NEC Neax 2000 Ivs2 Wcs System Manual

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk Data Programming (For Adjunct Analog)
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 63
DESCRIPTION DATA
Specify the DTMF Sender release timing
to the trunk route.
(1)
(2)YY=46
00-63 : Trunk Route No.
0:2sec.
1:4sec.
2:6sec.
3:8sec.
4:12sec.
5:14sec.
6:16sec.
7:10sec.
Specify the designated seizure of trunks
on each station basis.
(1)
(2)YY=98
00-63 : Trunk Route No.
0 : Allowed
Specify the COT card Terminating Imped-
ance.
(1)
(2)YYY=100
00-63 : Trunk Route No.
0 : 600 ohm/complex BNW for Inte-
grated Type and Adjunct Type
(CCIS Interface)
2 : 600 ohm/600 ohm for Adjunct
Type (Analog Interface)
Assign the trunk to be seized on each PS
station basis.
(1)
(2)YY=16
X-XXXXXXXX : PS Station No.
D000-D255 : Trunk No.
CM35
D
CM12
END 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 64ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
WCS FEATURE PROGRAMMING
Announcement-PS No Answer/Announcement-PS Out of Cell
See the WCS Features and Specifications.
DESCRIPTION DATA
Assign a Digital Announcement Trunk
(DAT) circuit number to the required LEN.
NOTE 1:The DAT circuit No. must be as-
signed to the first LEN (Level 0),
the third LEN (Level 2), the fifth
LEN (Level 4), and the seventh
LEN (Level 6) of each LT slot.
NOTE 2:EB000 and EB001 are dedicated
to built-in Digital Announcement
Trunk of MP card.(1)
(2)000-763: LEN
0-7 (PIM0-7) +
00-63 (Port No.)
EB002-EB127: Digital Announcement
Trunk circuit No.
For PIM 0/1 : EB002-EB031
For PIM 2/3 : EB032-EB063
For PIM 4/5 : EB064-EB095
For PIM 6/7 : EB096-EB127
Assign a tenant No. to a PS station. 
(1)
(2)YY=04
X-XXXXXXXX: PS Station No.
00 : Tenant 00
1 : Tenant 01
63 : Tenant 63
Provide PS No-Answer feature. (1)
(2)504
0 : Available
1 : Not Available
Specify types of No-Answer Timer. (1)
(2)085
0: No-Answer timer (CM41 Y=0>86)
1: No-Answer timer (CM41 Y=0>01)
Specify the message reply timer for
Announcement -PS No Answer.
(1)
(2)Y=0
01
01-30: 4-120 sec. in 4 sec. increments
If no data is set, the default setting is
32-36 seconds.
Specify the duration of message for
Announcement -PS No Answer.
(1)
(2)Y=0
75
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is
116-120 seconds.
CM12 START
CM10
CM41
CM08
~
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 65
DESCRIPTION DATA
Specify the duration of message for
Announcement-PS Out of Cell/PS Power
Off.
(1)
(2)Y=0
84
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is
116-120 seconds.
Specify the message reply timer for
Announcement-PS No Answer.
NOTE:CM41 Y=0>01 is effective only
when CM08>085 is set to 0.
(1)
(2)Y=0
86
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is
36-40 seconds.
Specify the message reply timer for
Announcement-PS Out of Cell/PS Power
Off.
(1)
(2)Y=0
85
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is 8-
12 seconds.
Provide the Announcement Service. 
(1)
(2)Y=5
00: PS No-Answer
02: PS Out of Cell/PS Power Off
0500 : Provided
NONE : Not provided
Assign the function for each Digital
Announcement Trunk.
(1)
(2)YY=00
002-127 : Digital Announcement
Trunk Circuit No. (EB002-
EB127)
1300-1363 : PS No Answer Message
Group No. 00-63
1500-1563 : PS Out of Cell/PS Power
Off Message Group No.
00-63
NONE : None
Assign the message group for PS No
Answer to each tenant.
(1)
(2)YY=10
00-63 : Tenant No.
00-63 : Message Group No.
NONE : None
Assign the message group for PS Out of
Cell/PS Power Off to each tenant.
(1)
(2)YY=12
00-63 : Tenant No.
00-63 : Message Group No.
NONE : None
CM41
A
CM48
CM49
B 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 66ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
To record/replay/delete a message:
There are two methods to record/replay/delete a message from a PS or a station.
(1) To record/replay/delete a message from a station or a PS by dialling an access code
assigned by CM20, do the following programming.
This method is available only for the IntegratedType.
(2) To record/replay/delete a message from a PS by dialling “1”, “2”, “3”, do the following
programming.
This method is available for both the Integrated Type and the AdjunctType.
DESCRIPTION DATA
Assign the Class of Service for the
Announcement Service to a certain PS/
station.

(1)
(2)CM12 YY=02
(Service Restriction Class A)
CM15 YY=33
(Digital Announcement Trunk Access:
Record/Replay/Delete)
00-15 : Service Restriction Class A
0 : Restricted
1 : Allowed
Assign the access codes to record/replay/
delete the message.
(1)
(2)Y=0-3 (Numbering Plan Group 0-3)
X-XXXX: Access Code
A100 : Record
A101 : Replay
A102 : Delete
CM12
B
END
CM15
CM20 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 67
For operating procedure, see the following pages.
DESCRIPTION DATA
Assign the Class of Service for the
Announcement Service to a certain PS
station.
NOTE:By this method, while a PS is
specified to “Allowed” to record/
replay/delete a message by
CM15 YYY=110, the PS cannot
originate a call. Specify to
“Restricted” by CM15 YYY=110
again after a message is
completed to record/replay/
delete.

