for Administration Station Call
33    Automatic Wake Up Setting, Cancel; Same Special code
34    For Guest Station Secretary Telephone; Boss/Secretary Calling
35-43  -
44    Direct Data Entry-Station (via Guest Station)
45-50  -
51    Same Special Code Time Zone Connection Change
52    Same Special Code Time Zone Connection Change
53    Same Special Code Time Zone Connection Change
54    Same Special Code Time Zone Connection Change
55    Same Special Code Time Zone Connection Change
56-62  -
63    Dummy Number
Note: STATE=1-15 are used at the time of Maid ID Code Service is not provided;
           (ASYD SYS1 INDEX 164, bit3=0)
           STATE=17-31 are used at the time of Maid ID Code Service is provided;
           (ASYD SYS1 INDEX 164, bit3=1)
SERVICE INDEX
     (SID) 1-63       STATE
36 When SRV=SSC (Service code). SID36 (Hotel Service) is assigned 
						

							NDA-24288 CHAPTER 4
Page 183
Revision 1.0
AGSPN
SERVICE INDEX
    (SID) 1-63      NO.1
56
NO.1
(Kind of Assignment Number)
  Available numbers are 0-15.
  This data is used to assign “Floor Service” data by the ASPF command.
Note: When programming “Floor Service” data,
 ASYD SYS1 INDEX 165, bit7=1 must have been assigned.
SERVICE INDEX
    (SID) 1-63NO.2KIND
57
NO.2
This parameter specifies the number (0-63) of the
access code being assigned for mutual Access.
This parameter serves as a counter for the access
codes being assigned.
Note: This parameter is used when assigning the
  details of the service by the ASPS command.
KIND: (0-3)
This parameter specifies the Split Access Parameter Classification. The data to
be assigned here depends on how the Guest and Administration stations are
differentiated.
The Guest and Administration stations may be assigned to separate TNs, RSCs,
and/or SFCs, or they may only be differentiated by their respective designations
as Administration or Guest.
      0:    Administration/Guest
             (Assign this if the access code is to be shared between Guest
             and Administration with no correspondence to TN, RSC or SFC.)
      1:    TN
             (Assign this if the access code is to be shared among specified TNs)
      2:    RSC
             (Assign this if the access code is to be shared among specified RSCs)
      3:    SFC
             (Assign this if the access code is to be shared among specified SFCs) When SRV=SSC (Service code) , SID56 (Floor Service) is assigned
When SRV=SSC (Service code), SID57 (Split Access) is assigned 
						

							CHAPTER 4 NDA-24288
Page 184
Revision 1.0
AGSPN
Table 4-1 SIDA (AGSPN)
SIDA SERVICE NAME SIDA SERVICE NAME
1-49–56 Guest/Admin. Service
50 UCD Busy Out; Entry 56-62–
51 UCD Busy Out; Cancel 63 Call Pickup Expand
52-55–64-255–
SERVICE INDEX A (SIDA) 1-255PNO 1-15A/G
56
PNO
This parameter specifies the Admin./Guest
Numbering Parameter Classification.
After assigning the PNO, go to the AOSP
command to skip this ACC.
After skipping the access code, the system
refers to the numbering data designated in
the next parameter A/G.A/G
Numbering table designation for redevelopment
A: Admin.
G: Guest
When SRV=SSCA (Service code appendix), SIDA56 (Guest/Admin. Service) is assigned
SERVICE INDEX  A (SIDA) 1-255
When SRV=SSCA (Service code appendix), SIDA50, 51 or 63 is assigned  
SIDA
Refer to Table SIDA (AGSPN). 
						

