NEC Neax 2000 Ivs2 Wcs System Manual

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 93
Visitor PS Data Programming
DESCRIPTION DATA
Execute System Data Memory All Clear of
the DBM (PN-AP00-A) card.
The System Data Memory All Clear must
be done at theinitial setup.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=999
1(AllClear)
CCC
Execute Work Memory All Clear of the
DBM card.
The Work Memory All Clear must be done
before the system star ts operating. All
HLR and VLR data are cleared by this
command.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=998
1(AllClear)
CCC
Assign the Home PBX ID of Visitor PS and
its data table number.
This data is used to define the PBX for
which the PS can perform Roaming.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=000
X-XXXX: Home PBX ID
(1-4 digits, Decimal)
000-511: Data Table No.
CCC : Data Clear
NONE
Assign the Home PBX ID of Visitor PS and
its data table number.
This data is used to define the route used
for registration of the PS location.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=001
000-511: Data Table No. assigned by
CMAF Y=000
00-07 : Route Selection Pattern No.
CCC : Data Clear
NONESTART
CMAF
A 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 94ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign the Trunk Route to be used for
requesting the data of the Visitor PS
against its Home PBX.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=100-107
(Route Selection Pattern No. 00-07)
1-4: First-Fourth Selected Route
00-63 : Q931a D ChannelTrunk
Route No.
NONE : No Data
CCC : No Data Clear
Assign the default restriction class for
Visitor PS.
This data is valid when the DBM card is
on-line.
NOTE:The Roaming will not work
properly if the second data is set
to Default (NONE). It must be set
to any value from 01 to 08.
(1)
(2)YYY=002
000-511: Data table No. Assigned by
CMAF Y=000
01-08 : Default restriction class of
Visitor PS.
NONE : No Data (Default)
Assign the Vir tual Line number for the
Visitor PS to the required LEN.
NOTE 1:The Vir tual Line No. must be
assigned from the last LEN 763.
NOTE 2:The Virtual station No. for Visitor
PS must be maximum 4 digits.(1)
(2)000-763: LEN
0-7 (PIM0-7) + 00-63 (Por t No.)
X-XXXX: Virtual station No.
NONE : No Data
Assign an access code for LCR Group 0-3
if necessary.
(1)
(2)Y=0-3 (Numbering Plan 0-3)
X-XXXX: Access Code
A126: LCR Group 0
A127: LCR Group 1
A128: LCR Group 2
A129: LCR Group 3A
CMAF
CM10
B
CM20 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 95
DESCRIPTION DATA
Specify a path between the virtual line and
virtual trunk.
(1)
(2)YY=00
256-511: Virtual Trunk No.
NOTE 1,NOTE 2
X-XXXX: Virtual Station No.
The following data are set automatically by the virtual line-trunk path setting of CM5A
YY=00. If you clear CM5A YY=00 setting data, the following data are also cleared
automatically.
CM5A
B
C
COMMAND
CODE MEANINGS 1ST DATA 2ND DATA MEANING
CM12 YY=00 DTMF/DP Virtual Station No.
assigned by CM10
1DP
CM13 YY=18 Reverse signal
sending to stationVirtual Station No.
assigned by CM10
0Send
CM30 YY=00 Trunk route
allocationVir tual Trunk No.
256-511
63
NOTE 3
Trunk Route No. 63
CM30 YY=02 Terminating system
in Day ModeVir tual Trunk No.
256-511
04
NOTE 4
Direct-In Termination
CM30 YY=03 Terminating system
in Night ModeVir tual Trunk No.
256-51104
NOTE 4
Direct-In Termination
CM30 YY=40 Terminating system
in Mode AVir tual Trunk No.
256-51104
NOTE 4
Direct-In Termination
CM30 YY=41 Terminating system
in Mode BVir tual Trunk No.
256-51104
NOTE 4
Direct-In Termination 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 96ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
NOTE 1:PS station No. is assigned by the first data of CM1C (Virtual PS LEN) as follows.
Virtual PS LEN=Virtual Trunk No. minus 256
For example, when the Vir tual Trunk No. is 256 (CM5A YY=00 1st data: 256), then
the Vir tual PS LEN is 000 (CM1C 1st data: 000).
NOTE 2:When the Expansion Memory card (PZ-M537) is not mounted on the MP card, the
first data is 256-383.
NOTE 3:The trunk route data must be assigned by CM35, because the trunk route data are
not automatically assigned.
The trunk route of the Virtual Trunk is 63 by the default data setting. Be sure to as-
sign the separate trunk route number of Virtual Trunk for Home PS and Visitor PS
by CM30 YY=00.
NOTE 4:The second data of CM30 YY=02, 03, 40, 41 are set to “4” (Direct -In Termination)
automatically by CM5A YY=00.
Be sure to change these data to “22” (Roaming Termination), for Roaming service.
CM5A
C
D 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 97
DESCRIPTION DATA
Assign the Service Restriction Class of the
Virtual LC for the Visitor PS.
Assign the different class to the Virtual LC
for Visitor PSs from the station and Home
PS of the PBX.
(1)
(2)YY=02
X-XXXX: Virtual LC station No.
XX YY
XX: Service Restriction Class A
(00-15 )
YY: Service Restriction Class B
(00-15 )
Assign the Service Restriction Class C of
the Vir tual LC for the Visitor PS.
(1)
(2)YY=07
X-XXXX: Virtual LC station No.
00-15 : Service Restriction Class C
Allow the Vir tual LC for the Visitor PS to
use Roaming.
(1)
(2)YY=39
X-XXXX: Virtual LC station No.
0: Available
For the Virtual LC for the Visitor PS,
restrict the station service data of CM15
YY=00-115.
(1)
(2)YY=00, 02, 03, 10, 11, 12, 13, 15, 16,
19, 22, 26, 27, 28, 29, 40, 41, 44, 47,
48, 49, 115.
00-15 (Service Restriction Class A)
0: Restricted
Assign a Trunk Route to each trunk num-
ber used for Virtual COT for the Visitor PS.
Make a separate route from the Home PS.
(1)
(2)YY=00
000-255: Trunk No.
00-63: Trunk Route No.
Assign the terminating system to the
Virtual COT as “Roaming Termination”.