(1)
(2)CM12 YY=02
(Service Restriction Class A)
CM15 YYY=110
(Digital Announcement Trunk Access:
Record/Replay/Delete)
00-15 : Service Restriction Class A
0 : Restricted
1:Allowed
CM12
B
END
CM15 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 68ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
Operating Procedure for Announcement Service
(1) By dialling predetermined access cord from a station or a PS (For Integrated Type)
To replay an announcement:
1. Dial the access code to replay the announcement assigned by CM20.
2. Dial the Digital Announcement Trunk Circuit Number (000-127).
3. Press the SEND key.
4. Receive a message.
5. Press the END key.
To record an announcement:
1. Dial the access code to record the announcement assigned by CM20.
2. Dial the Digital Announcement Trunk Circuit Number (000-127).
3. Press the SEND key.
4. Receive a service set tone.
5. Record a message.
6. Press the END key.
To delete an announcement:
1. Dial the access code to delete the announcement assigned by CM20.
2. Dial the Digital Announcement Trunk Circuit Number (000-127).
3. Press the SEND key.
4. Receive a service set tone.
5. Press the END key. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 69
(2) By dialling “1”, “2”, “3”, from a PS (For Integrated Type and AdjunctType)
To replay an announcement:
1. Dial “2”.
2. Dial the Digital Announcement Trunk Circuit Number (000-127).
3. Press the SEND key.
4. Receive a message.
5. Press the END key.
To record an announcement:
1. Dial “1”.
2. Dial the Digital Announcement Trunk Circuit Number (000-127).
3. Press the SEND key.
4. Receive a service set tone.
5. Record a message.
6. Press the END key.
To delete an announcement:
1. Dial “3”.
2. Dial the Digital Announcement Trunk Circuit Number (000-127).
3. Press the SEND key.
4. Receive a service set tone.
5. Press the END key. 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 70ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
Call Forwarding-Not Available
Refer to the WCS Features and Specifications.
DESCRIPTION DATA
Assign the destination VMS station for Call
Forwarding-Not Available.
(1)
(2)YY=20
00-63: Tenant No. of Virtual PS
X-XXXXXXXX: VMS Station No.
Assign the access code to set/cancel Call
Forwarding when the incoming call is not
available, and set the access code to
replay the message.
(1)
(2)Y=0-3 (Numbering Plan Group 0-3)
X-XXXX: Access Code
A089: Call Forwarding-Not Available
Set
A090: Call Forwarding-Not Available
Cancel
A091: Call Forwarding-Not Available
Replay
Specify whether confirmation of message
existence by Special Dial Tone is available
or not.
If the second data is set to 0, the Special
Dial Tone is sent when a message exists.
(1)
(2)Y=2
12 (Confirmation by DialTone)
0 : Available
1 : Not available
Set the Class of Service for Call Forward-
ing-NotAvailabletoeachPSstation.

(1)
(2)CM12 YY=02
(Service Restriction Class A)
CM15 YYY=115
(Call Forwarding-Not Available)
00-15 : Service Restriction Class A
for the Vir tual PS Station
0 : Restricted
1:Allowed
CM48 START
CM51
CM15
END
CM12
CM20
INITIAL 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 71
Calling Name Display-PS
Refer to the WCS Features and Specifications.
Refer to the following manuals for the name display feature programming.
Feature Programming Manual : Alphanumeric Display, Caller ID Class, Guest Name Display
CCIS System Manual : Calling Name Display-CCIS
DESCRIPTION DATA
Specify the terminal kind of the PS as
“D
termPS II”.
(1)
(2)YY=15
X-XXXXXXXX: PS station No.
(Assigned by CM1C)
00 : D
termPS II
Specify the kind of the ZT as “D
termPS II
type ZT”.
(1)
(2)YY=19
000-127 : ZT No.
00 : D
termPS II type ZT
Assign a Service Restriction Class to each
station.
(1)
(2)YY=02
X-XXXXXXXX: PS station No.
(Assigned by CM1C)
XX ZZ
XX: Service Restriction Class A
(00-15 )
Provide Calling Name Display to PS
NOTE:The previous PS D
termdoes not
provide the Calling Name
Display feature; therefore, CM15
YYY=123 should be set to “1”
Not Available. Set data to “0”
Available if providing service for
the D
termPS II.
(1)
(2)YYY=123
00-15 : Service Restriction Class A
assigned by CM12 YY=02
0:Available
1:NotAvailable
START
CM1D
CM15
CM12
CMAD
END 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 72ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
WCS Feature Programming
Group Call-Automatic Conference (6/10-Party)
Refer to the WCS Features and Specifications.
DESCRIPTION DATA
Assign a Conference Trunk card number to
the required LEN.(1)
(2)000-763 : LEN
0-7 (PIM0-7) +
00-63 (Port No.)
ED00-ED03: Conference Trunk Card
No.
Assign the stations which belongs to each
paging group, and their number within the
group. A maximum of 9 stations can be
paged simultaneously except the
conference leader.
NOTE 1:Single line telephones, D
terms
and PSs can be assigned as the
station within the group.
A vir tual-line cannot be
assigned.
NOTE 2:A station can belong to plural
group.
(1)
(2)YY=00-07: Simultaneous Paging
Group 0-7
00-15 : Serial No. within the Group
X-XXXXXXXX: Station No.
Assign a Service Restriction Class to each
station.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX YY
XX : Service Restriction Class A
(00-15 )
Allow the Service Restriction Class A to
page the conference.
(1)
(2)YYY=119
00-15: Service Restriction Class A
assigned by CM12 YY=02
0: Allowed
START
CM56
A
CM12
CM15
CM10
INITIAL