							NDA-24288 CHAPTER 4
Page 185
Revision 1.0
AGSPN
LOGICAL ROUTE NUMBER
(LGRT)
Assign a dummy route number.LGRT
Second dial tone sending (which is sent when a station has
dialed the digits specified in NND of the AGNP command)
0=Second DT is not sent
1=Second DT is sent2nd DTAuthorization code after dialing
ACC (LCR)+Destination number
0=Out of Service
1=In ServiceAH
ISDN-Sub Address Dialing
0=Out of Service
1=In ServiceSUB
LOGICAL ROUTE NUMBER
(LGRT)SECOND DIAL TONE
(2nd DT) 0/1AUTHORIZATION CODE
(AH) 0/1SUB ADDRESS DIALING
(SUB) 0/1 CNT (1-15) LOGICAL ROUTE NUMBER (LGRT)
When SRV=OGC (Outgoing call) is assigned
When SRV=OGCA (Outgoing call with route advance) is assigned
When SRV=LCR (Least cost routing) is assigned
When SRV=LCRS (Register sender LCR) is assigned
CNT
CNT is the route advance order.
1
2
3 
						

							CHAPTER 4 NDA-24288
Page 186
Revision 1.0
AGSPN
Assign the skip digits to terminate the call.
Assign the announce equipment number.
EQP3 and 5-14 can be used for SRV=ANNC (Single announcement).SKIP DIGITS
(SKIP) 0-5 When SRV=UNIF (Office termination) is assigned
When SRV=ANNC (Announcement service-Single announcement) is assigned
SKIP
ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 0-127
EQP
Note:This data is available for ACIS only. For CCIS, use the AUNE command.
Assign the tenant number of
the announcement trunk. When SRV=ANNCM (Announcement service-Multiple announcement) is assigned
TN TENANT NUMBER
(TN) 1-255 ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 122-125 Assign the announcement equipment number 
range from 122 to 125 (Multi announcement).EQP
When SRV=TELN (Telephone Number)
NECESSARY DIGIT
(NND) 1-16 
						

							NDA-24288 CHAPTER 4
Page 187
Revision 1.0
AGSPN
4. Data Sheet
(a) Service Code (SRV = SSC)
TENANT
 NUMBER
(TN)ACCESS
 CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS
INDEX
(CI) 
N/H/BKIND OF
SERVICE 
(SRV)SERVICE
INDEX
(SID)
1 – 63NUMBER OF
 NECESSARY
DIGITS
(NND)NUMBER OF 
NECESSARY
DIGIT FOR
SPEED
CALLING
(NND1)
1 – 24FUSION
POINT
CODE
FPC)
1-253SERVICE CONTENTS
H Hooking SSC 1Not used
NNormal
SSC 2
Dial Access to Attendant
(Operator Call) H Hooking
3Not used
4
NNormal
SSC 5
Call Waiting-Originating
BBusy
6Not used
N Normal SSC 7
Call Pickup-Group
8
13
Not used
N Normal SSC 14
Speed Calling-Station;
Entry
N Normal SSC 15
Speed Calling-System;
Access
N Normal SSC 16
TA S  A n s w e r
N Normal SSC 17
Individual Trunk Access
18Not used
B Busy SSC 19
OG Trunk Queueing: 
Entry
N Normal SSC 20
OG Trunk Queueing:
Cancel
N Normal SSC 21
Speed Calling-Station,
Group; Access
22
35
Not used
N Normal SSC 36
Hotel Service
Note:Use the sheets 
on the next 
page for the 
actual data 
entry.
~
~ 
						

							CHAPTER 4 NDA-24288
Page 188
Revision 1.0
AGSPN
(a) Service Code (SRV = SSC) (Continued)
SID = 36 (Hotel Service)
TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION
STATUS INDEX
(CI)
N/H/BKIND OF
SERVICE
(SRV)SERVICE
INDEX
(SID)MAID
STATUS
(STATE)
1 – 63SERVICE CONTENTS
N Normal SSC 361 To be cleaned without ID Code
2 Cleaned without ID Code
3Ready for Occupancy without ID 
Code
4 Use Not Allowed without ID Code
5
8Not used
9Maid Dial Answer Back without ID 
Code 1
10Maid Dial Answer Back without ID 
Code 2
11Maid Dial Answer Back without ID 
Code 3
12Maid Dial Answer Back without ID 
Code 4
13Maid Dial Answer Back without ID 
Code 5
14Maid Dial Answer Back without ID 
Code 6
15Maid Dial Answer Back without ID 
Code 7
16 Not used
17 To be cleaned with ID code
18 Cleaned with ID Code
19 Ready for Occupancy with ID Code
20 Use Not Allowed with ID Code
~