NEC Neax 2400 Imx Hotel Office Data Specification

							NDA-24288 CHAPTER 4
Page 129
Revision 1.0
AGSP
AGSP: Assignment of Guest Special Access Code
1. General
This command determines the Kind of Service to be executed or the route to be used when a Special Access
code or trunk Access code has been dialed for the Guest Station. 
2. Precautions
1. This command is used for the Hotel Application only.
2. If the Guest and Admin. Numbering are separated (the ASYD command, SYS1, INDEX 160, bit6=0), use
this command for the Guest Special Access code. For the Admin. Special Access code, use the AASP
command.
Note:Hotel features are available in TN1 only. If the numbering plans are separated by tenants, the purpose for
each tenant is completely separated. Admin. Station required of the guest room call must be allocated in
TN1.
3. If the numbering plan for Admin. and Guest is common (the ASYD command, SYS1, INDEX 160,
bit6=1), this command may be used to assign the Admin. Special Access code as well.
4. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS1, INDEX 8. Enter
the tenant number this command affects.
If data for this command is common for all tenants (ASYD command, SYS1, INDEX 92, bit1=1), assign
TN parameter as data “1” for all tenants.
5. To dial a different number of station number digits, the following programming is required.
Note:For the station number (ex. 200, 20000),
AANP
1st.: 2 CI: N & H NND: 3
AASP
ACC: 200* CI: N & H SRV: SSC SID: 36 STATE: 63 (Dummy STA)
6. The following information states the rules of NND/NND1 data for Speed Calling-System and Call Park
Remote Retrieval.
7. The variable parameter appears on the MAT depending on the data in the parameter SRV.
Service Feature SRV SID NND NND1
Speed Calling - System SSC 15NND is the number of digits of the ac-
cess code (ACC) NND1 is the number of digits abbre-
viated digits code (ADC)
Call Park Remote Retrieval 
CodeSSC 63NND is the number of digits of the ac-
cess code (ACC)- 
						

							CHAPTER 4 NDA-24288
Page 130
Revision 1.0
AGSP
3. Data Entry Instructions
 
Access code (Max. 6 digits)
15 (Speed Calling-System;
     Access)
63 (Call Park ; Retrieve) NND appears when the following SID is entered.
NND data is variable depending on SID.NND1 appears when SID = 15. The number of ADC
(Abbreviation Digit Code) digits should be assigned in NND1. TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAX. 6 DIGITSCONNECTION 
STATUS INDEX
(CI) N/H/BKIND OF
SERVICE (SRV)
ACC
CISRV
NND1
SERVICE INDEX
(SID) 1-63NECESSARY DIGIT
(NND)NECESSARY DIGIT FOR SPEED
CALLING (NND1) 1-24
NND
SID Number of digits for NND
N = Normal service
H = Hooking service
B = Busy service
Access Code (1-24)
Access Code (1-3) When SRV = SSC (Service code except SID36, 
56 and 57)  is assigned
SSC = Service code SSCA = Service code appendix
OGC = Outgoing call
OGCA = Outgoing call with route advance
LCR = Least cost routing LCRS = Register sending LCR
UNIF = Office termination
ANNC = Announcement service-single announcement
ANNCM = Announcement service-multiple announcement
PAGA = Paging answer PAGC = Paging cancel 
						

							NDA-24288 CHAPTER 4
Page 131
Revision 1.0
AGSP
         STATE
(Hotel Service Code)
  1 To be cleaned without ID code
  2  Cleaning Completed without ID code
  3 Ready for Occupancy without ID code
  4 Use Not Allowed without ID code
5-  8-
  9 Maid Dial Answer Back without ID code-1
10 Maid Dial Answer Back without ID code-2
11 Maid Dial Answer Back without ID code-3
12 Maid Dial Answer Back without ID code-4
13 Maid Dial Answer Back without ID code-5
14 Maid Dial Answer Back without ID code-6
15 Maid Dial Answer Back without ID code-7
16 -
17 To be cleaned with ID code
18 Cleaning Completed with ID code
19 Ready for Occupancy with ID code
20 Use Not Allowed with ID code
21 - 24 -
25 Maid Dial Answer Back with ID code-1
26 Maid Dial Answer Back with ID code-2
27 Maid Dial Answer Back with ID code-3
28 Maid Dial Answer Back with ID code-4
29 Maid Dial Answer Back with ID code-5
30 Maid Dial Answer Back with ID code-6
31 Maid Dial Answer Back with ID code-7 
32 Access code for Administration Station Call
33 Automatic Wake Up Setting, Cancel; Same Special code
34 For Guest Station Secretary Telephone; Boss/Secretary Calling
35 - 43 -
44 Direct Data Entry-Station (via Guest Station)
45 - 50 -
51 Same Special Code Time Zone Connection Change
52 Same Special Code Time Zone Connection Change
53 Same Special Code Time Zone Connection Change
54 Same Special Code Time Zone Connection Change
55 Same Special Code Time Zone Connection Change
56 - 62 -
63 Dummy Number
Note: STATE=1-15 are used at the time of Maid ID Code Service is not provided;
           (ASYD SYS1 INDEX 164, bit3=0)
           STSTE=17-31 are used at the time of Maid ID Code Service is provided;
           (ASYD SYS1 INDEX 164, bit3=1)
SERVICE INDEX
     (SID) 1-63       STATE
36 When SRV=SSC (Service code). SID36 (Hotel Service) is assigned 
						