(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
YY=40 (Mode A)
YY=41 (Mode B)
000-255: Trunk No.
22: Roaming Termination
CM12
D
E
CM13
CM15
CM30 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 98ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Assign trunk route data to the Virtual COT
route number for the visitor PS assigned
by CM30 YY=00.
(1)
(2)YY=00 (Kind ofTrunk Route)
00-63 : Route No.
00: ISDN/C.O. Trunk

(1)
(2)YY=01 (Dialing Signal Type)
00-63 : Route No.
4 : Call Termination; DTMF
Call Origination; DTMF
7 : Call Termination; DP/DTMF
Call Origination; DTMF

(1)
(2)YY=04
(Answer Signal from Distant Office)
00-63 : Route No.
1 : Answer Signal arrives (C.O.)

(1)
(2)YY=05
(Release Signal from Distant Office)
00-63 : Route No.
1 : Release signal arrives

(1)
(2)YY=14(SMDRforOutgoingCall)
00-63 : Route No.
0 : Not to be provided
1 : To be provided

(1)
(2)YYY=139 (Roaming)
00-63 : Route No.
0 : Available
CM35
E
F 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 99
DESCRIPTION DATA
Specify the Route Selection Pattern Num-
ber as “Pattern Number 0”, for all classes
of the Trunk Restriction Class (01-06) sent
from the Home PBX.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=208
01-06 : Trunk Restriction Class sent
from the Home PBX
00 : Route Selection Pattern 0
Specify the Virtual COT trunk route to be
used for originating/terminating calls from/
to the Visitor PS.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=200
(Route Selection Pattern 0)
1: First Selected Route
00-63 : Trunk Route
NONE : No Data
Assign the Station Hunting Group of the
virtual LCs for the Visitor PSs.
All the Virtual LC stations in one Hunting
Group must be the Virtual LC Station
corresponds to the Virtual COTs for which
the same trunk route is assigned.
(1)
(2)Y=0
X-XXXX: Virtual LC station No.
X-XXXX: Virtual LC station No.
Specify the kind of station for a Virtual LC
Station as a Pilot station, and for other
Virtual LC stations as a Member station.
(1)
(2)Y=1
X-XXXX: Vir tual LC station No.
0 : Member station
1 : Pilot station
Assign the Roaming station number for the
Visitor PS. For the Roaming station
number, set the Vi rtual LC Pilot station
number specified by CM18 Y=1.
This data is valid when the DBM card is
on-line.
(1)
(2)YYY=210
00 (Roaming Number Assignment)
X-XXXX: Roaming station number
CMAF
F
CM18
G
CMAF 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 100ND-70920 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Multi-Site Roaming Programming
DESCRIPTION DATA
Provide the Visitor PS with the capability to
enter an Account Code, if required.
(1)
(2)YY=30
00-15 (Service Restriction Class A
assigned by CM12 YY=02)
0 : Restricted
1:Allowed
Specify the maximum number of Account
Code.(1)
(2)10 (Max. digits for Account Code)
01-16 : 01-16 digitsG
CM15
END
CM42 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Maintenance Data Programming
NEAX2000 IVS2WCSSystemManual(PCS)
ND-70920 (E), Issue 1.0Page 101
MAINTENANCE DATA PROGRAMMING
DESCRIPTION DATA
Assign the registration of fault information
into Memory and the control of the
external alarm.
(1)
(2)Y=2
12 : ZT fault occurred
2B : ZT fault occurred
3B : ZT fault recovered
0 : Registration of fault memory
No output of External alarm
1 : Registration of fault memory
External alarm is MN alarm
2 : Registration of fault memory
External alarm is MJ alarm
3 : Registration of fault memory
External Alarm kind is deter-
mined in standard data
NONE : No Registration of Fault
Memory/No output of
External alarmSTART
END
CMEA 
						

							NEAX2000 IVS2WCS System Manual (PCS)Page 102ND-70920 (E), Issue 1.0
This page is for your notes.