							CHAPTER 4 NDA-24288
Page 132
Revision 1.0
AGSP
SERVICE INDEX
    (SID) 1-63      NO.1
56
NO.1
(Kind of Assignment Number)
  Available numbers are 0-15.
  This data is used to assign Floor Service data by the ASPF command.
Note: When programming Floor Service data,
 ASYD SYS1 INDEX 165, bit7=1 must have been assigned.
SERVICE INDEX
    (SID) 1-63NO.2KIND
57
NO.2
This parameter specifies the number (0-63) of the
access code being assigned for mutual Access.
This parameter serves as a counter for the access
codes being assigned.
Note: This parameter is used when assigning the
  details of the service by the ASPS command.
KIND: (0-3)
This parameter specifies the Split Access Parameter Classification. The data to
be assigned here depends on how the Guest and Administration stations are
differentiated.
The Guest and Administration stations may be assigned to separate TNs, RSCs,
and/or SFCs, or they may only be differentiated by their respective designations
as Administration or Guest.
      0:    Administration/Guest
             (Assign this if the access code is to be shared between Guest
             and Administration with no correspondence to TN, RSC or SFC.)
      1:    TN
             (Assign this if the access code is to be shared among specified TNs)
      2:    RSC
             (Assign this if the access code is to be shared among specified RSCs)
      3:    SFC
             (Assign this if the access code is to be shared among specified SFCs) When SRV = SSC (Service code), SID 56 (Floor Service) is assigned
When SRV = SSC (Service code), SID 57 (Split Access) is assigned 
						

							NDA-24288 CHAPTER 4
Page 133
Revision 1.0
AGSP
SERVICE INDEX A (SIDA) 1-255PNO 1-15A/G
56
PNO
This parameter specifies the Admin./Guest
Numbering Parameter Classification.
After assigning the PNO, go to the AOSP
command to skip this ACC.
After skipping the access code, the system
refers to the numbering data designated in
the next parameter A/G.A/G
Numbering table designation for redevelopment
A: Admin.
G: Guest
When SRV = SSCA (Service code appendix), SIDA 56 (Guest/Admin. Service) is assigned 
						

							CHAPTER 4 NDA-24288
Page 134
Revision 1.0
AGSP
Assign the number of advanced trunk routes.ROUTE NUMBER
(RT)
COUNT
Assign a dummy route number.RT
Second dial tone sending (which is sent when a station has
dialed the digits specified in NND of the AGNP command)
0 = Second DT is not send
1 = Second DT is sent2nd DTAuthorization code after dialing
ACC (LCR)+Destination number
0 = Out of Service
1 = In ServiceAH
ISDN-Sub Address Dialing
0 = Out of Service
1 = In ServiceSUB ROUTE NUMBER
(RT)SECOND DIAL TONE
(2nd DT) 0/1AUTHORIZATION CODE
(AH) 0/1SUB ADDRESS DIALING
(SUB) 0/1 INDEX COUNTER (COUNT)
INDEX ROUTE NUMBER (RT)
When SRV = OGC (Outgoing call) is assigned
When SRV = PAGA (Paging answer) is assigned
When SRV = PAGC (Paging cancel) is assigned
When SRV = OGCA (Outgoing call with route advance) is assigned
When SRV = LCR (Least cost routing) is assigned
When SRV = LCRS (Register sender LCR) is assigned
INDEX
INDEX is the route advance order.
1
2
3 
						

							NDA-24288 CHAPTER 4
Page 135
Revision 1.0
AGSP
Assign the skip digits to terminate the call.
Assign the announce equipment number.
EQP3 and 5-14 can be used for SRV = ANNC (Single announcement).SKIP DIGITS
(SKIP) 0-5 When SRV = UNIF (Office termination) is assigned
When SRV = ANNC (Announcement service-Single announcement) is assigned
SKIP
ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 0-127
EQP
Note:This data is available for ACIS only. For CCIS, use the AUNE command.
Assign the tenant number of
the announcement trunk. When SRV = ANNCM (Announcement service-Multiple announcement) is assigned
TN TENANT NUMBER
(TN) 1-255 ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 122-125 Assign the announcement equipment number 
range from 122 to 125 (Multi announcement).EQP 
						

							CHAPTER 4 NDA-24288
Page 136
Revision 1.0
AGSP
4. Data Sheet
(a) Service Code (SRV = SSC)
TENANT 
NUMBER
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS 
INDEX
(CI) 
N/H/BKIND OF
SERVICE 
(SRV)SERVICE
INDEX
(SID)
1 – 63NUMBER OF 
NECESSARY
DIGITS 
(NND)NUMBER OF 
NECESSARY
DIGIT FOR 
SPEED 
CALLING
(NND1)
1 – 24SERVICE CONTENTS
H Hooking SSC 1Not used
NNormal
SSC 2
Dial Access to Attendant 
(Information Service Call)
H Hooking
3Not used
4
NNormal
SSC 5
Call Waiting-Originating
BBusy
6
13
Not used
N Normal SSC 14
Speed Calling-Station; Entry
N Normal SSC 15Speed Calling-System; 
Access
N Normal SSC 16
TA S  A n s w e r
N Normal SSC 17
Individual Trunk Access
18
20
Not used
N Normal SSC 21
Speed Calling-Station, 
Group; Access
22
35
Not used
N Normal SSC 36
Hotel Service
~
~
~ 
						

							NDA-24288 CHAPTER 4
Page 137
Revision 1.0
AGSP
(a) Service Code (SRV = SSC) (Continued)
TENANT 
NUMBER 
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS INDEX 
(CI) 
N/H/BKIND OF 
SERVICE 
(SRV)SERVICE 
INDEX
(SID)MAID
STATUS 
(STATE)
1 – 63SERVICE CONTENTS
N Normal SSC 361 To be cleaned without ID Code
2 Cleaned without ID Code
3Ready for Occupancy without ID 
Code
4 Use Not Allowed without ID Code
5
8Not used
9Maid Dial Answer Back without ID 
Code 1
10Maid Dial Answer Back without ID 
Code 2
11Maid Dial Answer Back without ID 
Code 3
12Maid Dial Answer Back without ID 
Code 4
13Maid Dial Answer Back without ID 
Code 5
14Maid Dial Answer Back without ID 
Code 6
15Maid Dial Answer Back without ID 
Code 7
16 Not used
17 To be cleaned with ID code
18 Cleaned with ID Code
19 Ready for Occupancy with ID Code
20 Use Not Allowed with ID Code
~ 
						

							CHAPTER 4 NDA-24288
Page 138
Revision 1.0
AGSP
(a) Service Code (SRV = SSC) (Continued)
TENANT 
NUMBER 
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS INDEX
(CI) 
N/H/BKIND OF 
SERVICE
(SRV)SERVICE 
INDEX
(SID)MAID
STATUS 
(STATE)
1 – 63SERVICE CONTENTS
N Normal SSC 3621
24Not used
25Maid Dial Answer Back with ID 
Code 1
26Maid Dial Answer Back with ID 
Code 2
27Maid Dial Answer Back with ID 
Code 3
28Maid Dial Answer Back with ID 
Code 4
29Maid Dial Answer Back with ID 
Code 5
30Maid Dial Answer Back with ID 
Code 6
31Maid Dial Answer Back with ID 
Code 7
32 Not used
33Automatic Wake-Up Setting, 
Cancel; Same Special Code
34For Guest Station Secretary 
Telephone; Boss/Secretary
35
43Not used
44 Direct Data Entry – STA
45
50Not used
51Same Special Code Time Zone 
Connection Change
~
~
~